Q: How to check the oil level of the engine on the Fuxtec FX-RM4346ECO lawn mower?

No, do not screw in the dipstick. The process is simple: Make sure the mower is level Remove the dipstick from the oil fill tube (do not screw it in) Insert the dipstick back into the tube Pull it out slowly to check the oil level Your mower uses oil of type SAE30 (FUXTEC 4MAX recommended) with a tank capacity of 0.5 L . Check this level before each use, and remember to change the oil every 25 hours of operation or at the start of each season.

Q: How to start the Fuxtec FX-RM5396PeSPRO?

The Fuxtec FX-RM5396PeSPRO is equipped with an electric starter. Here are the exact steps to get it started: Starting Procedure Hold the brake lever: Firmly press the brake lever (upper lever) against the handle with your left hand to keep the blade stationary. Press the start button: With your right hand, press the start button. The engine starts. Check the battery: Before starting, ensure that the battery is charged (at least 2 LED indicators lit on the charge indicator). Stopping the Engine To stop the engine, simply release the brake lever. Warning: The blade continues to spin for a few seconds after stopping - wait for it to come to a complete stop. Before Each Start Check the oil level Ensure there is fresh unleaded SP98 fuel in the tank Make sure the mowing area is free of debris

Q: Can you set a running time, or does the robot only have a start time?

You are correct: the Fuxtec FXRB224 does not have a programmable timer . It only has an automatic start time programming . Operation: You set the desired start time (using the HOME, START buttons and the arrows) The robot starts mowing at the programmed time It operates for 60 minutes maximum on a full charge (the battery charges in 120 minutes) Once the battery is empty, it automatically returns to its charging station It restarts the same cycle automatically 48 hours later In summary: no duration control. It is the battery that determines the operating time, capped at 60 minutes. The robot stops when the charge is exhausted.

Question 1

What is the brand and reference number of the spark plug for the FX-MS125?

Accepted Answer

The technical manual for the FX-MS125 does not specify the exact brand or reference number of the spark plug. However, it provides the complete specifications to identify and maintain your spark plug:

Gap: 0.6 to 0.7 mm (to be maintained and checked every 25 hours of use)
Tightening torque: 12 to 15 Nm

With this information, any dealer or specialized spare parts store can provide you with the compatible spark plug. To obtain the precise reference from the manufacturer Fuxtec, please contact customer service directly at info@fuxtec.fr mentioning your FX-MS125 model.

Question 2

What is the reference number for the belt of the Fuxtec FX-RM5196eSSL?

Accepted Answer

The reference numbers for the belt vary depending on the year of manufacture of your mower:

Models up to 2022: Reference 10000712
Models from 2023: Reference 10002261

To identify the correct number, check the year of manufacture indicated on the machine's label (usually on the engine casing or the frame). You can contact Fuxtec customer service by providing your serial number if you are unsure.

The drive belt connects the engine to the rear wheels for self-propulsion. This wear part can be replaced at an authorized Fuxtec dealer or through specialized garden equipment spare parts distributors.

Question 3

How to check the oil level of the engine on the Fuxtec FX-RM4346ECO lawn mower?

Accepted Answer

No, do not screw in the dipstick. The process is simple:

Make sure the mower is level
Remove the dipstick from the oil fill tube (do not screw it in)
Insert the dipstick back into the tube
Pull it out slowly to check the oil level

Your mower uses oil of type SAE30 (FUXTEC 4MAX recommended) with a tank capacity of 0.5 L. Check this level before each use, and remember to change the oil every 25 hours of operation or at the start of each season.

Question 4

How to start the Fuxtec FX-RM5396PeSPRO?

Accepted Answer

The Fuxtec FX-RM5396PeSPRO is equipped with an electric starter. Here are the exact steps to get it started:

Starting Procedure

Hold the brake lever: Firmly press the brake lever (upper lever) against the handle with your left hand to keep the blade stationary.
Press the start button: With your right hand, press the start button. The engine starts.
Check the battery: Before starting, ensure that the battery is charged (at least 2 LED indicators lit on the charge indicator).

Stopping the Engine

To stop the engine, simply release the brake lever. Warning: The blade continues to spin for a few seconds after stopping - wait for it to come to a complete stop.

Before Each Start

Check the oil level
Ensure there is fresh unleaded SP98 fuel in the tank
Make sure the mowing area is free of debris

Question 5

How to use the Fuxtec FX-RM4346ECO lawn mower?

Accepted Answer

Before you start

Check that the tank contains enough unleaded gasoline SP98 (capacity 0.8 L) and that the oil level is correct. Never use gasoline that is more than 30 days old.

Starting

Press the brake lever against the handle (safety bar)
Gently pull the starter cable until you feel resistance
Then pull the cable vigorously to start the engine

Basic use

Keep the brake lever pressed against the handle while mowing
The cutting width is 420 mm
Adjust the cutting height between 25 and 70 mm using the height controls on the wheels
Walk normally (do not run) with the device
The grass collection bag has a capacity of 40 liters - empty it regularly

Important safety

Always wear sturdy shoes and long pants
Keep children and pets at a distance
Never get your hands or feet near rotating parts
Stop the engine before any intervention or maintenance
Disconnect the spark plug wire before any maintenance work

Stopping

Release the brake lever to stop the engine. The blades will continue to spin for a few moments afterwards.

Question 6

How to assemble and operate the FX-RM5170PRO lawn mower?

Accepted Answer

Preparation before assembly: Remove the mower from its cardboard packaging and check that no loose parts are left in the packaging.

Wheel assembly: Using an M10 wrench, remove the four bolts from the four axles. Attach the two front wheels (18 cm) and the two rear wheels (23 cm) as indicated in the manual, then secure the four bolts. Next, install the front and rear wheel covers.

Handle assembly: Carefully unfold the handle, ensuring not to damage the control cables. Secure the different parts of the handle with the four wing nuts and washers provided. Insert the starter cable on the right side of the handle and secure it with the plastic handle. Then, insert the motor drive cable and the rear wheel drive cable into the corresponding holes of the lever (the arrow in the manual indicates where to attach the cables).

Panel and collection bin assembly: Secure the control panel with the two screws provided. Place the plastic edges of the collection bin onto the frame and secure the clips (a fill indicator will alert you when it is full). If you prefer mulching, the kit is integrated into the rear cover; fold down the cover to activate it.

Before first use: Important: the mower is delivered WITHOUT oil or gasoline. Fill with engine oil between the min/max marks on the oil gauge (capacity 0.5 L). Pour only unleaded gasoline SP98 up to a maximum of 1.0 L, filling to the lower edge of the limit in the neck of the tank, then tighten the cap. Use the cutting height adjustment lever (range 25-75 mm) with the engine off and the blade immobilized.

Starting the engine: Depending on the temperature, press the priming pump 1 to 4 times (1 time above 20°C, 2-3 times between 0-20°C, 3-4 times below 0°C). Pull the motor cable handle on the handle, then pull the starter cord sharply until the 4-stroke engine (2.9 kW, 170 cm³) starts; count 2-3 attempts if it is a cold start. Do not activate the rear wheel drive handle during starting, otherwise they will move.

Operation and stopping: Adjust the speed via the right handle of the dashboard among the 4 speeds (2.7 to 5.0 km/h). To stop, simply release the motor cable handle; the engine stops and the blade makes a few additional turns before coming to a halt. The mower covers up to 1,500 m² and its 60 L bin should be emptied regularly.

Question 7

How to adjust the carburetor of the Fuxtec FX-RM4180?

Accepted Answer

The manual for the Fuxtec FX-RM4180 states that carburetor adjustments should be made by a specialized workshop, and not by the user. Carburetor adjustments are delicate and require professional expertise to avoid damaging the engine or compromising performance.

Routine maintenance you can perform:

Regularly clean the air filter (especially in dusty environments)
Check the oil level before each use
Only use the recommended fuel: unleaded SP98 gasoline
Completely empty the tank if you do not use it for an extended period

If the mower starts difficultly, consumes too much gasoline, or has engine speed issues, consult a specialized workshop for a diagnosis and professional carburetor adjustment.

Question 8

How to prepare the grass collection bin before first use?

Accepted Answer

Yes, the collection bin of the FX-E2RM43 must be assembled and prepared correctly before its first use to ensure effective grass collection.

Assembling the bin frame: Start by opening the quick releases, then fold the lower bar. Check that the legs snap correctly into the designated slots. Then close the quick releases by turning them until they are securely fastened. Next, connect the upper bar to the lower bar using the provided body bolts and quick-release clamps.

Mounting the bin components: Take the plastic parts and the fabric of the collection basket and securely connect them to the frame. Ensure that all quick fasteners are tightly secured - you can adjust the positioning by turning the threaded screws clockwise or counterclockwise until a stable and secure closure is achieved.

Installation on the mower: Open the rear flap of the FX-E2RM43 and hang the fully assembled collection bin on the designated attachment points, as illustrated in the manual. Check that the bin clicks securely into position.

Checks before use: Once installed, visually inspect the bin to confirm that all components are properly aligned and that all fasteners are tight. The bin has a capacity of 40 liters - note this limit for regular emptying. Always completely stop the engine before installing, removing, or modifying the bin. Before each use, check that the bin is securely attached to the mower, as a faulty attachment prevents grass collection. Never open the rear flap while the engine is running.

Once these steps are completed, the collection bin is ready to operate and collect grass optimally during your first mowing.

Question 9

Why doesn't the grass go into the collection bin?

Accepted Answer

Essential Checks

If the grass does not fall into the bin despite following the instructions, first check these points:

Is the bin correctly assembled and secured? – According to the manual, the plastic parts and fabric must be connected to the frame of the collection bin as indicated in the manual. After emptying, the bin must be carefully reinstalled and secured to ensure proper attachment.
Is the bin's capacity exceeded? – The bin has a capacity of 40 liters. If it is full, the grass will not be collected. Empty it regularly.
Was the motor stopped before removal? – The manual emphasizes: before removing the collection bin, stop the motor and wait for the cutting bar to come to a complete stop.
Does the rear flap close completely? – Ensure that access to the bin opens and closes without obstruction.

Alternative: the mulching kit

If the collection bin is not functioning satisfactorily, your FX-E2RM43 mower comes with a mulching kit (included) that allows you to recycle the grass directly onto the lawn instead of collecting it. You can choose between collection and mulching according to your needs.

Question 10

Can you set a running time, or does the robot only have a start time?

Accepted Answer

You are correct: the Fuxtec FXRB224 does not have a programmable timer. It only has an automatic start time programming.

Operation:

You set the desired start time (using the HOME, START buttons and the arrows)
The robot starts mowing at the programmed time
It operates for 60 minutes maximum on a full charge (the battery charges in 120 minutes)
Once the battery is empty, it automatically returns to its charging station
It restarts the same cycle automatically 48 hours later

In summary: no duration control. It is the battery that determines the operating time, capped at 60 minutes. The robot stops when the charge is exhausted.

User manual Fuxtec Lawn mower : user manuals and guides in PDF

Models Fuxtec Lawn mower most viewed

Other categories Fuxtec

Recent questions about Lawn mower Fuxtec