Q: How do I turn off the SHARP EL-2607PG calculator?

The SHARP EL-2607PG is equipped with a multi-function power switch located at the top of the device. To turn off the calculator , simply set the selector to "OFF" . This switch has several operating positions: "•" : power on in non-printing mode "P" : power on in printing mode "P•IC" : power on with printing and item counting "OFF" : complete shutdown of the device The calculator requires AC power supply (220V-230V, 50Hz) to operate, so turning it off via this switch completely interrupts the power supply.

Q: How do I remove the error message 'E' from the screen of the SHARP EL-1750PIII calculator?

The message 'E' displayed on your SHARP EL-1750PIII indicates a capacity overflow or an error . Here’s how to remove it: Possible causes: The result exceeds 12 digits The memory exceeds 12 digits Division by zero To clear the error: Press the decimal point key , then press 9/CE to clear the error. The contents of the memory will be retained - you just need to clear the error state and continue your calculations.

Q: How to perform a simple subtraction with the SHARP EL-2901RH?

To perform a simple subtraction on your SHARP EL-2901RH calculator, follow these steps: Make sure the calculator is turned on by setting the switch at the bottom left to P (print mode) Press CE (Clear Entry) to reset the display and clear the last operation Enter the first number (the number you want to subtract from) Press the - (minus) key, located to the right of the numeric keys Enter the number to subtract (the second number) Press = to get the result, which will be displayed and printed automatically Concrete example: To calculate 50 - 12, do: 50 → (press -) → 12 → (press =) → Result: 38 Addition mode (decimal switch in position A): If you set the decimal switch to A , the decimal point is automatically placed on the 2nd digit from the right. This allows for subtractions of amounts without having to enter the decimal point manually, which is very useful for money operations (example: 50.00 - 12.00 to calculate directly without entering the point). Tip in case of error: If you make a mistake entering a digit before pressing the subtraction key, press CE to cancel the entry and start the operation again. If the error occurs after the first number, you can also press C to completely clear and start from zero. Printing the result: When the switch is in P mode (printing), each operation is automatically printed on the 57-58 mm wide paper roll. The result of your subtraction will be printed with the asterisk symbol to indicate the final total. The mechanical printer displays about 2.1 lines per second.

Question 1

How to use the CM and RM keys on the SHARP EL1611P?

Accepted Answer

The SHARP EL1611P calculator has two important keys for managing memory:

CM - Clear Memory: press this key to completely delete the value currently stored in memory.
RM - Recall Memory: press this key to display and retrieve the previously stored value.

The memory works with the complementary keys M+ and M-, respectively for adding to memory and subtracting from memory. Thus, the typical cycle is: enter a number, press M+ (or M-) to store it, then use RM to recall it later, and CM to clear.

Question 2

How do I turn off the SHARP EL-2607PG calculator?

Accepted Answer

The SHARP EL-2607PG is equipped with a multi-function power switch located at the top of the device. To turn off the calculator, simply set the selector to "OFF".

This switch has several operating positions:

"•": power on in non-printing mode
"P": power on in printing mode
"P•IC": power on with printing and item counting
"OFF": complete shutdown of the device

The calculator requires AC power supply (220V-230V, 50Hz) to operate, so turning it off via this switch completely interrupts the power supply.

Question 3

How do I remove the error message 'E' from the screen of the SHARP EL-1750PIII calculator?

Accepted Answer

The message 'E' displayed on your SHARP EL-1750PIII indicates a capacity overflow or an error. Here’s how to remove it:

Possible causes:

The result exceeds 12 digits
The memory exceeds 12 digits
Division by zero

To clear the error:

Press the decimal point key, then press 9/CE to clear the error.

The contents of the memory will be retained - you just need to clear the error state and continue your calculations.

Question 4

How to perform a simple subtraction with the SHARP EL-2901RH?

Accepted Answer

To perform a simple subtraction on your SHARP EL-2901RH calculator, follow these steps:

Make sure the calculator is turned on by setting the switch at the bottom left to P (print mode)
Press CE (Clear Entry) to reset the display and clear the last operation
Enter the first number (the number you want to subtract from)
Press the - (minus) key, located to the right of the numeric keys
Enter the number to subtract (the second number)
Press = to get the result, which will be displayed and printed automatically

Concrete example: To calculate 50 - 12, do: 50 → (press -) → 12 → (press =) → Result: 38

Addition mode (decimal switch in position A): If you set the decimal switch to A, the decimal point is automatically placed on the 2nd digit from the right. This allows for subtractions of amounts without having to enter the decimal point manually, which is very useful for money operations (example: 50.00 - 12.00 to calculate directly without entering the point).

Tip in case of error: If you make a mistake entering a digit before pressing the subtraction key, press CE to cancel the entry and start the operation again. If the error occurs after the first number, you can also press C to completely clear and start from zero.

Printing the result: When the switch is in P mode (printing), each operation is automatically printed on the 57-58 mm wide paper roll. The result of your subtraction will be printed with the asterisk symbol to indicate the final total. The mechanical printer displays about 2.1 lines per second.

Question 5

How to change the paper roll on the SHARP EL-1750PIII calculator?

Accepted Answer

The SHARP EL-1750PIII calculator uses a standard thermal paper roll. Here’s how to replace it:

Prepare the new roll. Unroll the end of the paper roll by a few centimeters.
Insert the roll. Engage the end of the paper roll into the designated opening under the calculator.
Advance the paper. Turn on the device and press the paper advance button to properly position the roll.
Lift the metal holder. Raise the metal holder of the roll and adjust the roll until it is securely in place.

Important: Never pull the paper backward, as this could damage the printing mechanism. Always prefer advancing forward using the dedicated button.

If the printing becomes faint after changing, gently clean the printing wheel with a soft brush.

Question 6

How to add multiple products with the SHARP EL-2607PG calculator?

Accepted Answer

To add multiple products with the SHARP EL-2607PG calculator, you can follow these simple steps:

Steps to add multiple products:

Turn on the calculator by pressing the ON button.
Calculate each product by multiplying the quantities by the unit prices:

Enter the quantity of the first product.
Press the × (multiplication) button.
Enter the unit price of the first product.
Press the = button to get the result.

Note or memorize this result (depending on the calculator's features, you can use the M+ key to add it to memory).
Repeat steps 2 and 3 for each product to be added.
Add the results using the M+ key to accumulate the products, or add them manually:

After calculating a product, press M+ to add it to memory.
After adding all products, press MR (memory recall) to display the total sum.

If your calculator does not have memory functions, you will need to note each product and then add them manually using the + key.

This method allows you to calculate and add multiple products quickly and efficiently with your SHARP EL-2607PG.

Question 7

How to insert the print ribbon into the SHARP EL-2607PG calculator?

Accepted Answer

To insert the print ribbon into your SHARP EL-2607PG calculator, follow these simple steps:

Steps to insert the print ribbon

Turn off the calculator to avoid any damage or errors during installation.
Open the ribbon compartment, usually located on the top or side of the calculator. Carefully lift or remove the cover.
Prepare the ribbon by ensuring that the ink part is facing down, ready to be printed.
Insert the ribbon into the feed rollers following the path provided inside the compartment. Make sure the ribbon is taut and correctly positioned to avoid jams.
Close the cover of the ribbon compartment, ensuring it is securely latched.
Turn the calculator back on and perform a print test to check that the ribbon is working correctly.

If the ribbon does not print correctly, check that it is taut and positioned properly, and replace it if necessary.

Question 8

Why is the printing on the paper roll of my SHARP EL-1611E calculator too faint?

Accepted Answer

If the printing on the paper roll of your SHARP EL-1611E calculator is too faint, several causes may be responsible:

1. Quality and type of paper

Use a compatible and good quality thermal paper roll. Inappropriate or poor quality paper can lead to faint or incomplete printing.

2. Condition of the print head

The print head may be dirty or worn out. Gently clean the print head with a soft, dry cloth to remove any dust or residue that may affect print quality.

3. Power supply

If your calculator runs on batteries, check that they are sufficiently charged. A low power supply can affect the power of the print head and thus the quality of the output.

4. Print settings

Check the calculator settings to see if it is possible to adjust the intensity or density of the printing. Some models allow you to modify these settings to improve visibility.

By following these tips, you should be able to improve the print quality of your SHARP EL-1611E calculator.

User manual SHARP Calculator : user manuals and guides in PDF

Models SHARP Calculator most viewed

Other categories SHARP

Recent questions about Calculator SHARP