Q: How do I put the cradle cover back on after washing it?

The BabyGO Amila cradle has a fully removable and washable fabric cover . Although the manual does not provide detailed step-by-step instructions for putting it back on, here is what you need to know: After washing Ensure that the cover is completely dry before putting it back on (do not use a dryer) Make sure that the fabric and seams remain intact after washing Inspect the attachment points (usually Velcro, buttons, or cords depending on your model) Replacing the cover The cover can be removed and replaced by reversing the removal process. Align it with the cradle structure and securely attach it on all sides. Ensure that the cover is taut and correctly positioned before using the cradle. For precise and detailed instructions specific to your model, contact BabyGO customer service at info@babygo.eu — they can send you photos or videos of the installation process.

Q: How to close and lock the BabyGO Levels high chair?

The BabyGO Levels high chair closes via several locking systems: Closing the safety belt The 5-point restraint system locks as follows: Insert both ends of the belt into the buckles until you hear a click - this click indicates that the buckles are properly locked Adjust the length of the belt using the adjustable buckle to fit the harness to your child's size To open the harness, simply press the buckles to release them Locking the removable tray The tray also attaches with a click system: once you hear the “click” , the tray is properly installed and locked. To remove it, press the two buttons located on each side of the tray, then lift it upwards. Folding the chair If you want to fold the chair for storage, press both buttons located at the bottom of the seat simultaneously, then fold the rear leg tube forward.

Q: How to rotate the BabyGO Nova+ 360 car seat?

The BabyGO Nova+ 360 car seat features a 360° rotation function to facilitate the installation and removal of the child. Rotation steps: Press the rotation button (K) located on the seat Gently turn the seat towards the door to install or remove the child After finishing, turn the seat in both directions until it locks in the driving position Important before each trip: Before starting the vehicle, ensure that the seat is correctly locked in the driving position . Never drive with an unsecured or incompletely locked seat. If one side does not lock, try the locking maneuver again. This rotation works with the support leg deployed and the seat can accommodate children from 40 to 105 cm.

Question 1

How do I put the cradle cover back on after washing it?

Accepted Answer

The BabyGO Amila cradle has a fully removable and washable fabric cover. Although the manual does not provide detailed step-by-step instructions for putting it back on, here is what you need to know:

After washing

Ensure that the cover is completely dry before putting it back on (do not use a dryer)
Make sure that the fabric and seams remain intact after washing
Inspect the attachment points (usually Velcro, buttons, or cords depending on your model)

Replacing the cover

The cover can be removed and replaced by reversing the removal process. Align it with the cradle structure and securely attach it on all sides. Ensure that the cover is taut and correctly positioned before using the cradle.

For precise and detailed instructions specific to your model, contact BabyGO customer service at info@babygo.eu — they can send you photos or videos of the installation process.

Question 2

How to close and lock the BabyGO Levels high chair?

Accepted Answer

The BabyGO Levels high chair closes via several locking systems:

Closing the safety belt

The 5-point restraint system locks as follows:

Insert both ends of the belt into the buckles until you hear a click - this click indicates that the buckles are properly locked
Adjust the length of the belt using the adjustable buckle to fit the harness to your child's size
To open the harness, simply press the buckles to release them

Locking the removable tray

The tray also attaches with a click system: once you hear the “click”, the tray is properly installed and locked. To remove it, press the two buttons located on each side of the tray, then lift it upwards.

Folding the chair

If you want to fold the chair for storage, press both buttons located at the bottom of the seat simultaneously, then fold the rear leg tube forward.

Question 3

My 15-month-old child doesn't hold their head well in the Lumo2 and falls forward when they fall asleep. How can I keep them properly secured?

Accepted Answer

At 15 months, your child should use the integrated 5-point harness of the Lumo2. If they fall forward when they fall asleep, here are some points to check:

Properly position the harness straps: They should pass at shoulder level of your child, neither too high nor too low. Incorrect strap positioning is the main cause of a head that tilts forward.
Tighten the harness securely: After inserting the clips into the buckle, pull on the adjustment strap to ensure the harness fits snugly against your child's body. A harness that is too loose does not hold them adequately.
Adjust the headrest (component A): The adjustable headrest should be aligned with the height of your child's shoulders. Use the height adjustment mechanism to properly position the headrest that supports their head, especially when they are sleeping.

Also, check that the backrest of your car seat is not too reclined, as this would push your child down into the Lumo2 and worsen the issue.

Question 4

How to rotate the BabyGO Nova+ 360 car seat?

Accepted Answer

The BabyGO Nova+ 360 car seat features a 360° rotation function to facilitate the installation and removal of the child.

Rotation steps:

Press the rotation button (K) located on the seat
Gently turn the seat towards the door to install or remove the child
After finishing, turn the seat in both directions until it locks in the driving position

Important before each trip:

Before starting the vehicle, ensure that the seat is correctly locked in the driving position. Never drive with an unsecured or incompletely locked seat. If one side does not lock, try the locking maneuver again.

This rotation works with the support leg deployed and the seat can accommodate children from 40 to 105 cm.

Question 5

How to adjust the height and length of the harness?

Accepted Answer

The BabyGO Tojo car seat features a fully adjustable 5-point harness to accommodate your child's growth. The height adjustment has 3 available positions, while the length adjustment is done by tightening or lengthening the straps.

Adjusting the height of the harness:

To change the height, follow these steps:

Open the harness buckle located on the right side of the seat
Thread the end of the belt through the bottom opening on the side of the seat
Remove the tab from the belt buckle
Pull the end of the belt through the right slider of the straps on the backrest, then thread it into the left slider of the straps
To return to the previous position, repeat these steps in reverse order

For children in group 0+ (0 to 13 kg), use the lowest positions. For children in group 1 (9 to 18 kg), adjust the height so that the child's shoulders are level with the harness on the back.

Adjusting the length of the harness:

After securing your child and closing the buckle, the harness should be snug and flat against their body. To tighten the harness, press the button located between the child's legs, then simultaneously pull on the harness with your other hand. To lengthen the harness, press the same button and pull both straps towards you. Be sure to always pull the harness itself, never its cover.

Adjusting the crotch strap:

The crotch strap has 2 adjustable positions depending on your child's size. Place the seat in the maximum upright position, then pull the cover to access the buckle of the crotch strap. Reposition it to the desired height and close it with the tab.

Question 6

How to wash the reducer of the BabyGO GoSafe car seat?

Accepted Answer

The reducer of the BabyGO GoSafe car seat can be washed by following certain precautions to preserve the quality of the fabric and the safety of the seat:

Tips for washing the reducer:

Check the labels: Before washing, consult the care labels on the reducer for the manufacturer's specific recommendations.
Hand washing recommended: To avoid damaging the materials, prefer hand washing with lukewarm water and mild soap.
Avoid harsh products: Do not use detergents or harsh chemicals that could alter the fabric or the properties of the reducer.
Natural drying: Allow the reducer to air dry, away from direct sunlight, and avoid the dryer to prevent distorting or damaging the fabric.

By following these recommendations, you can effectively maintain the reducer of your BabyGO GoSafe seat while ensuring its durability and your child's safety.

User manual BabyGO : user manuals and guides in PDF

Models BabyGO most viewed

Browse manuals BabyGO by appliance type

Recent questions about devices BabyGO