User manual BOSCH Air conditioner : 32 free PDF user manuals

Q: What is the COP (Coefficient of Performance) of the BOSCH REKM 215 air conditioner?

The COP (Coefficient of Performance) of the BOSCH REKM 215 is not explicitly stated in the manual. However, you can easily calculate it from the specifications in the manual: Cooling power: 2,600 W Electric consumption: 1,180 W This gives a COP of approximately 2.2 , which means that the air conditioner produces 2.2 units of cooling for each unit of electrical energy consumed. This is typical energy efficiency for a portable air conditioner of this category. For more details on energy efficiency or the exact EU efficiency class of your device, you can refer to the energy label attached to your unit or contact BOSCH technical support directly.

Q: How to install and remove the air exhaust hose outside?

Installation of the air exhaust hose To install the air exhaust hose of your BOSCH PAM 0320 air conditioner: Initial connection : Place the air evacuation tube into the connector with the "push" tab and screw it to the left until it is securely fastened. Installation of the diffuser : Place the diffuser at the free end of the tube by gently pressing both parts until you hear a "click". Ensure that the closure clips are properly closed. Window exit : Slightly open the window, insert the diffuser between the sash and the frame, then close the window as much as possible. Use the provided suction cup to hold it in place. Important points: Maximum hose length: 140 cm Position the hose above the unit for optimal efficiency Avoid excessive bends that would reduce airflow Ensure that the diffuser is properly clipped before inserting it into the window

Q: Why is the condensed water not draining outside on my BOSCH REKM 215 air conditioner?

If the condensed water is not draining outside of your BOSCH REKM 215 air conditioner, several points need to be checked: Drainage Pipe Checks Check that the pipe is properly connected - The drainage pipe located at the bottom of the unit must be securely attached. A poor connection prevents water from escaping. Inspect the length of the pipe - On the REKM 215, the maximum allowed length is 140 cm. A pipe that is too long can block water circulation. Check the outlet height - The pipe should end at least 70 cm above the ground to allow for effective gravity drainage. Look for clogs - Ensure that the pipe is not obstructed by debris, limescale deposits, or dust. Clean it gently with warm water if necessary. Avoid sharp bends - Too sharp curves in the pipe's path reduce drainage efficiency. Prefer wide and gradual curves. Internal Tank Checks Safety indicator - A light turns on when the internal tank reaches its maximum level. If this light is on, you need to manually empty the water (the simple drainage mode uses the pipe located at the bottom of the unit). Dehumidification mode - If you are using the dehumidification mode with a dedicated container, ensure that it is properly in place and check that it is not overflowing. The REKM 215 can accumulate up to 30 liters of water in 24 hours depending on the ambient humidity. If after these checks the water still does not drain, a malfunction of the internal system may be the cause and requires technical intervention.

Q: How do I set the humidity percentage on the BOSCH Climate 3000i?

The BOSCH Climate 3000i does not offer a humidity percentage setting . In dehumidification mode, only the temperature parameter is adjustable. To activate dehumidification: Press the Mode button several times until you see the symbol (≈) on the screen Use the directional buttons to set the temperature: ∧ button: increase ∨ button: decrease The fan operates automatically in dehumidification mode and cannot be manually adjusted.

Q: What to do after selecting the dehumidification mode on the BOSCH Climate 3000i?

After activating the dehumidification mode, here are the steps to follow: Adjust the temperature Use the ∧ (up arrow) button to increase the temperature Use the ∨ (down arrow) button to decrease the temperature Let it run In dehumidification mode, the fan speed is fully automatic and cannot be adjusted manually The air conditioner will immediately start dehumidifying the ambient air Important points to remember The Follow Me function is not available in dehumidification mode If you turn off the device, the dehumidification mode will not be saved - you will need to reactivate it when you turn it on next time That's it! Your BOSCH Climate 3000i is now operating in dehumidification mode with the temperature you have chosen.

Q: Do I need to reactivate the dehumidification mode every time I turn on the BOSCH Climate 3000i?

Yes, you need to select the dehumidification mode every time you turn on your BOSCH Climate 3000i air conditioner. This setting is not saved between restarts. How to activate the dehumidification mode Press the Mode button on the remote several times until the screen displays the dehumidification symbol (≈) Set the desired temperature using the ∧ (increase) and ∨ (decrease) buttons Note that the fan speed is not adjustable in dehumidification mode - it remains automatic Important: In dehumidification mode, some functions are not available, including the Follow Me function (temperature measurement on remote) and the reduced mode (energy saving).

Q: How to activate the Follow Me function on the BOSCH Climate 3000i?

The Follow Me function of the BOSCH Climate 3000i is configured from the remote control. Here are the steps: Press the Set button to access advanced functions Navigate with the ∧/∨ (arrow) buttons to the Follow Me icon Press OK to confirm and activate the function Once activated, the Follow Me function measures the ambient temperature near your remote control every 3 minutes. It only works in Cooling, Heating, or Auto modes (not in Dehumidification or Ventilation mode). The temperature displayed on the remote control will then be that of your location, while the indoor unit continues to display that of its installation point - this difference is normal and intentional.

Q: What symbol represents the Set button on the BOSCH Climate 3000i remote control?

The Set button on your BOSCH Climate 3000i remote control is identified by the symbol = (three horizontal lines). You will find it directly next to the OK button. This Set button allows you to access the configuration menus and advanced functions of your air conditioner, including: Navigating through the settings with the directional keys (∧/∨) Enabling or disabling functions such as Silent Mode, Turbo, or Follow Me Setting the timer, programming hours, and other advanced options To use the Set: press the = button, use the arrows to navigate to the desired function, and then confirm with OK .

Q: Where is the Set button on the BOSCH Climate 3000i remote control?

The Set button on your BOSCH Climate 3000i remote control is used to access extended functions and confirm your advanced settings selections. If you do not see it immediately on your remote control: Check the layout : depending on your model variant, the Set button may not be located where you expect it. Look for a button typically located in the center or near the main control buttons (OK, Mode, On/Off). Labeling may vary : on some variants, the button may not have a visible label or may simply be marked with a small inscription. Function of the button : the Set button opens access to advanced settings and allows you to validate changes to temperature, fan speed, timer, turbo, automatic cleaning, or other specialized functions. If you have a remote control variant with a very different layout, refer to the button diagram in the PDF of this manual (it shows up to three possible variants with all button positions). If you still cannot find the Set button after checking all variants, try the button in the center of your directional pad or the main confirmation button (OK) - it often serves a similar function.

Q: Why is the temperature displayed on the indoor unit different from that of the remote control?

This temperature difference is normal and intentional , especially when you have activated the Follow Me function on your BOSCH Climate 3000i. Indeed, the remote control measures the temperature at your actual location in the room every 3 minutes, while the display of the indoor unit shows the temperature measured at the location where it is fixed. These two areas may have slightly different temperatures depending on the characteristics of your room (sunlight, air circulation, insulation, etc.). The Follow Me function deliberately uses the temperature from the remote control to adjust the air conditioner to your current position, which explains why the display shows a different value than that shown on the remote control. If the difference seems too significant or abnormal: Check that the Follow Me function is enabled (press Set , select the corresponding icon with the directional keys, then confirm with OK ) Make sure you are not in dehumidification or fan mode, where Follow Me does not operate Wait at least 3 minutes after activation for synchronization to occur This behavior is completely normal on the BOSCH Climate 3000i and confirms that your remote control effectively manages the temperature of your personal space.

Models BOSCH Air conditioner most viewed

User manual BOSCH Air conditioner : user manuals and guides in PDF

Models BOSCH Air conditioner most viewed

Other categories BOSCH

Recent questions about Air conditioner BOSCH