Question 1

How to replace the motor filter of the BOSCH Serie 6 BCS61PET?

Accepted Answer

The BOSCH Serie 6 BCS61PET is equipped with a HEPA filter of the type lamella filter. According to the manual, this filter should be cleaned regularly to maintain optimal suction power, but there is no defined replacement interval.

Filter maintenance:

Tap the lamella filter over a trash can to remove dust
Rinse it with lukewarm water
Let it dry completely before putting it back in place

Filter replacement: The manual does not specify a replacement interval. If, despite regular cleaning, the suction power decreases, or if the filter appears damaged, you will need to replace it. Spare parts are available from Bosch customer service for at least 7 years. Contact Bosch service to order a new motor filter suitable for your model.

Question 2

Why is my BOSCH BGS5Z001 vacuum cleaner not suctioning or suctioning weakly?

Accepted Answer

If your BOSCH BGS5Z001 ZOO'O PROANIMAL vacuum cleaner is not suctioning well, check these points in order, as in 90% of cases, the problem comes from the pleated filter:

Step 1: Check and empty the dust container
Empty the container after each use, or at the latest when the dust reaches the level indicator. A full container drastically reduces suction power. A 3-liter dust container only filters properly if it is not saturated.

Step 2: Clean the pleated filter (priority)
This is the most common cause of loss of suction. Your model has a Sensor Control function that alerts you with a red light when cleaning is necessary. Turn off the device and turn the filter cleaning knob at least 3 times with a quick motion to activate automatic cleaning. We recommend cleaning the pleated filter before each emptying of the container. If the filter is very dirty, you can also rinse it under running water and let it dry completely before reinserting it. Caution: do not brush the filter.

Step 3: Clean the lint filter
If the Sensor Control light comes on quickly after cleaning the pleated filter, the lint filter is probably clogged. Remove the filter unit from the dust collector, then gently shake the filter or use the provided cleaning brush. If necessary, rinse it under clear water and let it dry before reinserting it.

Step 4: Clean the motor protection filter
Open the device cover and remove this filter. Clean it by tapping it on the edge of a container or rinse it under water if very dirty, then let it dry completely before reinserting it.

Step 5: Check that no hose is blocked
Visually inspect the suction hose, tube, and accessories (TURBO-UNIVERSAL brush, nozzle) for any blockages or hair entangled. Remember to lift the brush if it struggles to pick up dirt.

Step 6: Check the power setting
Make sure the power regulator is not in “Low” mode (reserved for delicate fabrics). For floors and carpets, use “Medium” or “High” mode. The power level indicator shows you the active mode.

If the power remains weak after following all these steps, contact BOSCH customer service. For optimal cleaning results, maintain regular hygiene of your device, especially by cleaning the HEPA filter or the air outlet filter after 1 year of use.

Question 3

How to use the descaling and cleaning function on the BOSCH Serie 8 VarioComfort TDS8060DE iron?

Accepted Answer

The BOSCH Serie 8 VarioComfort TDS8060DE iron has an automated descaling function called "Calc'nClean". A "Calc'nClean" indicator light (3) flashes and three beeps sound to alert you that descaling is necessary. You can continue ironing, but you must perform the descaling process before the next use, when the device is cold.

Descaling the boiler:

Ensure the device is cold and unplugged.
Empty the water tank.
Remove the iron from the iron rest.
Unscrew and remove the boiler cap (9) and empty it completely.
Fill the boiler with about 300 ml of tap water, close the cap, and shake the base for a few moments, then empty completely. Repeat this process twice for better results.
If your device has a limescale filter (9*), rinse it under tap water until the limescale residues disappear.
Replace and tighten the cap.

Descaling the iron:

Fill the tank (10) with tap water and plug in the device.
Press the power button (2).
Press the descaling button (3) for 2 seconds. Its indicator light stays on.
Wait until the indicator light (2) stops flashing and stays on. Two beeps will sound.
Hold the iron horizontally above an empty sink to collect the water. If your device has a "Calc'nClean" collection tank (18*), place the iron above it.
Press the steam release button (14) for 2 seconds. The process starts automatically. Boiling water and steam will escape from the soleplate, containing limescale and deposits. Beeps will sound every 5 seconds.
After about 3 minutes, the iron stops emitting steam and a long beep indicates the end of the process. The device will turn off automatically.
Clean the soleplate (17) by immediately wiping away any residue by passing the hot iron over a damp cotton cloth.

Regular cleaning of the device:

If the device is slightly dirty, wipe it with a damp cotton cloth and dry it.
Avoid contact with metallic objects and never clean the soleplate with an abrasive sponge or chemicals. If a synthetic fabric has melted onto the soleplate due to excessive temperature, turn off the steam and rub the residue with a damp cotton cloth folded several times.

Question 4

How to change the cutting head of the BOSCH AFS 23-37 brush cutter?

Accepted Answer

To change the cutting head of your BOSCH AFS 23-37 brush cutter, follow these simple steps:

1. Preparation

Ensure that the brush cutter is turned off and unplugged to avoid any risk of accident.
Place the device on a stable surface.

2. Removing the worn cutting head

Use an appropriate wrench (often a flat wrench or an adjustable wrench) to unscrew the nut that holds the cutting head.
Once the nut is removed, gently pull the worn cutting head to detach it from the thread.

3. Installing the new cutting head

Position the new cutting head on the thread.
Screw the fastening nut tightly using the wrench, ensuring it is securely tightened for safety during use.

By following these steps, you will be able to effectively replace the cutting head of your BOSCH AFS 23-37 brush cutter and continue your gardening tasks safely.

Question 5

How to attach the basket to the BOSCH ROTAK 37 lawn mower?

Accepted Answer

To properly attach the basket to your BOSCH ROTAK 37 lawn mower, follow these simple steps:

Position the basket: Bring the basket close to the mower, aligning its supports with those located at the back of the machine.
Insert the basket: Gently slide the basket into the designated supports. You should feel a slight resistance or hear a click indicating that the basket is securely in place.
Check the attachment: Ensure that the basket is firmly attached and does not move. This guarantees optimal collection of the cut grass during mowing.

If the basket does not attach easily, check that the supports are not damaged or obstructed by debris. Proper maintenance makes it easier to attach the basket.

Question 6

What should I do if my BOSCH GSV29VWEV refrigerator does not start?

Accepted Answer

If your BOSCH GSV29VWEV refrigerator does not start, here are several steps to check to identify and resolve the issue:

1. Check the power supply

Make sure the refrigerator is properly plugged into a working outlet.
Test the electrical outlet with another device to confirm it is functioning.
Check that the power cord is not damaged or cut.

2. Check the thermostat

Ensure that the thermostat is set to an appropriate temperature (not on "0" or a temperature that is too high).
A misadjusted thermostat can prevent the compressor from starting.

3. Inspect the electrical protections

Check that the circuit breaker or fuse has not tripped or blown.

4. Listen for sounds

When powered on, listen for any noise from the compressor or fans.
The complete absence of sound may indicate an electrical issue or an internal fault.

5. Possible defrosting

Excess frost can block operation. In this case, unplug the refrigerator and let it defrost for several hours.

If after these checks the refrigerator still does not start, it is likely that a technical intervention is necessary to diagnose a possible fault in the compressor, thermostat, or other internal components.

Question 7

How to remove the brush from the BOSCH Serie 6 BCS61PET vacuum cleaner?

Accepted Answer

To remove the brush from your BOSCH Serie 6 BCS61PET vacuum cleaner, follow these simple steps:

Turn off and unplug the vacuum cleaner to ensure your safety during handling.
Locate the brush at the bottom of the device, usually attached to the end of the tube or the main body.
Identify the fastening mechanism: it may be a button, lever, or clip that holds the brush in place.
Operate this mechanism by pressing, pulling, or unlocking depending on the model.
Gently pull the brush outward to detach it. Avoid applying excessive force to prevent damaging the parts.

This operation will allow you to easily clean or replace the brush, thus contributing to optimal maintenance of your vacuum cleaner.

Question 8

How to clean the brush of the BOSCH Serie 6 BCS61PET vacuum cleaner?

Accepted Answer

To properly clean the motorized brush of your BOSCH Serie 6 BCS61PET cordless vacuum cleaner, follow these simple yet essential steps that will ensure optimal performance and a prolonged lifespan for your device.

Preparation and safety
Before you begin, make sure the device is completely turned off. Then disconnect the nozzle from the rest of the vacuum cleaner by separating it from the suction tube. This step is crucial for properly accessing the motorized brush.

Removing the motorized brush
Once the nozzle is disconnected, locate the locking mechanism of the brush. Release the brush roller by unlocking this mechanism, then remove the roller laterally from the nozzle. This delicate operation should be performed carefully to avoid damaging the components.

Cleaning hair and debris
Use a pair of scissors to cut the threads, hair, and fibers wrapped around the brush. Once the hair is cut, remove it completely. This is the key step to eliminate blockages and restore the suction performance of your BCS61PET. Please be careful not to damage the bristles of the brush with the scissors.

Reassembling the brush
After cleaning, insert the brush roller laterally along the guiding bar of the nozzle. Ensure that the brush is properly positioned in its housing, then lock it by activating the locking mechanism. Then reconnect the nozzle to the vacuum cleaner, ensuring that it clicks into place correctly.

Checking operation
Before reusing your vacuum cleaner, plug it in and turn it on to check that the motorized brush is spinning correctly and without abnormal noises. If you notice reduced suction power even after cleaning the brush, remember to also clean the HEPA filter and the dust container, which can also affect the performance of your BCS61PET.

Regular maintenance of the brush ensures better suction on all types of surfaces (carpets and hard floors) and significantly prolongs the lifespan of your Bosch cordless vacuum cleaner.

Question 9

How to change the spool of the BOSCH ART 23 COMBITRIM trimmer?

Accepted Answer

To change the wire spool (cartridge) of your BOSCH ART 23 COMBITRIM trimmer, first turn off the device and unplug it from the power outlet for your safety.

Removing the old spool: Firmly hold the spool plate 23 in position. Turn the spool cover 21 counterclockwise and remove it. Extract the empty spool 25 from the cover.

Installing the new spool: Thread the wire of the new (or filled) spool through hole 22 and place it in the spool cover 21. Pull about 9 cm of wire out of the spool to allow for proper advancement. Position the spool correctly with its cover on the spool plate (bayonet closure), press lightly and turn the cover fully to the right until it clicks into place.

For extra-strong cutting wire: if you are using a spool with extra-strong wire, the assembly is identical. Hold the spool plate 23, remove the cover 21, insert the spool with extra-strong wire 14 in the correct position and tighten by turning clockwise until it clicks.

Important point: exclusively use original Bosch cutting wires. These specially designed wires offer optimal cutting and advancement characteristics. Other cutting wires have lower working power and may damage your device.

Question 10

How to replace part 43/6 on a BOSCH AdvancedRotak 36950 lawn mower?

Accepted Answer

Part 43/6 of your BOSCH AdvancedRotak 36950 lawn mower is the activation button (start button), referenced under Bosch number 1600A022AC. This button is located on the handle of the device and is used to start the engine. Its replacement is an operation that must be carried out with caution, strictly following safety instructions.

Preparation and safety: Before any intervention, completely stop the mower, unplug and remove the isolator switch from its position, then remove the battery. Cutting off the power is essential as the blade continues to spin for a few seconds after the engine stops. Wear gardening gloves throughout the operation. Wait a few minutes for the engine to cool down completely before starting the replacement.

Locating and accessing the part: The button 43/6 is located on the upper handle of your lawn mower. You will need to access the inside of the handle casing to reach this component. Refer to the exploded diagram in your manual to accurately identify the exact position. You can also refer to the technical plans available at www.bosch-pt.com, which list all the spare part numbers for your model 3600HB9901.

Removing the old button: Use a suitable screwdriver (usually Phillips) to unscrew the elements of the handle that hold the button in place. Be careful not to lose the small fastening parts. Once the screws are removed, gently free the defective button from the casing. There may be electrical connections (wires or connectors) attached to the button, note their exact position before disconnecting them to facilitate reassembly.

Installing the new part: Place the replacement button 1600A022AC into the casing, ensuring it is oriented correctly. Reconnect all wires or electrical connectors in the same order as before, then secure the button with the original screws, tightening them firmly but not excessively to avoid damaging the plastic casing of the handle.

Finishing and checking: Fully reassemble the handle and all components you had to disassemble. Reinsert the isolator switch into its place, then put the battery back in. Before starting to mow, test the start several times to ensure the new button works correctly. The device should respond immediately to each press of the button, without hesitation or failure.

Important: If no LED lights up after pressing the new button, or if the mower still does not start, the problem may be a more serious electrical issue. Consult one of the authorized Bosch after-sales services listed in your manual. You can order this replacement part from specialized Bosch spare parts distributors or directly from Bosch service (delivery time: 1 to 4 weeks). The unit cost of this button is approximately 2 euros excluding VAT.

User manual BOSCH : user manuals and guides in PDF

Models BOSCH most viewed

Browse manuals BOSCH by appliance type

Recent questions about devices BOSCH