Q: Does the RYOBI RLT6130 trimmer use a single line or two cutting lines?

The RYOBI RLT6130 uses a single cutting line with a rotating head system. The line is automatically fed by a spool system integrated into the cutting head. Here are the essential characteristics of the line: Material : nylon line only (metal alternatives are strictly prohibited) Diameter : according to the specifications in the manual (refer to the specifications section of your manual) Supply : use only RYOBI branded nylon line Your device is equipped with a small blade incorporated into the protective casing that allows for automatic cutting of the line to the appropriate length after release. Ensure that the cutting head is securely fastened and in good condition before each use.

Q: How does the line feed work on the RYOBI ONE+ RLT183225FPK?

The RYOBI ONE+ RLT183225FPK uses a cutting head with a removable line spool . Although the product manual does not explicitly detail the feed mechanism, here is how the cutting system works: Cutting system: Rotating nylon line (no metal blade) A small blade mounted on the guard that automatically cuts the line to the correct length during rotation Removable spool with cover for easy replacement or adjustment For more precise technical details on the line diameter and the exact operation of the feed system, we recommend consulting the complete documentation from the manufacturer RYOBI or contacting an authorized dealer (for example, Leroy Merlin) who can confirm whether this model has a fully automatic or semi-automatic feed.

Q: How to replace the cutting line of the RYOBI One+ RY18LT33A trimmer?

Before you begin Make sure the product is turned off and the battery is removed before any maintenance operation. Caution: the small blade attached to the housing is very sharp - do not touch it. Replacement steps Press the release buttons located on the side of the tool Remove the old line spool Insert the new spool following the indicated rotation instructions Reassemble the tool Type of line to use Only use a 1.6 mm diameter nylon cutting line , compatible with RYOBI trimmers. Ensure that the diameter matches exactly what is indicated in the specifications table. Maintenance after replacement After each use, clean the product with a clean, dry cloth, and regularly check the condition of the line spool.

Question 1

How to reload the cutting line of the RYOBI RLT5127?

Accepted Answer

To reload the cutting line of your RYOBI RLT5127 trimmer, you need to use 1.65 mm diameter nylon line. Never use metal line, as it would damage the device and safety guards.

Reloading procedure:

Unplug the device and let it cool down
Unscrew the existing cutting head in a counterclockwise direction until it is completely removed
Insert a new head or a replacement spool pre-loaded with 1.65 mm nylon line
Screw the head back on tightly in a clockwise direction until it is securely fastened
Before starting, always ensure that the product is in normal working position

Important points: The small blade integrated into the protective casing automatically trims the newly released cutting line to the correct length to ensure optimal performance and safety. Never touch this blade during cleaning. If you only need to unwind a new length of existing line, simply press the rotary release button to release the line, then gently tap the head against the ground to unwind it.

Maintenance after use: Clean the cutting head and the device with a clean, dry cloth after each use to prevent debris buildup and line tangling issues. Only use cutting line provided by the manufacturer or equivalent quality 1.65 mm nylon line.

Question 2

Does the RYOBI RLT6130 trimmer use a single line or two cutting lines?

Accepted Answer

The RYOBI RLT6130 uses a single cutting line with a rotating head system. The line is automatically fed by a spool system integrated into the cutting head.

Here are the essential characteristics of the line:

Material: nylon line only (metal alternatives are strictly prohibited)
Diameter: according to the specifications in the manual (refer to the specifications section of your manual)
Supply: use only RYOBI branded nylon line

Your device is equipped with a small blade incorporated into the protective casing that allows for automatic cutting of the line to the appropriate length after release. Ensure that the cutting head is securely fastened and in good condition before each use.

Question 3

How to assemble the RYOBI RY18BCX26A grass trimmer?

Accepted Answer

The assembly of the RYOBI RY18BCX26A cordless trimmer is done in a few simple and quick steps.

Before you begin, remove the 18 V lithium-ion battery for safety reasons. Prepare the supplied accessories: the wrench, the washers (spring, construction, and flange), the nut, and the blade guard.

Installing the harness: First, adjust the quick-release harness so that it comfortably supports the weight of the product on your right side. Familiarize yourself with the quick-release mechanism before use - this is essential for emergency situations.

Mounting the cutting head or blade: Place the product on the ground with the blade facing up (this extends the life of the blade). Select the desired accessory: the nylon line head for the trimmer, the TRI-ARC blade for the brush cutter (max diameter 13 mm), or the saw blade (max diameter 40 mm). Secure the accessory using the flange washer, construction washer, spring washer, and the provided nut. Tighten firmly with the wrench while wearing protective gloves (the blades have very sharp edges). Ensure that the accessory is properly in place and locked before any use.

Installing the cutting line: If you are using the cutting head, locate the protective cover with the cutting blade. Open the cover of the cutting head and insert nylon line of the specified diameter (refer to the specifications table in the manual). Wind the line according to the direction indicated on the internal spool. Close the cover of the cutting head securely.

Final safety checks: Ensure that all protective elements, deflectors, and handles are properly and securely attached. Make sure that the cutting line blade in the protective cover is correctly positioned. Always remove the blade guard before use. Install the 18 V lithium-ion battery and test the device while empty before full use. The product should only be used at temperatures between 0°C and 40°C.

Question 4

Why does the line of the RYOBI RY36LT33A trimmer loosen but not cut?

Accepted Answer

If the line continuously loosens without being cut by the blade, it generally indicates a poor contact with the line cutting blade or an issue with the diameter/quality of the line used. Here’s how to diagnose and resolve:

Check the diameter and quality of the line

The manual specifies the exclusive use of nylon line with a 1.6 mm diameter. A line with a smaller diameter or of poor quality may not provide enough stiffness to be properly cut by the blade. Ensure you are using line of the exact recommended diameter.

Inspect the line cutting blade

The blade mounted on the guard (deflector) is responsible for cutting the extending line. Examine this blade:

Check that it is not worn, dull, or damaged.
Ensure there is no nylon residue or debris blocking its operation.
Gently clean around the blade (caution: it is very sharp).

Check the positioning of the line

After unwinding a new length of line, always replace the device in normal working position before turning it on. Poor positioning may prevent the line from passing correctly under the blade.

Test the operation

Start the device for a few seconds in normal mode. The extending line should be automatically cut to the correct length by the blade. If the problem persists after these checks, the blade may need replacing or the device may require further diagnosis.

Question 5

How to change the spool and cutting line of the RYOBI RY36LT33A trimmer?

Accepted Answer

Replacing the cutting line of the RYOBI RY36LT33A is a simple operation that you can perform yourself. Your trimmer has a nylon line spool (part no. 10) protected by a spool cover (part no. 9), and uses a cutting line with a diameter of 2.0 mm (part no. 11). The device is equipped with a built-in cutting line size blade (part no. 12) located at the grass deflector.

Before you begin: Disconnect the power by completely removing the battery pack. Only perform this operation on a stopped and cooled device. Use only nylon line of the specified diameter: 2.0 mm. Never use metal line or other diameters, which could damage the device or make it dangerous.

Replacement procedure:

Press the locking tabs located on the spool cover (usually on the sides) to release and remove the cover.
Remove the used or empty spool from its housing.
Install a new spool loaded with 2.0 mm nylon line, ensuring the winding direction indicated by the arrow engraved on the spool is followed.
Replace the spool cover and tighten securely until locked. Ensure that the cover is properly in place and secured.
Pull out the line so that both strands hang under the cutting head (approximate length: 10 to 15 cm).
Trim the line with the integrated cutting blade (part no. 12) located on the grass deflector at the front of the device by passing the line through the adjustment guide. You can also manually trim to equal length.

After loading: Always return the product to its normal working position before turning it back on. When using a new spool for the first time, wait a few seconds for the line to take its final position. The line will automatically adjust to the appropriate length during the first cuts thanks to the integrated cutting blade.

Important instructions: Only replace the line with nylon line provided by the manufacturer or to the exact specifications (2.0 mm). Maintenance and replacement operations must be performed carefully. If you have any doubts or if your spool is damaged, consult an authorized RYOBI service center.

Question 6

How does the line feed work on the RYOBI ONE+ RLT183225FPK?

Accepted Answer

The RYOBI ONE+ RLT183225FPK uses a cutting head with a removable line spool. Although the product manual does not explicitly detail the feed mechanism, here is how the cutting system works:

Cutting system:

Rotating nylon line (no metal blade)
A small blade mounted on the guard that automatically cuts the line to the correct length during rotation
Removable spool with cover for easy replacement or adjustment

For more precise technical details on the line diameter and the exact operation of the feed system, we recommend consulting the complete documentation from the manufacturer RYOBI or contacting an authorized dealer (for example, Leroy Merlin) who can confirm whether this model has a fully automatic or semi-automatic feed.

Question 7

How to replace the cutting line of the RYOBI One+ RY18LT33A trimmer?

Accepted Answer

Before you begin

Make sure the product is turned off and the battery is removed before any maintenance operation. Caution: the small blade attached to the housing is very sharp - do not touch it.

Replacement steps

Press the release buttons located on the side of the tool
Remove the old line spool
Insert the new spool following the indicated rotation instructions
Reassemble the tool

Type of line to use

Only use a 1.6 mm diameter nylon cutting line, compatible with RYOBI trimmers. Ensure that the diameter matches exactly what is indicated in the specifications table.

Maintenance after replacement

After each use, clean the product with a clean, dry cloth, and regularly check the condition of the line spool.

Question 8

What is the diameter of the line used in the spools of RYOBI trimmers models RLT183213, RLT1832133H, RLT183220, RLT183225, and OLT1832?

Accepted Answer

For the RYOBI trimmers models RLT183213, RLT1832133H, RLT183220, RLT183225, and OLT1832, the diameter of the line used in the spools is generally 1.6 mm.

This diameter is standard to ensure a good balance between cutting efficiency and line durability. Using a line with a different diameter could affect the performance of the device or damage the cutting head.

It is recommended to use only lines compatible with these models to ensure optimal and safe use of your trimmer.

Question 9

How to change the cutting line on a RYOBI RY18BCX26A trimmer?

Accepted Answer

To change the cutting line of your RYOBI RY18BCX26A trimmer, follow these simple steps:

1. Preparation

Make sure the device is turned off.
Remove the battery to avoid any accidental start.

2. Access the cutting head

Locate the cutting head where the line spool is located.
Open the cutting head cover by unclipping or unscrewing it depending on the model.

3. Remove the old line

Gently pull the old worn or broken line out of the spool.
If necessary, completely remove the spool to facilitate the change.

4. Prepare the new line

Use a cutting line compatible with your RYOBI model.
Cut a piece of line about 2 to 3 meters long.

5. Wind the new line

Insert one end of the line into the hole provided on the spool.
Wind the line in the direction indicated on the spool (usually clockwise).
Leave enough length sticking out so that the line can exit the cutting head.

6. Reassemble the cutting head

Replace the spool in the cutting head if you removed it.
Close and lock the cutting head cover.

7. Test the trimmer

Reinsert the battery.
Turn on the device and check that the line comes out correctly and that the cutting is effective.

By following these steps, you will be able to safely change the line of your RYOBI RY18BCX26A trimmer and maintain optimal performance.

Question 10

How to properly install the cutting line in the spool of the RYOBI RLT3525 trimmer?

Accepted Answer

To properly install the cutting line in the spool of your RYOBI RLT3525 trimmer, start by turning off the device and unplugging it from the power supply for safety reasons. Locate the two release buttons on the sides of the cutting head, press these buttons simultaneously, and gently remove the spool.

You must use exclusively 1.5 mm diameter nylon line specifically designed for the RLT3525. Cut a length of about 2 to 2.5 meters of line. The semi-automatic Bump & Feed system of your trimmer requires a regular and well-tensioned winding to function properly. Locate the small entry hole for the line on the spool and insert one end of the line into this hole.

Wrap the line around the spool in a clockwise direction, ensuring it remains tight and evenly distributed. Continue winding until about 10 to 15 cm of line is left outside the spool. Then insert the other end of the line into the retention slot provided on the spool to hold the line in place during installation.

Replace the loaded spool in the cutting head by aligning it correctly, then push it in until it clicks, indicating a secure lock. Make sure the spool is locked by gently pulling on it. Wait a few minutes before using the device to allow the line to stabilize.

Important: the RLT3525 is equipped with a built-in cutting blade in the protective cover that will automatically cut the excess line to the correct length on the first use. Never use metal line or line with a diameter different from 1.5 mm, as this would damage the semi-automatic feed mechanism and could void your 3-year warranty.

User manual RYOBI String trimmers : user manuals and guides in PDF

Models RYOBI String trimmers most viewed

Other categories RYOBI

Recent questions about String trimmers RYOBI