Q: How to use the lifting handles to cut tiles?

The RYOBI WS721S features lifting handles located on the left and right for lifting and transporting the saw. These handles should NOT be used while cutting tiles. When cutting tiles, you should: Mark the tile with a cutting line Adjust the cutting guide to the desired position Use the miter guide for diagonal or miter cuts (adjustable for all angles) Gently push the tile towards the rotating blade Keep your hands away from the cutting blade for safety reasons The lifting handles are exclusively intended for moving the saw between work areas.

Q: How to adjust and tension the chain of the RYOBI RY18PSX15A saw?

To tension the chain of your RYOBI RY18PSX15A: Adjustment Procedure Unlocking - Turn the chain guide lock button counterclockwise to unlock it. Tension Increase - Turn the chain tension button clockwise to increase tension, or counterclockwise to decrease it. Locking - Turn the chain guide lock button clockwise to lock it. Checking Correct Tension The tension is appropriate when the gap between the lower blade and the bar measures 2 to 3 mm . To check: pull the chain in the middle of the lower side of the bar down and measure the distance. If it exceeds this range, adjust the tension button accordingly. Important Maintenance Tip The chain stretches during use due to increased temperature. Check and adjust the tension frequently during the first uses and during intensive work to maintain optimal performance and your safety.

Q: Why does my RYOBI OCS1830 saw stop during use?

Initial Checks Battery - The 18V battery may be drained. Check the full charge status before each use. Chain Tension - A poorly tensioned chain can cause the motor to stop. The manual specifies checking the tension before each use. Chain Oil Level - If the oil reservoir (capacity 20-40 minutes of operation) is empty, the safety system may stop the saw. Fill it with RYOBI oil only. Braking System - Ensure that the chain brake (lever) is in the RUN position (pulled towards the front handle). If it is mistakenly in the stop position, the saw will not operate. If the problem persists Since your saw is new, this unexpected stop may be a manufacturing defect. It is covered by a 24-month warranty for private use covering all material or manufacturing defects. Procedure: Contact an authorized RYOBI service center with proof of purchase. Service is free during the warranty period. To find a center, check the RYOBI support site for your region.

Question 1

How to use the lifting handles to cut tiles?

Accepted Answer

The RYOBI WS721S features lifting handles located on the left and right for lifting and transporting the saw. These handles should NOT be used while cutting tiles.

When cutting tiles, you should:

Mark the tile with a cutting line
Adjust the cutting guide to the desired position
Use the miter guide for diagonal or miter cuts (adjustable for all angles)
Gently push the tile towards the rotating blade
Keep your hands away from the cutting blade for safety reasons

The lifting handles are exclusively intended for moving the saw between work areas.

Question 2

Why can't the chain tension adjustment knob be adjusted on my RYOBI RY18PSX15A saw?

Accepted Answer

If the chain tension adjustment knob on your RYOBI RY18PSX15A is not adjusting or is stuck, several causes may be behind this issue:

Common Causes and Solutions

Knob stuck by debris - Sawdust and dust can accumulate around the knob and prevent it from turning. Clean thoroughly with a dry brush or cloth around the knob and the guide bar.
Chain initially too tight - The knob may be difficult to turn if the chain is already excessively tight. Check that you can easily pull the chain away from the guide bar at the midpoint. If it is too tight, the knob will struggle to turn.
Temperature and thermal expansion - According to the manual, the temperature of the chain increases during normal use, causing it to elongate. After use, the chain contracts as it cools. Wait for the saw to cool completely before adjusting the knob (at least 15-20 minutes).
Knob or mechanism damaged - If the knob is visibly bent, cracked, or if rotation remains impossible after cleaning, the internal mechanism may be defective and require professional repair.

Unlocking Procedure

Completely stop the saw and wait for it to cool down.
Thoroughly clean the knob and the area of the guide bar with a dry brush.
Turn the knob slowly and gradually (no brute force) - start with a very light rotation.
If the knob turns but the tension does not increase or decrease, check that you are turning it in the right direction: clockwise to increase tension, counterclockwise to decrease it.

If the knob remains completely stuck after these checks, contact an authorized RYOBI service center as the product should not be used with a faulty tensioning system.

Question 3

How to adjust and tension the chain of the RYOBI RY18PSX15A saw?

Accepted Answer

To tension the chain of your RYOBI RY18PSX15A:

Adjustment Procedure

Unlocking - Turn the chain guide lock button counterclockwise to unlock it.
Tension Increase - Turn the chain tension button clockwise to increase tension, or counterclockwise to decrease it.
Locking - Turn the chain guide lock button clockwise to lock it.

Checking Correct Tension

The tension is appropriate when the gap between the lower blade and the bar measures 2 to 3 mm. To check: pull the chain in the middle of the lower side of the bar down and measure the distance. If it exceeds this range, adjust the tension button accordingly.

Important Maintenance Tip

The chain stretches during use due to increased temperature. Check and adjust the tension frequently during the first uses and during intensive work to maintain optimal performance and your safety.

Question 4

How do I replace the chain on my saw?

Accepted Answer

Replacing the chain on the RYOBI RY36CSX30B is an important maintenance operation. Although the PDF of this manual does not detail all the steps step by step, here are the key information:

Correct chain tension

After installation, the chain should have a gap of 4 to 5 mm between the blade and the guide. To check: pull the chain in the middle of the lower part of the guide bar and measure the distance with a ruler.

Before you begin

Turn off the saw and remove the battery for your safety
Use a new RYOBI compatible chain for this model

Manufacturer's recommendation

RYOBI strongly advises having a worn or dull chain replaced by a RYOBI authorized service center, which has the specialized tools and expertise for this operation. Replacement chains are available from an authorized RYOBI service center.

If you wish to perform the operation yourself, consult the nearest authorized service center for detailed instructions tailored to your area.

Question 5

What to do if the circular saw does not start?

Accepted Answer

If your RYOBI EMS-2026SCL circular saw does not start, first check the power presence indicator (5): if it does not light up when the saw is plugged in, the problem is with the power supply.

Checks to perform:

Check that the wall outlet is working (test with another device) and that the fuse is not blown.
Ensure that the power cord is not damaged.
Verify that the saw is plugged into an AC 230 V, 50 Hz outlet that complies with the specifications on the nameplate.
If the power indicator lights up but the saw still does not start when pressing the start button, the problem may be with the switch itself (faulty contact) or the internal motor.

Before operating the saw, also check that all safety guards (especially the lower shock-resistant plastic blade guard) are properly in place. Four holes are provided in the base to secure the saw to a workbench before use.

If all these checks do not resolve the issue, an internal or electrical motor fault requires intervention at an authorized RYOBI service center.

Question 6

Why does my RYOBI OCS1830 saw stop during use?

Accepted Answer

Initial Checks

Battery - The 18V battery may be drained. Check the full charge status before each use.
Chain Tension - A poorly tensioned chain can cause the motor to stop. The manual specifies checking the tension before each use.
Chain Oil Level - If the oil reservoir (capacity 20-40 minutes of operation) is empty, the safety system may stop the saw. Fill it with RYOBI oil only.
Braking System - Ensure that the chain brake (lever) is in the RUN position (pulled towards the front handle). If it is mistakenly in the stop position, the saw will not operate.

If the problem persists

Since your saw is new, this unexpected stop may be a manufacturing defect. It is covered by a 24-month warranty for private use covering all material or manufacturing defects.

Procedure: Contact an authorized RYOBI service center with proof of purchase. Service is free during the warranty period. To find a center, check the RYOBI support site for your region.

Question 7

How do I remove the engine cover of the RCS3535CB saw?

Accepted Answer

To access the motor and clean the fan blades and flywheel, you need to remove the starter cover by following these steps:

Position the saw on its side with the guide and chain in contact with the ground
Remove the three screws that hold the starter cover
Lift the cover and set it aside
Replace the fuel and oil caps to prevent dirt accumulation during cleaning

Important: The motor must be completely stopped before any intervention. Accumulation of debris on the motor and flywheel fins can cause dangerous overheating of the device. If you need to work on the flywheel or clutch, consult a certified technician, as some parts may break.

Question 8

Why is the chain turning in the wrong direction?

Accepted Answer

If the chain is turning in the wrong direction, the problem is due to the incorrect orientation of the chain on the chain guide.

Quick Fix

According to the manual, the direction of rotation of the chain is clearly marked under the chain guide cover (an arrow indicates the correct direction). If the chain is going the wrong way, you need to reverse the chain loop:

Stop the device and remove the battery
Loosen the locking knob of the chain guide
Rotate the entire chain loop to reverse its orientation
Ensure that the drive links properly engage in the guide rail
Wrap the chain correctly around the motor sprocket
Check that the orientation matches the arrow marked under the cover
Tighten the knob gradually

Important Tip: Also check the chain tension, which should be properly adjusted (between 4 and 5.5 mm of space measured in the middle of the lower part). Incorrect tension can give the impression that the chain is turning poorly.

Question 9

How to use the RYOBI RTBS18X electric saw?

Accepted Answer

The RYOBI RTBS18X table saw is a compact 18V battery-powered saw designed for crosscuts and ripping wood and similar materials. Here’s how to use it correctly.

Preparation and safety - Before starting, wear safety glasses, gloves, and hearing protection. Ensure your work surface is clean, clear, and stable. Familiarize yourself with the location of the on/off switch (located on top of the saw) and all safety devices, including the blade guard, splitter, and anti-kickback pawls.

Battery preparation - Check that the 18V lithium battery is fully charged before use. Insert it into the receptacle located on the side of the saw by pushing it firmly until it clicks into place. Do not force it. The battery must always be removed before any adjustments, maintenance, or storage of the saw.

Blade checking and adjustment - Ensure that the blade is properly installed, in good condition (teeth undamaged), and suitable for your material. Set the cutting depth to about 6 mm above the material to be cut using the height adjustment knob. For crosscuts, the maximum depth is 57.2 mm; for 45° bevel cuts, it is 44.5 mm. Use the rip fence for ripping (cuts parallel to the length) by placing it parallel to the blade and locking it firmly with the locking lever.

Material installation - Place your workpiece on the work table. For crosscuts, use the miter gauge to hold the wood square. For long cuts, use a push stick provided to guide the material safely without bringing your hands close to the blade. Ensure that the blade does not come into contact with any objects before starting.

Starting and cutting - Press the on/off switch to start the saw. Wait for the blade to reach full speed before starting to cut. Feed the material towards the blade steadily, without forcing. Always use the push stick or miter gauge to guide the workpiece, never your hands freehand. In case of a jam, turn off the saw immediately.

Stopping and maintenance - Once the cut is complete, release the switch and wait for the blade to come to a complete stop before removing the material. Never attempt to stop the blade quickly with a tool. Remove the battery, clean the sawdust using a brush or vacuum (no compressed air), and store the saw in a dry place. The blade may remain hot after cutting, be careful when cleaning it.

Question 10

What should I do if my Ryobi One+ RCS18X circular saw won't start even though the battery is charged and properly secured?

Accepted Answer

If your Ryobi One+ RCS18X circular saw does not start despite a charged and properly installed battery, here are several steps to check to identify and resolve the issue:

1. Check the safety button

Make sure the safety button (or lock button) is fully pressed or disabled according to the model. Some models prevent starting if this button is not activated.

2. Check the trigger

Test the trigger to ensure it is not stuck or defective. Sometimes, an internal mechanism can prevent the device from starting.

3. Test the battery on another compatible tool

Even if the battery seems charged, try using it on another Ryobi One+ tool to confirm it is functioning properly. A defective battery may not provide enough power.

4. Inspect the contacts and connections

Check that the battery contacts and those of the saw are clean, free of dust and corrosion.
Ensure there are no debris or obstructions in the connection area.

5. Listen to the motor

When you press the trigger, listen to see if the motor attempts to start (noise, vibrations). A complete absence of noise may indicate an internal electrical problem.

6. Check internal fuses or switches

If you are comfortable handling it, open the casing to check that no fuses are blown and that the internal connections are intact.

If after these checks the saw still does not start, it may be a more complex failure requiring professional repair.

User manual RYOBI Electric saw : user manuals and guides in PDF

Models RYOBI Electric saw most viewed

Other categories RYOBI

Recent questions about Electric saw RYOBI