PANASONIC ERGN300 - Electric mower

ERGN300 - Electric mower PANASONIC - Free user manual and instructions

Find the device manual for free ERGN300 PANASONIC in PDF.

📄 276 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice PANASONIC ERGN300 - page 4
Pick your language and provide your email: we'll send you a specifically translated version.
Product Type Electric hair trimmer for nose, ears, eyebrows, mustache and beard
Brand Panasonic
Model ERGN300
Power Supply 2 AAA LR03 alkaline batteries (not included)
Battery Life Approximately 6 months (1 use/week, 90 seconds)
Main Functions Trims nose, ear, eyebrow, mustache, beard hair
Blade Material Stainless steel (inner metal blade)
Included Accessories Cleaning brush
Cleaning Washable with water (mild soap) or dry brushing
Maintenance Blade replacement and regular cleaning
Spare Parts Replaceable outer and inner blades
Safety Protective cap, do not insert too deeply, use under supervision for children
Recommended Use Dry use on clean skin, washable after use
Minimum Age 8 years with supervision
Noise Level 58 dB (A) re 1 pW
Household Use Yes
General Information Washable product (waterproof symbol), do not use hot water or detergents other than soap

Frequently Asked Questions - ERGN300 PANASONIC

How to install the batteries in the ERGN300 trimmer?
Pull the battery cover to remove it. Insert two AAA LR03 alkaline batteries observing polarity, then close the cover. Make sure the device is off before installation.
What is the battery life?
With two AAA Panasonic LR03 alkaline batteries, the battery life is approximately 6 months with weekly use of about 90 seconds in dry mode at room temperature (20°C).
How to clean the trimmer?
You can clean the trimmer in two ways: 1) Dry cleaning: remove the blades and brush with the provided brush. 2) Water cleaning: open the water inlet, foam with mild soap, rinse with clean water and dry. Do not use hot water or harsh detergents.
Can I use the trimmer underwater or in the shower?
The device is washable with water but not designed for underwater use. It can be cleaned under a faucet but should not be submerged. Use it dry only.
How to replace the blade?
Make sure the device is off. First remove the wash switch ring if necessary. Turn the outer blade to remove it, then pull out the inner blade. Insert the new inner blade, then attach the outer blade by aligning the marks.
Is the device suitable for children?
The device can be used by children aged 8 years and older under supervision. Children must not play with it and cleaning must not be done by children without supervision.
What to do if the trimmer stops working?
First check the correct battery installation (polarity and condition). If the problem persists, clean the inner blade and the trimmer housing. If nothing changes, replace the batteries or the blade. Contact an authorized service center if necessary.
Can the cutting length be adjusted?
This device does not allow adjusting the cutting length. It is designed to cut very short hair (less than 0.5 mm) and is not suitable for long or uniform cutting.
Can I use batteries other than LR03?
It is recommended to use alkaline AAA LR03 batteries (type R03). Using different batteries may reduce performance or damage the device. Do not recharge non-rechargeable batteries.
Where to find replacement blades?
Replacement blades (inner and outer) are available from authorized Panasonic service centers or authorized dealers. Refer to the manual for exact references or contact customer service.

User questions about ERGN300 PANASONIC

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Electric mower in PDF format for free! Find your manual ERGN300 - PANASONIC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ERGN300 by PANASONIC.

USER MANUAL ERGN300 PANASONIC

Operating Instructions (Household) Nose & Facial Hair Trimmer Model No. ER-GN300

PANASONIC ERGN300 - 1

English. 3
Deutsch 19
Francais. 35
Italiano 51
Nederlands 67
Espanol. 83
Dansk 99
Portugues. 115
Norsk 131
Svenska 147
Suomi 163
Polski 179
Česky 195
Slovensky 211
Magyar 227
Româna 245
Türkce 261

Panasonic

Operating Instructions (Household) Nose & Facial Hair Trimmer Model No. ER-GN300

Contents

Safety precautions 5

Parts identification 8

Installing or replacing the alkaline batteries..... 9

Before use 9

Using 10

Cleaning 11

Opening and closing the water inlet. 13

Installing or removing the blade 13

Installing or removing the trimmings box.....15

Troubleshooting 16

Specifications 17

Thank you for purchasing this Panasonic product. Before operating this unit, please read these instructions completely and save them for future use.

Warning

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
  • Cleaning and user maintenance shall not be made by children without supervision.

  • The following symbol means that this appliance can be cleaned under the water.

PANASONIC ERGN300 - Warning - 1

Safety precautions

To reduce the risk of injury, loss of life, electric shock, fire, and damage to property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

PANASONIC ERGN300 - Explanation of symbols - 1

WARNING

Denotes a potential hazard that could result in serious injury or death.

PANASONIC ERGN300 - WARNING - 1

CAUTION

Denotes a hazard that could result in minor injury or property damage.

The following symbols are used to classify and describe the type of instructions to be observed.

PANASONIC ERGN300 - CAUTION - 1

This symbol is used to alert users to a specific operating procedure that must not be performed.

PANASONIC ERGN300 - CAUTION - 2

This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.

PANASONIC ERGN300 - CAUTION - 3

WARNING

This product

Do not store within reach of children or infants. Do not let them use it.

PANASONIC ERGN300 - This product - 1

  • Putting parts or accessories in the mouth may cause an accident or injury.
  • Store with the protection cap attached after use.

PANASONIC ERGN300 - This product - 2

Immediately stop using if there is an abnormality or malfunction.
- Using it in such conditions may cause fire, or injury.

PANASONIC ERGN300 - This product - 3

CAUTION

To protect your skin

Do not press the blade with excessive force or insert too deeply into your nostril/ear canal.
Do not press the blade with excessive force against your skin.

  • Doing so may result in injury to your skin.

PANASONIC ERGN300 - To protect your skin - 1

Do not touch the blade of the inner blade (metallic part) with your finger.
- Doing so may result in injury to your finger.

PANASONIC ERGN300 - To protect your skin - 2

Check the blade for deformation or damage before use. Use the trimmer to cut nose hair and ear hair and outline eyebrows, moustache, or beard.

  • Failure to do so may result in injury to your skin.

PANASONIC ERGN300 - To protect your skin - 3

CAUTION

This product

PANASONIC ERGN300 - This product - 1

Do not share with your family or others.

  • Doing so may result in infection or inflammation.

PANASONIC ERGN300 - This product - 2

Do not drop or subject to shock.

  • Doing so may cause injury.

PANASONIC ERGN300 - This product - 3

Never modify, disassemble, or repair.

  • Doing so may cause an accident or injury.

Contact an authorized service centre for repair.

The batteries

PANASONIC ERGN300 - The batteries - 1

Do not throw into fire, short circuit or disassembly.

  • Doing so may cause a burn or injury.

PANASONIC ERGN300 - The batteries - 2

Always follow the precautions printed on the alkaline batteries.

Check the polarity of the alkaline batteries (and) and install them correctly.

Do not mix new and old alkaline batteries or different types of alkaline batteries.

Remove the alkaline batteries immediately and dispose of them safely when they are discharged.

Remove the alkaline batteries when not using the appliance for an extended period of time.

Please use the alkaline batteries by the recommended use-by date.

Non-rechargeable batteries are not to be recharged.

  • Failure to do so may cause injury or surrounding contamination due to heat generation, bursting, or leakage of the alkaline batteries.

Parts identification

PANASONIC ERGN300 - Parts identification - 1
A

PANASONIC ERGN300 - Parts identification - 2

PANASONIC ERGN300 - Parts identification - 3

A Protective cap

⑧ Filter
⑨ Wash switch ring
Water inlet

Main body

① Outerblade
② Inner blade
③ Trimmings box
④ Water outlet
⑤ Exhaust hole
⑥ Battery cover
⑦ Power switch [O/I]

Accessory

Cleaning brush (Brush)

Alkaline batteries are not enclosed.

Installing or replacing the alkaline batteries

  • Make sure that the power is off.

  • Pull the battery cover straight to remove it.

  • Check the polarity of the alkaline batteries ( and and install them.
  • Insert the battery cover straight.

You can use the appliance for approximately 6 months with two Panasonic LR03 (AAA Alkaline Batteries). (When using dry in an environment at a 20^ room temperature, once a week, and 90 seconds at a time.)

PANASONIC ERGN300 - Installing or replacing the alkaline batteries - 1

Notes

  • When insert the alkaline batteries, wipe off the main body carefully to prevent water droplets from getting inside.
  • Confirm nothing adheres to the terminals (⊕ and ⊙ of the alkaline batteries.
  • Be sure to use LR03 (AAA Alkaline Batteries). If any batteries other than the specified ones are used, the power and the number of times of use will be different.
  • Panasonic alkaline batteries are recommended.
  • When replacing alkaline batteries, replace both of them with new ones.

Before use

Be sure to close the water inlet of the wash switch ring during use. Otherwise, the main body cannot provide sufficient suction power.

Check that the marks of "1", "O" and "▲" align (as shown in right figure).

PANASONIC ERGN300 - Before use - 1

Using

  1. Remove the protective cap and hold the main body so as not to block the exhaust hole (4).
  2. Slide the power switch on the main body to the "O" position to turn on the power. The outer blade surface may get a little warm during use, but performance will not be affected.

PANASONIC ERGN300 - Using - 1

3.Trim

Trimming your nose hair and ear hair

  1. Insert the tip (b) of the outer blade into your nostril or ear canal.
  2. Insert it slowly so as not to injure your nostril or ear canal.
  3. Cut the nose hair and ear hair by moving the main body.
  4. Cut hairs using the tip (b) of the outer blade (metallic part).
  5. Some trimmings may remain inside your nostril or ear canal after cutting, so remove them using a tissue or similar.

PANASONIC ERGN300 - Trimming your nose hair and ear hair - 1

PANASONIC ERGN300 - Trimming your nose hair and ear hair - 2

PANASONIC ERGN300 - Trimming your nose hair and ear hair - 3

Outlining your eyebrows, moustache, or beard

  1. Apply the tip of the outer blade to the hair (eyebrow, moustache or beard) you would like to cut.
  2. Cut the hair by moving the appliance slowly against the direction of hair growth.

  3. You cannot trim the hair to length with this appliance.

  4. It is not suitable for the hair below 0.5 mm .

PANASONIC ERGN300 - Trimming your nose hair and ear hair - 4

PANASONIC ERGN300 - Trimming your nose hair and ear hair - 5

  1. After use, slide the power switch on the main body to the "I" position to turn off the power and clean it. (See page 11).

10

Cleaning

Wet cleaning

  1. Wet the outer blade with water, and apply some hand soap and some water to the outer foil.
  2. Slide the power switch to the "O" position, and let it foam for approximately 10 seconds.
  3. Turn off the power.

PANASONIC ERGN300 - Wet cleaning - 1

To clean lightly dirty parts To clean heavily dirty parts

  • Quick cleaning
  • Open the water inlet (see page 13) and turn on the power again.

  • If the trimmings box is removed, open the water inlet after attaching the trimmings box (see page 15).

PANASONIC ERGN300 - To clean lightly dirty parts To clean heavily dirty parts - 1

  1. Pour water through the water inlet at the “ ” above the “ ” mark, rinse well and slide the power switch to the “I” position.

PANASONIC ERGN300 - To clean lightly dirty parts To clean heavily dirty parts - 2

  • Complete cleaning
  • Slide the power switch to the "I" position.
  • Remove the blades and the trimmings box (see pages 13 and 15) and rinse under running water.

  • Cover the drainage outlet of washbasin to prevent the inner blade from flowing away.

PANASONIC ERGN300 - To clean lightly dirty parts To clean heavily dirty parts - 3

PANASONIC ERGN300 - To clean lightly dirty parts To clean heavily dirty parts - 4

PANASONIC ERGN300 - To clean lightly dirty parts To clean heavily dirty parts - 5

PANASONIC ERGN300 - To clean lightly dirty parts To clean heavily dirty parts - 6

  1. Wipe off water with a towel or similar item, and let it dry naturally.

  2. It will dry faster with the blades and the trimmings box removed (see pages 13 and 15).

PANASONIC ERGN300 - To clean lightly dirty parts To clean heavily dirty parts - 7

Cleaning with the brush

Remove the blades and the trimmings box (see pages 13 and 15) and lightly brush off the trimmings with the brush.

  • Be careful not deform the inner blade
  • Be careful not to damage the filter.

PANASONIC ERGN300 - Cleaning with the brush - 1

Notes

  • The battery cover should not be removed from the main body as this can affect the watertight construction of the appliance.
  • Do not use hot water or any detergents other than hand soap. Doing so may result in malfunction.
  • In order to prevent malfunction, be careful not to hit the appliance against a washbasin.
  • Do not use thinner, benzine, alcohol or other chemicals to clean the appliance. Doing so may result in malfunction, cracking or discoloring of the parts. Please use a cloth soaked with soapy water to wipe the dirt.
    After cleaning, be sure to attach the blades, the trimmings box and the protective cap. (See pages 14~15)

Opening and closing the water inlet

1 How to open

Rotate the wash switch ring until its "O" mark aligns with "i" mark of the main body to open the water inlet.

2 How to close

Rotate the wash switch ring until its "O" mark aligns with "A" mark of the main body.

PANASONIC ERGN300 - How to close - 1

PANASONIC ERGN300 - How to close - 2

Installing or removing the blade

  • Make sure that the power is off.

How to remove the blade

  1. Rotate the outer blade and remove it.

  2. Rotate the outer blade until its " " mark aligns with the " " mark of the main body.

PANASONIC ERGN300 - How to remove the blade - 1

  1. Pull to remove the inner blade.

PANASONIC ERGN300 - How to remove the blade - 2

How to attach the blade

  1. Insert the inner blade straight along the inner surface of the outer blade.

PANASONIC ERGN300 - How to attach the blade - 1

  1. Insert the main body's shaft (c) into the hole of the inner blade.

  2. Align the "1" mark of the outer blade with the "1" mark of the trimmer.

PANASONIC ERGN300 - How to attach the blade - 2

  1. Rotate to attach the outer blade.

  2. Rotate the outer blade to align its "1" mark with the "▲" mark of the main body.

PANASONIC ERGN300 - How to attach the blade - 3

Installing or removing the trimmings box

  • Make sure that the power is off.

How to remove

Rotate to remove the wash switch ring.

  • Rotate the wash switch ring until its "O" mark aligns with "O" mark of the main body.

PANASONIC ERGN300 - How to remove - 1

PANASONIC ERGN300 - How to remove - 2

How to attach

  1. Insert the trimmings box.

  2. Align the "○" mark of the wash switch ring with the "●" mark of the main body.

  3. Be careful not to damage the filter with the shaft (4)

  4. Rotate to attach the wash switch ring.

  5. Rotate the wash switch ring to align its "O" mark and the "▲" mark of the main body.

PANASONIC ERGN300 - How to attach - 1

PANASONIC ERGN300 - How to attach - 2

Troubleshooting

Problem Action

The cutting performance has reduced.

Replace the blade.

(See pages 13~14)

There is an odd odour.

Replace the alkaline batteries.

Blade does not move/ rotate smoothly.

(See page 9)

The suction power is low.

Clean the inner blade.

(See pages 11~12)

The appliance is not turned on.

Clean the trimmings box.

(See pages 11~12).

Close the water inlet.

(See pages 9 and 13).

Place the alkaline batteries correctly.

(See page 9).

Replace the alkaline batteries.

(See page 9).

If the problems still cannot be solved, contact the store where you purchased the appliance or a service centre authorized by Panasonic for repair.

Specifications

Power supply Dry-cell battery
Battery typeTwo LR03 (AAA Alkaline Batteries) (Sold separately)
Airborne Acoustical Noise 58dB (A) re 1 pW)

This product is intended for household use only.

Disposal of Old Equipment

Only for European Union and countries with recycling systems

PANASONIC ERGN300 - Only for European Union and countries with recycling systems - 1

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.

For more information about collection and recycling, please contact your local municipality.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Panasonic

Betriebsanleitung

Identification of dele 104

33, Wanbao North Street, Wanbao Industry Zone, Zhongcun, Panyu District, Guangzhou City, Guangdong Province, China

YETKILI TEMSILCI

Ithalatci Firma:

Tesan Iletisim A.S.

Cobançesme Mah. Bilge Sok. No:17

34196 Yenibosna- Istanbul

Tel: 0212 454 60 70 Faks: 0212 454 60 20

www.tesan.com.tr

URUNUN KULLANIM ÖMRÜ 7 YILDIR

© Panasonic Corporation 2018

EN,GE,FR,IT,DU,SP,DA,PT,NW, SW,FI,PL,CZ,SK,HU,RO,TK

Printed in China

ER970GN3001503 S0718-0

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : PANASONIC

Model : ERGN300

Category : Electric mower