User manual BOSCH Saw : 217 free PDF user manuals

Q: How to insert a blade into the BOSCH GST 700?

To insert a blade into your BOSCH GST 700, follow these steps: Preparation Clean the blade base (shank) before installation. A dirty base cannot be securely fixed. Blade Installation Insert the saw blade (11) into the blade holder (9) until it clicks Check that the teeth are oriented in the direction of the cut Ensure that the back of the blade rests correctly in the groove of the guide roller (10) Verification Confirm that the blade is properly fixed and tightened before any use. A poorly fixed blade is dangerous. Safety Wear protective gloves when handling, as the blades are sharp Blades can be very hot after prolonged use Only use T-shank blades on this device To remove the blade, simply slide the blade holder (9) upwards as indicated in the manual and remove the blade.

Q: How to lubricate and maintain the transmission of the BOSCH PROFESSIONAL GSA 18V-LIC jigsaw?

The manual for the GSA 18V-LIC recommends maintaining the functionality of the blade holder using appropriate lubricants. Here’s how to proceed: Blade Holder Maintenance Stop the tool and lock the power switch before any intervention Remove the saw blade Clean the blade holder with compressed air or a soft brush to remove debris Apply an appropriate lubricant to the blade holder to ensure proper functionality General Maintenance Regularly clean the ventilation slots with a dry brush Avoid sawing very dusty materials in the inverted position to reduce dust accumulation Important: The manual does not detail the lubrication of internal gears. User maintenance is limited to accessible external components like the blade holder. For maintenance of internal elements or transmission repair, consult Bosch service.

Q: What is the sound level in dB of the Bosch GTS 70-216 Professional?

The sound level of the Bosch GTS 70-216 Professional is: Sound pressure level: 90 dB(A) Sound power level: 105 dB(A) Uncertainty: K = 3 dB These values are listed in the official technical specifications of the manufacturer's manual. Important for safety: With a sound pressure level of 90 dB(A), it is mandatory to wear hearing protection (earplugs or earmuffs) when using the saw. This noise level can cause hearing damage with prolonged exposure. Also, remember to use the provided safety push stick and to strictly follow the safety instructions in the manual for safe operation.

Q: How do I reattach the adjustable depth lever that has come off?

The adjustable depth lever of your BOSCH CS20 saw is designed to be easily removed and readjusted. Here’s how to reattach it: Reattachment Procedure Unplug the saw before any intervention Align the lever with its attachment point on the housing Press firmly on the lever until it clicks into place Test the operation : pull the lever outward - it should move freely and lock when you push it back Depth System Your saw features a preset ratchet system that automatically stops the base at four standard depths: 2 inches 3/4 inch 1/2 inch 1/4 inch To adjust the depth correctly: pull the lever outward, place it in the desired position, then push it back to lock it. Remember that the blade should not extend more than the length of a tooth from the back of the piece to minimize chipping. If the lever does not click into place properly after reinsertion, the internal mechanism may be damaged and would require a replacement part. Please refer to the manual for BOSCH support contact information.

Q: How to replace or change the saw blade of the BOSCH GCM 10 SD Professional?

How to replace the saw blade Before you begin: Unplug the tool from the power supply and allow the blade to cool completely after use. Wear protective gloves. Removing the old blade Press the locking lever 3 and tilt the protective guard 4 back to the stop Unscrew the screw 37 with a Phillips screwdriver (be careful of the preload) Pull the protective guard 4 completely back Unscrew the hex head screw 39 with the hex key 36 (opening 13) Press the spindle lock 38 until it clicks Remove the flange 40 and the blade 5 Installing the new blade Place the new blade on the spindle 41 , respecting the indicated direction of rotation Install the flange 40 and the screw 39 Press the spindle lock 38 and tighten the screw with a torque of 15-23 Nm Push the protective guard 4 forward Re-screw the screw 37 Specifications of compatible blades Diameter: 254 mm (10 inches) Bore: 30 mm or 25.4 mm depending on variant Required maximum speed: Minimum 4500 min⁻¹ Standard: EN 847-1 (do not use HSS blades) Reference example: 2 608 640 438 (40 teeth, bore 30 mm)

Q: How to adjust the cutting depth on the Bosch GKS 55 circular saw?

To adjust the cutting depth on your Bosch GKS 55: Loosen the locking lever (27) located on the side of the saw to allow vertical movement Adjust the depth by moving the saw: Move the saw away from the base plate (14) to reduce the depth Bring it closer to the base plate to increase the depth Set the desired measurement using the depth scale (28) visible on the side of the saw Tighten the locking lever (27) to secure the adjustment Important tip: To optimize safety and cutting quality, ensure that only part of a tooth of the blade is visible under the workpiece. Tip: If the lever gets stuck during adjustment, alternate moving it down and then up until you achieve the desired lock.

Q: Where is the knob to adjust the vertical angle of the saw?

The adjustment button (21) for adjusting the tilt angle (vertical) of the GCM 254 D Professional is located on the body of the machine, near the base of the tool arm. It is a small rotary button that allows you to release the 0° angle in order to select other tilt angles. It should be turned only slightly. To set a custom tilt angle, proceed as follows: pull the locking button (13) upwards to release the lock. Turn the adjustment button (21) slightly to the left to disengage the 0° angle. Then, tilt the tool arm to the desired angle using the handle (5) . Check your exact angle by reading the angle indicator (55) against the graduated scale (56) . Finally, push the locking button (13) downwards to lock the selected angle. The saw offers four standard tilt angles that are easily accessible: 0°, 22.5°, 33.9° and 45° (to the left or to the right). To use these standard stops (41), first remove the adjustable stop on your side (19), then rotate the standard stop (41) corresponding to the desired angle until it clicks into place at the marking arrow. Then pull the locking button (13) upwards and let the tool arm tilt to the stop on your side, or use the handle (5) to bring it to the stop on the other side. The total tilt angle can be adjusted from 45° to the left to 45° to the right. The angle indicator (55) and the graduated scale (56) continuously display the current angle, allowing for very precise adjustments. After each adjustment, always check that the saw blade does not touch the adjustable stops or clamps before starting to saw.

Q: How to unlock and adjust the vertical angle of the saw?

To adjust the vertical angle of your BOSCH GCM 254 D Professional: Adjustment Steps Release the mechanism : Pull the locking button (13) upwards to unlock the arm. Set the angle : Tilt the tool arm to the desired angle using the handle (5). You can check your position using the angle indicator (55) on the graduated scale (56). Lock the position : Push the locking button (13) downwards to secure the chosen angle. Available angles: The saw allows adjustments from -45° to +45°, with standard stops at 0°, 22.5°, 33.9°, and 45°. If the locking button remains stuck: Check that it is properly released and that no obstacles are hindering the movement of the arm. The adjustment button (21) should also turn freely.

Q: How to adjust the cutting depth on the BOSCH GCM 800 SJ saw?

The cutting depth on the BOSCH GCM 800 SJ saw is not an adjustable parameter. It is automatically determined by the thickness of the piece you place under the blade. The saw is capable of cutting up to a maximum depth of 70 mm at neutral angles (0°/0°). The actual cutting depth depends on: The thickness of your material : The thicker the piece, the greater the cutting depth will be, up to a maximum of 70 mm. The bevel and miter angle : When you set cutting angles (bevel or miter), the maximum available depth decreases depending on the chosen angle. To prepare your BOSCH GCM 800 SJ saw before cutting, ensure that your material is properly positioned and held firmly against the guides (barrier 6 and 21) according to the permitted dimensions (maximum thickness of 70 mm). There is no lever or knob to adjust the cutting depth: this parameter adjusts automatically based on your piece. If you need a cutting depth greater than what your current piece allows, you will need to use a thicker material or consider a different cutting approach suited to your dimensional constraints.

Q: Which replacement blades are compatible with the BOSCH PROFESSIONAL GSA 18V-LIC saw?

The BOSCH PROFESSIONAL GSA 18V-LIC saw is compatible with several types of replacement blades suitable for different materials and uses. Here are the main categories of blades you can use: Compatible blade types Wood blades: Designed for fast and precise cuts in soft or hard wood. They typically have wide teeth for effective sawing. Metal blades: Suitable for cutting metals, these blades have fine teeth and are made of hardened steel or bi-metal for better durability. Plastic blades: Specifically designed to cut various types of plastics cleanly without splintering. Bi-metal blades: These blades combine flexibility and durability, ideal for cutting multiple materials, including wood with nails or light metals. Tips for choosing your blades Always check that the blade is compatible with the mounting system of the GSA 18V-LIC (SDS system or other depending on the model). Choose the blade based on the material to be cut to optimize cutting quality and blade lifespan. Prefer blades from recognized brands or those recommended by BOSCH to ensure safety and performance. In summary, you can use a wide range of replacement blades suitable for your BOSCH PROFESSIONAL GSA 18V-LIC saw, provided they are compatible with its mounting system and suitable for the material to be cut.

Models BOSCH Saw most viewed

User manual BOSCH Saw : user manuals and guides in PDF

Models BOSCH Saw most viewed

Other categories BOSCH

Recent questions about Saw BOSCH