Question 1

How to connect an external DVD player to the Yamaha RXV657 amplifier?

Accepted Answer

To connect an external DVD player to your Yamaha RXV657 home theater amplifier, follow the steps below:

1. Connecting video signals

Prefer the COMPONENT VIDEO cable (Y, Pb, Pr jacks) located at the back of the amplifier for optimal quality.
If the DVD player does not have a component output, you can use the S-VIDEO jack or the composite VIDEO jack (yellow jack).

2. Connecting audio signals

For analog audio, connect the RCA AUDIO jacks (red and white) between the DVD player and the amplifier.
For better sound quality, use the digital audio inputs: either COAXIAL (digital coaxial cable) or OPTICAL (optical cable).

3. Important notes

If you connect both COAXIAL and OPTICAL digital inputs simultaneously, the amplifier will prioritize the COAXIAL signal.
After making the connections, select the DVD source on your amplifier to listen to and view your DVD player.

This method ensures an optimal connection between your DVD player and the Yamaha RXV657 amplifier, thus providing audio and video quality suitable for your home theater setup.

Question 2

How to connect headphones to the Yamaha RXV657 amplifier?

Accepted Answer

To connect headphones to your Yamaha RXV657 amplifier, simply insert the 3.5 mm jack plug of your headphones into the PHONES jack located on the front panel of the device.

When you plug in the headphones, the behavior of the RXV657 automatically changes. The sound is immediately cut off from the main speakers and the PRE OUT outputs. All Dolby Digital and DTS audio signals are automatically mixed in stereo to be compatible with your headphones, allowing you to fully enjoy surround content privately.

The SILENT CINEMA function automatically activates when you plug in the headphones AND listen to a sound field program (CINEMA DSP or HiFi DSP). The SILENT CINEMA indicator lights up on the front display to confirm its activation. Note that this function does not activate if you are using the PURE DIRECT mode or the 2-channel stereo selection.

You have independent controls to optimize headphone listening. The TONE CONTROL settings (bass and treble) for the headphones are saved separately from those of the speakers. You can also adjust the bass (LFE) level and dynamic compression specifically for the headphones via the setup menu, which is particularly useful if you regularly listen at low volume.

To stop headphone listening, simply unplug the headphones. The sound automatically returns to the speakers and PRE OUT outputs according to your previous configuration. A Headphones indicator lights up on the front of the device to show you that headphones are connected.

Question 3

What should I do if my Yamaha MXA5000 receiver does not turn on?

Accepted Answer

If your Yamaha MXA5000 receiver does not turn on, here are several steps to follow to identify and possibly resolve the issue:

1. Check the power supply

Make sure the power cable is securely connected to both the receiver and a functional wall outlet.
Test the electrical outlet by plugging in another device to verify that it is working properly.

2. Check the power switch

Ensure that the power switch located at the back or side of the device is in the ON position.

3. Overload protection mode

If the receiver has experienced an electrical overload or overheating, it may be in protection mode.
Unplug the device from the electrical outlet, leave it disconnected for about 5 to 10 minutes, then plug it back in and try to turn it on again.

4. Check cables and connections

Inspect all cables connected to the receiver for any damage or poor connections.
Replace any damaged cables and ensure that all connections are secure.

5. Check the temperature

If the receiver is warm to the touch, it may be overheating.
Allow it to cool down in a well-ventilated area before attempting to turn it on again.

If after these checks your Yamaha MXA5000 still does not turn on, there may be an internal issue requiring specialized technical intervention.

Question 4

How to properly connect the YAMAHA R-S300 audio receiver?

Accepted Answer

Before connecting your YAMAHA R-S300 audio receiver, place it on a stable, dry, and well-ventilated surface. Leave at least 30 cm of space above and 20 cm at the back and sides to ensure proper ventilation. Keep it away from heat sources, moisture, and electrical devices that may cause humming. Important: never plug the device into the power supply before all connections between components are completed.

Connecting the speakers - At the back of the receiver, you will find the SPEAKERS A and SPEAKERS B terminals. Start by setting the IMPEDANCE SELECTOR switch (on the back panel) according to the impedance of your speakers: HIGH position if your speakers have an impedance of 8 Ω or more (or 16 Ω if you are using two pairs simultaneously), LOW position if the impedance is 4 Ω or more (or 8 Ω for two pairs). Then, connect the speaker cables, strictly observing the polarity: the red wire (or white stripe) should connect to the red terminal (+), and the black wire to the black terminal (-). Make sure to tighten the connections well and avoid leaving any bare wires touching, which could damage the device.

Connecting audio sources - You can connect several types of audio equipment according to your needs. Use the appropriate RCA connectors: PHONO inputs for a turntable (also connect the GND ground wire from the turntable), CD inputs for a CD player, LINE 1-2 inputs for any external audio component (MP3 player, DVD player, etc.). If you have a powered subwoofer, connect it to the SUBWOOFER OUT jack, which automatically filters signals above 90 Hz. For an iPod or Bluetooth system, use the designated DOCK connector.

Connecting FM/AM antennas - The included kit contains an indoor FM antenna and an AM loop. Connect the FM antenna to the FM terminal (you can place it near the receiver) and the AM loop to the AM terminal, positioning it away from the main unit. Adjust the FM antenna for the best reception. If the reception quality is insufficient, you may opt for outdoor antennas (consult an authorized Yamaha dealer).

Connecting the power supply - Once all connections for speakers, sources, and antennas are made, plug the power cable into a functional and secure wall outlet (AC 230 V, 50/60 Hz). After plugging in, press the power button (A) located on the front panel to turn on the receiver.

Final check - Visually check that all connectors are tight and that no wires are damaged. Turn on the receiver and test the sound by sequentially selecting each audio source via the INPUT selector on the front panel or the remote control. Gradually adjust the volume and ensure that the sound is coming correctly from both speakers with good quality. The BASS and TREBLE controls on the front panel will allow you to adjust the sound quality according to your preferences. If you have sound issues, check the polarity of the speaker cables again and ensure that the IMPEDANCE SELECTOR switch matches your speakers.

User manual YAMAHA Home cinema amp : user manuals and guides in PDF

Models YAMAHA Home cinema amp most viewed

Other categories YAMAHA

Recent questions about Home cinema amp YAMAHA