Q: How to start and operate the RYOBI One+ RLT1831H20F brush cutter?

Before the first start: Install a RYOBI One+ 18 V battery by fully inserting it (it must be charged) Check that the cutting accessory is properly in place and securely tightened Ensure that all guards, deflectors, and handles are properly in place and locked Install new nylon line of the appropriate diameter in the spool (remove the spool cover to access part 9) To start: Adjust the length of the shaft using the telescopic collar according to your body type Position the device: use the pivot button to choose between the horizontal position (bush cutting) or vertical position (edging) Simply press the trigger to start - the cutting speed is variable depending on your pressure on the trigger Mandatory safety equipment: Wear protective goggles, hearing protection, gloves, long pants, and non-slip shoes.

Q: How do I adjust the cutting width of the RYOBI One+ RLT183250F?

The cutting width of the RYOBI One+ RLT183250F is fixed at a maximum of 25 cm and is not adjustable. This dimension is determined by the design of the protective cover and the cutting head of the device. The only available adjustment concerns the length of the cutting line , which adjusts automatically by tapping the cutting head on the ground during operation. This gradually releases more line as needed. If you want a different cutting width, you will need to consider another model from the RYOBI range.

Q: Does the RYOBI RLT6130 trimmer use a single line or two cutting lines?

The RYOBI RLT6130 uses a single cutting line with a rotating head system. The line is automatically fed by a spool system integrated into the cutting head. Here are the essential characteristics of the line: Material : nylon line only (metal alternatives are strictly prohibited) Diameter : according to the specifications in the manual (refer to the specifications section of your manual) Supply : use only RYOBI branded nylon line Your device is equipped with a small blade incorporated into the protective casing that allows for automatic cutting of the line to the appropriate length after release. Ensure that the cutting head is securely fastened and in good condition before each use.

Question 1

How to change the cutting line of the RYOBI One+ RY18LTX38A grass trimmer?

Accepted Answer

To change the cutting line of your RYOBI One+ RY18LTX38A grass trimmer, follow these simple steps:

Before you begin

Turn off the device and remove the battery. This tool is equipped with a Tap & Go head that allows the line to automatically unwind by tapping the head on the ground.

Replacement procedure

Unscrew the cap of the cutting head
Remove the used spool
Install the new spool, ensuring the correct rotation direction
Thread the ends of the line through the eyelets
Reattach the cap

Line specifications

Type: nylon line only

Diameter: 2 mm (as per the manual)

Source: only use line provided by the manufacturer RYOBI

Important: never use metal blades with this tool.

Question 2

How to remove a stuck cord under the spool of the RYOBI One+ RLT1831H20F?

Accepted Answer

If a cord is stuck under the spool (spool cover) of your RYOBI One+ RLT1831H20F, here are the steps to follow:

Safety first

Turn off the device and disconnect the battery before any intervention

Release procedure

Locate the spool cover (part no. 8)
Remove the cover to access the spool (part no. 9)
Manually free the stuck wire once access is obtained
Replace the cover

Important point

After the release, check that the wire feed system is working properly. The jamming may be due to the ground contact finishing system.

If the wire remains stuck despite your efforts or if the spool is damaged, contact an authorized RYOBI service center rather than forcing it.

Question 3

How to start and operate the RYOBI One+ RLT1831H20F brush cutter?

Accepted Answer

Before the first start:

Install a RYOBI One+ 18 V battery by fully inserting it (it must be charged)
Check that the cutting accessory is properly in place and securely tightened
Ensure that all guards, deflectors, and handles are properly in place and locked
Install new nylon line of the appropriate diameter in the spool (remove the spool cover to access part 9)

To start:

Adjust the length of the shaft using the telescopic collar according to your body type
Position the device: use the pivot button to choose between the horizontal position (bush cutting) or vertical position (edging)
Simply press the trigger to start - the cutting speed is variable depending on your pressure on the trigger

Mandatory safety equipment: Wear protective goggles, hearing protection, gloves, long pants, and non-slip shoes.

Question 4

Why does my RLT183220S trimmer have difficulty turning?

Accepted Answer

Cleaning the hub and cutting head

If your RYOBI One+ RLT183220S trimmer is difficult to turn, grass or debris accumulated around the hub and cutting head is usually the cause. Here’s how to resolve the issue:

Stop the device immediately and remove the 18V lithium-ion battery to ensure your safety.
Mechanical cleaning - Use a clean, dry cloth to completely remove grass, debris, and residues accumulated around the hub and the cutting head area. This is the essential step according to the maintenance manual.
Check the tightness - Check the tightness of the nuts, screws, and bolts around the cutting head, as lack of tightness can also cause friction or difficult rotation.

If the problem persists

After a complete cleaning, if the device still turns difficultly, it is a sign that the problem comes from the inside (damaged bearing, worn motor, internal mechanical resistance). In this case, contact an authorized RYOBI service center - only a qualified technician can safely intervene on the internal components of your device.

Question 5

How do I adjust the cutting width of the RYOBI One+ RLT183250F?

Accepted Answer

The cutting width of the RYOBI One+ RLT183250F is fixed at a maximum of 25 cm and is not adjustable. This dimension is determined by the design of the protective cover and the cutting head of the device.

The only available adjustment concerns the length of the cutting line, which adjusts automatically by tapping the cutting head on the ground during operation. This gradually releases more line as needed.

If you want a different cutting width, you will need to consider another model from the RYOBI range.

Question 6

How to reload the cutting line of the RYOBI RLT5127?

Accepted Answer

To reload the cutting line of your RYOBI RLT5127 trimmer, you need to use 1.65 mm diameter nylon line. Never use metal line, as it would damage the device and safety guards.

Reloading procedure:

Unplug the device and let it cool down
Unscrew the existing cutting head in a counterclockwise direction until it is completely removed
Insert a new head or a replacement spool pre-loaded with 1.65 mm nylon line
Screw the head back on tightly in a clockwise direction until it is securely fastened
Before starting, always ensure that the product is in normal working position

Important points: The small blade integrated into the protective casing automatically trims the newly released cutting line to the correct length to ensure optimal performance and safety. Never touch this blade during cleaning. If you only need to unwind a new length of existing line, simply press the rotary release button to release the line, then gently tap the head against the ground to unwind it.

Maintenance after use: Clean the cutting head and the device with a clean, dry cloth after each use to prevent debris buildup and line tangling issues. Only use cutting line provided by the manufacturer or equivalent quality 1.65 mm nylon line.

Question 7

Does the RYOBI RLT6130 trimmer use a single line or two cutting lines?

Accepted Answer

The RYOBI RLT6130 uses a single cutting line with a rotating head system. The line is automatically fed by a spool system integrated into the cutting head.

Here are the essential characteristics of the line:

Material: nylon line only (metal alternatives are strictly prohibited)
Diameter: according to the specifications in the manual (refer to the specifications section of your manual)
Supply: use only RYOBI branded nylon line

Your device is equipped with a small blade incorporated into the protective casing that allows for automatic cutting of the line to the appropriate length after release. Ensure that the cutting head is securely fastened and in good condition before each use.

Question 8

How to assemble the RYOBI RY18BCX26A grass trimmer?

Accepted Answer

The assembly of the RYOBI RY18BCX26A cordless trimmer is done in a few simple and quick steps.

Before you begin, remove the 18 V lithium-ion battery for safety reasons. Prepare the supplied accessories: the wrench, the washers (spring, construction, and flange), the nut, and the blade guard.

Installing the harness: First, adjust the quick-release harness so that it comfortably supports the weight of the product on your right side. Familiarize yourself with the quick-release mechanism before use - this is essential for emergency situations.

Mounting the cutting head or blade: Place the product on the ground with the blade facing up (this extends the life of the blade). Select the desired accessory: the nylon line head for the trimmer, the TRI-ARC blade for the brush cutter (max diameter 13 mm), or the saw blade (max diameter 40 mm). Secure the accessory using the flange washer, construction washer, spring washer, and the provided nut. Tighten firmly with the wrench while wearing protective gloves (the blades have very sharp edges). Ensure that the accessory is properly in place and locked before any use.

Installing the cutting line: If you are using the cutting head, locate the protective cover with the cutting blade. Open the cover of the cutting head and insert nylon line of the specified diameter (refer to the specifications table in the manual). Wind the line according to the direction indicated on the internal spool. Close the cover of the cutting head securely.

Final safety checks: Ensure that all protective elements, deflectors, and handles are properly and securely attached. Make sure that the cutting line blade in the protective cover is correctly positioned. Always remove the blade guard before use. Install the 18 V lithium-ion battery and test the device while empty before full use. The product should only be used at temperatures between 0°C and 40°C.

Question 9

How to change the cutting line of the RYOBI OLT1833 trimmer?

Accepted Answer

To change the cutting line of your RYOBI OLT1833, follow these steps:

Turn off the device and remove the 18V battery from the One+ system
Open the spool cover at the top of the cutting head
Remove the empty spool
Wrap about 4 meters of new nylon line onto the spool, following the direction indicated on the spool
Reinstall the spool and close the cover
Pull both ends of the line to release them and trim to the required cutting length

Make sure to use only nylon line of the appropriate diameter compatible with the trimmer. For more details on the exact diameter and specifications, refer to your user manual. Always wear gloves and safety glasses during this operation.

Question 10

Why does the line of the RYOBI RY36LT33A trimmer loosen but not cut?

Accepted Answer

If the line continuously loosens without being cut by the blade, it generally indicates a poor contact with the line cutting blade or an issue with the diameter/quality of the line used. Here’s how to diagnose and resolve:

Check the diameter and quality of the line

The manual specifies the exclusive use of nylon line with a 1.6 mm diameter. A line with a smaller diameter or of poor quality may not provide enough stiffness to be properly cut by the blade. Ensure you are using line of the exact recommended diameter.

Inspect the line cutting blade

The blade mounted on the guard (deflector) is responsible for cutting the extending line. Examine this blade:

Check that it is not worn, dull, or damaged.
Ensure there is no nylon residue or debris blocking its operation.
Gently clean around the blade (caution: it is very sharp).

Check the positioning of the line

After unwinding a new length of line, always replace the device in normal working position before turning it on. Poor positioning may prevent the line from passing correctly under the blade.

Test the operation

Start the device for a few seconds in normal mode. The extending line should be automatically cut to the correct length by the blade. If the problem persists after these checks, the blade may need replacing or the device may require further diagnosis.

User manual RYOBI String trimmer : user manuals and guides in PDF

Models RYOBI String trimmer most viewed

Other categories RYOBI

Recent questions about String trimmer RYOBI