CDM1074 - Drill/Driver Ferm - Free user manual and instructions

Product type	Cordless drill/driver
Brand	Ferm
Model	CDM1074
Rated voltage	7.2 V
Battery type	Lithium-Ion
Charger voltage	230 V~ / 50 Hz
Charging time	3 to 5 hours
No-load speed	0 - 500 rpm
Weight	0.93 kg
Sound pressure level (Lpa)	68.5 + 3 dB(A)
Sound power level (Lwa)	79.5 + 3 dB(A)
Vibration level	1.92 + 1.5 m/s²
Number of torque settings	17 (15 positions + drilling)
Work light	LED (dedicated switch)
Bit holder	Magnetic, with locking sleeve
Package contents	Screwdriver, table stand, charger, magnetic bit holder, 16 bits, manual, warranty card
Usage	Screwing and drilling
Electrical safety	Double insulation (class II)
Maintenance	Clean with a damp soft cloth; no lubrication required
Warranty	See attached warranty card

Frequently Asked Questions - CDM1074 Ferm

How to charge the battery?

Plug the adapter into the table stand (6) or directly into the tool’s base. Charging starts when the adapter is plugged into the mains. The charging time is 3 to 5 hours. The LEDs indicate the charging status (flashing red = charging, all on = charged).

How to adjust the torque setting?

Turn the torque adjustment ring (3) to the desired position, from 1 (low) to 15 (high) or to the drilling symbol. Choose the lowest possible setting for screwing, then increase if the motor stalls.

How to change the bits?

Pull the locking sleeve (2) backward, insert the bit or magnetic bit holder, then release the sleeve to lock. To remove, pull the sleeve again and remove the bit.

How to turn on the LED light?

Press the LED work light switch (11) to turn on, and a second time to turn off. The light is independent of the motor.

What to do if the battery does not charge?

Check that the ambient temperature is between 5°C and 40°C. Ensure the charger is properly plugged in. If the red LED flashes every 2 seconds and the other LEDs are on, a fault has occurred; unplug the charger and contact your supplier.

How to reverse the rotation direction?

Use the direction switch (9): push it left for screwing (clockwise), right for unscrewing (counterclockwise). To lock the tool in stop, set it to the center position.

What is the maximum speed?

The maximum no-load speed is 500 rpm. It is adjustable by pressing more or less on the on/off switch (8).

How long does it take to charge the battery?

The charging time is approximately 3 to 5 hours. The Lithium-Ion battery can be charged at any time without loss of capacity.

Can I use drill bits?

Yes, the tool accepts drill bits with a hexagonal shank. Use the magnetic bit holder for short bits or insert 50 mm bits directly into the sleeve.

How to clean the device?

Clean the housing with a soft cloth, preferably after each use. For stubborn dirt, use a cloth dampened with soapy water. Do not use solvents. The ventilation slots must be kept free of dust.

USER MANUAL CDM1074 Ferm

CORDLESS SCREWDRIVER CDM1074

Thank you for buying this Ferm product.

By doing so you now have an excellent product, delivered by one of Europe's leading suppliers.

All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.

The numbers in the text refer to the diagrams on pages 2 - 3.

Read the operating instructions carefully before using this device. Familiarise yourself with its functions and basic operation. Service the device as per the instructions to ensure that it always functions properly. The operating instructions and the accompanying documentation must be kept in the vicinity of the device.

Contents

1. Machine information
2. Safety instructions
3. Mounting accessories
4. Operation
5. Service & maintenance

1. MACHINE INFORMATION

Technical specifications

Voltage 7,2 V

Lithium-Ion

Charger voltage 230 V

Charger frequency 50 Hz

Charging time 3 - 5 hours

Chuck 1/4" hexagonal

Drill speeds 1

Max. torque 10 Nm

No load speed 0 - 500/min

Weight 0.93 kg

Lpa (acoustic pressure) 68.5 + 3 dB(A)

Lwa (acoustic power) 79.5 + 3 dB(A)

Vibration 1.92 + 1.5 m/s

2

Vibration level

The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned

• using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
• the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns

Contents of packing

1 Cordless screwdriver
1 Desktop holder with bit storage
1 Charger
1 Magnetic bit holder
16 Bits
1 Operating instructions
1 Safety instructions
1 Warranty card

Check the appliance, any loose parts and accessories for damage caused during transport

Product information

Fig. 1 + 2

1. Bit holder
2. Locking sleeve
3. Torque setting ring
4. Magnet
5. Desktop holder
6. Charger connection
7. Worklight
8. On/Off switch
9. Direction switch
10. Battery status switch
11. LED work light switch
12. Battery status indication

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Indicates electrical shock hazard.

The number of revolutions of the machine can be electronically set.

Do not use in rain.

Indoor use only

In case of failure, the transformer is not dangerous

Do not dispose of in household waste.

Specific safety instructions

• This appliance is not intended for use by persons (including children) with reduced sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Important safety notes on charger and internal battery

If you come in contact with acid from the battery, rinse it off with water immediately. If acid gets into your eyes, rinse out your eyes at once with water and contact a doctor immediately!

1. Read and note the operating instructions and safety notes for the charger and internal battery before use!
2. NB! Only use the charger that was supplied by the manufacturer - otherwise you will risk an accident.
3. Protect the charger and power tool from moisture, e.g. rain or snow.
4. Always check that all cables are connected correctly before using the charger.
5. If you discover that a cable is damaged, you should not use the charger again. Have the damaged cable replaced immediately.
6. When the charger is not in use, the mains plug should be removed from the power socket. Do not pull out the plug by grasping the cable.
7. If the charger has been dropped or has otherwise been exposed to high mechanical stresses, you should have it checked for damage by an authorized dealer before using it again. Damaged parts should be repaired.
8. Exercise caution when handling the tool and do not drop it or expose it to impacts.
9. Never attempt to repair the charger or internal battery yourself. Repairs must always be carried out by an authorized dealer - otherwise you risk an accident.
10. Before cleaning or servicing the charger, always pull the plug from the charger socket.
11. Never charge the tool when the ambient temperature is below 5^ C or above 40^ C.
12. Never throw the tool onto a fire or into water. This will risk explosion!

Electrical safety

Always check that the voltage on the battery pack corresponds to the voltage on the rating plate. Also check that your mains voltage corresponds to the input voltage of the battery charger.

Class II machine - Double insulation - You don't need any earthed plug.

Replacing cables or plugs

Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.

- The tool is suitable for use as a screwdriver and drill. Any other application is specifically excluded.

3. MOUNTING ACCESSORIES

Inserting and removing bits

Fig. 1

In addition to screwdriver bits with a hexagonal shaft, this tool can also accommodate drill bits with a hexagonal shaft.

Always use short screwdriver bits in combination with the magnetic bit holder. The 50 mm screwdriver bits can be used without the magnetic bit holder.

• Pull back the locking sleeve (2) and insert the magnetic bit holder or 50mm screwdriver bit.
• Release the locking sleeve.
• To remove, pull back the locking sleeve and remove the bit or magnetic bit holder.

4. OPERATION

Always follow the safety notes and the relevant safety code.

Hold the appliance firmly and press the screwdriver steadily onto the work piece. Do not overload the appliance. Only use bits with no visible wear. Worn bits will have a bad effect on the functioning of the appliance.

Adjusting the torque

Fig. 1

The appliance has 17 different torque settings with which to set the power for driving and removing screws.

- Set the torque settings ring (3) to the desired position. The available torque settings are indicated on the settings ring by the numbers 1 to 15 and by dots between the figures to define intermediate settings. And a setting for drilling indicated by the drill icon (17 in total).

- You should preferably choose a setting as low as possible when using the screwdriver. Select a higher setting if the motor slips.

Driving and removing screws

Fig. 1

• Set the direction switch (9) to position ‘→’ in order to drive screws.
• Set the direction switch (9) to position ‘←’ in order to remove screws.

Ensure that the direction switch (9) is always set to ‘→’ during drilling and the drill symbol selected on the torque settings ring.

Switching the device on and off

Fig. 1

• Depress the on/off switch (8). It regulates the speed of the appliance by transmitting power to the switch.
• Release the on/off switch (8) to halt the drill chuck immediately, it will no longer run on.
• Move the direction reversing switch (9) to the centre in order to lock the appliance in its disabled state.

The tool will turn at its slowest speed when the switch is depressed lightly. The tool will turn at its fastest speed when the trigger is fully depressed.

Only lay down the appliance when it has stopped running completely. Do not place it on a dusty surface as particles of dust could get into the mechanism.

LED work light

Fig. 2

• Press the LED work light switch (11) once to switch the LED work light on.
• Press the LED work light switch (11) again to switch the LED work light off.

Charging the battery

• Only use the battery charger in a temperature range between +5 °C to +40 °C.
• Only use the battery charger in dry, ventilated rooms.

One advantage of using Lithium-Ion batteries is that, until the battery is almost empty, hardly any power fading is noticeable. The machine can be used until you start noticing that the power of the

drill is elapsed. The battery is discharged now and needs to be charged.

In comparison to NiCd and NiMH cells, Lithium-Ion cells have no memory effect due to intermedial charging. While NiCd and NiMH batteries need to be discharged before charging, a Lithium-Ion block does not need to be completely discharged. This battery block can be charged at any time despite its current power level without losing much of its original power and endurance.

The charger is equipped with a special plug. This Lithium Ion battery pack is only to be charged with this dedicated charger. The intergrated electronics in this dedicated charger are custom made for this Lithium-Ion battery pack. Using other chargers/adapters will cause irreversible damage to the battery.

The internal battery can be charged in 2 different ways:

• Plug the adapter into the desktop holder (6). Charging will start when the adapter is plugged to the mains supply and the tool placed in the desktop holder (Fig. 3).
• Plug the adapter directly into the bottom of the foot of the tool. Charging will start when the adapter is plugged to the mains supply.

3 LED charging & battery status indication Fig. 2

When the charger is connected, these 3 LEDs indicate the charging status.

• When the battery is empty and charging begins, the red LED will blink, with the yellow and green LED off.
• When the battery is less than halfway charged, the red LED will be on and the yellow LED will be blinking.
• When the battery is more than halfway charged, both the red and yellow LED will be on and the green LED will be blinking.
• When all LEDs are lit up, charging is completed and the battery is full.
  • After 10 seconds all LEDs will switch off and charging will stop.

When the charger is not connected, these 3 LEDs indicate the battery status when the battery status switch (10) is pressed.

• When the red LED lights up, the battery is empty and needs to be charged.
• When the red and yellow LED lights up, the battery is half full.
• When all LEDs light up, the battery is completely full.

When the red LED continues to blink with an interval of 2 seconds and no other LED is lit up, a battery failure occurred and charging has stopped. Disconnect the charger and contact your supplier.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live when carrying out maintenance work on the motor.

These machines have been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning.

Cleaning

Keep the ventilation slots of the machine clean to prevent overheating of the engine. Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the ventilation slots free from dust and dirt. If the dirt does not come off use a soft cloth moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. Separate you find an exploded view showing the parts that can be ordered.

Environment

To prevent damage during transport, the appliance is delivered in a solid packaging which consists largely of reusable material. Therefore please make use of options for recycling the packaging.

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Warranty

The warranty conditions can be found on the separately enclosed warranty card.

The product and the user manual are subject to change. Specifications can be changed without further notice.

AKKU-BOHRSCHRAUBER CDM1074

1. MACHINE INFORMATIE

Technische specificaties

Voltage 7,2 V

Lithium-Ion

Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.

TOURNEVIS SANS FIL CDM1074

Mandrin 1/4" hexagonal

Vitesse 1

Couple max 10 Nm

CHAVE DE FENDAS CDM1074

Bucha 1/4" hexagonal

Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.

Chuck 1/4" hexagonal

Borrhastigheter 1

Max. vridmoment 10 Nm

LEDNINGSFRI SKRUETRÆKKER CDM1074

BEVIELIS ATSUKTUVAS CDM1074

AKUKRUVIKEERAJA CDM1074

Täname, et ostsite selle Fermi toote.

SURUBELNITĂ FĂRĂ FIR CDM1074

DECLARATION OF CONFORMITY

(GB) We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijk heid dat dit product voldoet aan, en in overeenstem ming is met, de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants:
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento:
(PT) Declaramos por nossa total responsabilida-de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem:
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti:
(SV) Vi garanterar på eget ansvar att denna produkt upp fyller och följer följande standarder och bestämmelser:
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset:
(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende standarder og regler:
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser:
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak:
(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami:

(SK) Vyhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcimi normami a predpismi:
(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom:
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach:
(LT) Prisiimdami visą atsakomybę deklaruojame, kad šis gaminys atitinka žemiau paminėtus standartus arba nuostatus:
(LV) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem:
(ET) Deklareerime meie ainuvastutusel, et see toode on vastavuses ja kooskõlas järgmiste standardite ja määrustega:
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive:
(HR) Izjavljujemo pod vlastitom odgovornoLšu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama:
(SR) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama:
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам:
(UK) На свою власну відповідальність заявляемо, що дане обладнання відповідає наступним стандартам і нормативам:
(EL) Δηλώνουμε υπεύθυνα ότι προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμο ύς και πρότυπα:
(BG) Ние заявяваме, по своя собствена отговорност, че този продукт отговаря на следните стандарти и директиви

EN50366, EN55014-1, EN55014-2, EN60745-1, EN60745-2-2, EN60335-1, EN60335-2-29, EN61000-3-2, EN61000-3-3

2006/42/EC, 2006/95/EC, 2004/108/EC, 2002/96/EC, 2002/95/EC

Zwolle, 01-01-2010

J.A. Bakker-van logen

CEO Ferm BV

It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.

Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle The Netherlands

Spare parts list

No.	Description	Position
409565	Gearbox + chuck	1 til 10 + 14 til 29
409566	Motor complete	30 + 31
409567	Switch complete	34 til 36
409569	Battery complete	38 + 40
409568	LED holder + buttons	39 + 41 + 42
409563	Housing assy	11 + 12 + 32 + 33 + 43
409562	Doublesided bits set	13 + 44

Exploded view