Airblade 9kJ - Hand dryers DYSON - Free user manual and instructions
Find the device manual for free Airblade 9kJ DYSON in PDF.
| Product type | Hand dryer |
| Brand | Dyson |
| Model | Airblade 9kJ |
| Power supply | 220-240 V, 50/60 Hz, 3-wire cable (phase/neutral/ground) |
| Rated power | 900 W (adjustable to 650 W) |
| Operating mode | Automatic via infrared sensors |
| Drying technology | High-speed air blades |
| Filter | Washable and replaceable HEPA filter |
| Operating temperature | 0 °C to 40 °C |
| Maximum installation altitude | 2,300 m |
| Maximum cycle time | 30 seconds (automatic shut-off) |
| Daily maintenance | Wipe the sensors with a soft cloth and a non-abrasive cleaner |
| Filter maintenance | Regularly check the air intake; clean or replace the HEPA filter if obstructed (replacement kit available) |
| Installation | Wall-mounted, fixed on back plate, with rear or side cable entry |
| Tools required for installation | Cross-head and flat screwdrivers, drill, tape measure, wire strippers |
| Recommended mounting height | Indicated on the mounting template (adjustable according to installation) |
| Warranty | 5 years (parts and labor, subject to conditions) |
| Safety standards | Complies with local electrical codes; do not use jet cleaning equipment |
| Intended use | Hand drying only, indoors |
Frequently Asked Questions - Airblade 9kJ DYSON
User questions about Airblade 9kJ DYSON
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Hand dryers in PDF format for free! Find your manual Airblade 9kJ - DYSON and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Airblade 9kJ by DYSON.
USER MANUAL Airblade 9kJ DYSON
Installation instructions
GB/IE
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS APPLIANCE, READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND MAINTENANCE MANUAL.
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- This Dyson appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, only if they have been given supervision or instruction by a responsible person concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Before servicing or cleaning the appliance, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
- Do not use sealant when fixing the appliance to the wall.
- Do not install directly above a heating appliance.
- The maximum altitude of use is 2,300 metres.
- The size of the lead wire used for the wiring connection (including grounding lead) shall not be smaller than 18AWG.
DO NOT USE ANY JETWASH EQUIPMENT FOR CLEANING ON OR NEAR THIS APPLIANCE.
WARNING
ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN OR DYSON FIELD SERVICE ENGINEER IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
CAUTION
The appliance should be located indoors. Operating temperature range 0^ C ( 32^ F) to 40^ C ( 104^ F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this appliance to moisture.
Tools required
Suitable screwdriver for wall type fixings
Small Phillips screwdriver
Small flat head screwdriver
Dyson tool (supplied)
Tape measure and pencil
Hand drill
Suitable drill bit
Pliers/wire strippers
Knife
Pre-installation checks
Pre-installation planning
The machine is designed for a dry, internal location only.
Conformity and compliance is the responsibility of the installer. Consult
local and national accessibility codes and regulations for relevant installation guidelines.
Install the machine in compliance with all building codes and/or regulations.
Isolate the power supply before installation or service.
Make sure that no pipework (gas, water, air) or electrical cables, wires or ductwork are located directly behind the drilling/mounting area.
Select a location that will allow accessibility to the machine and proper clearance from surroundings and floor.
Make sure that there are no obstructions between the machine and the floor and at least 210mm above for filter removal.
Dyson recommends the use of protective clothing, eye wear and materials when installing/repairing as necessary.
Fig. A
Wall fixing requirements
Do not fix to unsupported plasterboard (drywall) as this will not provide a safe and secure installation for the machine and may also invalidate the guarantee.
Where only unsupported plasterboard is available for installation, a Dyson backplate must be used. Contact the Dyson Helpline for further information.
If the wall has an airgap, the fixings used must be of a sufficient length to provide a secure installation.
Don't use sealant when fixing the machine to the wall.
Fig. B
Power modes
This Dyson Airblade™ hand dryer has two power modes, 900W and 650W. The machine is set to 900W as default. If required, change the power mode to 650W before installation.
For more information about the power modes, go to www.dyson.com/airblade
Electrical
Input voltage/frequency: refer to rating plate.
Make sure that the power supply is switched off before installing.
Cable specification: 3 core cable (live/neutral/earth).
Local electrical regulations must be adhered to when installing or repairing this machine.
Rated power: refer to rating plate.
Operating temperature range: 0°C to 40°C.
Maximum length of strip-back of Live and Neutral wire insulation: 7mm.
Quality testing
The Dyson Airblade™ hand dryer has undergone extensive quality testing, to make sure it can withstand forces and impacts typical of a commercial and public bathroom environment.
Installing the Dyson Airblade™ hand dryer
WARNING: Risk of electric shock!
Ensure that the power supply is switched off before continuing.
Fig. 1
Drill the mounting holes
Select the installation location and appropriate height.
Recommended mounting heights are shown on the Mounting template. It may be necessary to adjust the measurements for individual installations.
Fix the supplied Mounting template to the wall in the correct location.
Rear cable entry installation: the electricity supply cable must align from the wall to the entry point on the Mounting template.
Side cable entry installation: an additional hole will need drilling. Refer to the Mounting template for location.
Drill the holes, where marked, using a suitable drill bit.
Fig. 2
For rear cable entry installation
Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the pre-installed earth wire remains in place.
Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don't remove the gland from the backplate.
Using suitable fixings (not countersunk screws), fix the backplate to the wall.
Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the pre-installed earth wire remains securely inserted into the connector block.
Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
Only clamp double insulated cables with the cable clamp.
Don't overtighten any of the electrical fixtures.
Fig. 3 For side cable entry installation
Using suitable fixings (not countersunk screws), fix the backplate to the wall.
Identify which side the cable will enter. Unscrew the entry tab on the machine.
Cut the rubber side tab of the conduit box on the side that will be facing downwards after installation.
Use a suitable cable gland/conduit connector (not supplied) for the installation.
Secure the conduit box on the wall using suitable fixings.
Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the pre-installed earth wire remains in place.
Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don't remove the gland from the backplate.
Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the pre-installed earth wire remains securely inserted into the connector block.
Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
Only clamp double insulated cables with the cable clamp.
Don't overtighten any of the electrical fixtures.
Fig. 4 Install the main body
This Dyson Airblade™ hand dryer has two power modes, 900W and 650W. The machine is set to 900W as default. If required, change the power mode to 650W before installation.
Hook the machine on to the backplate and gently lower the bottom of the machine until it is flush with the wall. Check that both backplate hooks are securely in position before continuing.
Fix the 2 security screws into the bottom of the machine using the tool supplied.
Fig. 5 Complete the installation
Place the filter unit in the machine and make sure it clicks securely into place. Turn on the mains power supply and test the machine is working as it should by placing hands in sight of the sensors.
Please hand this manual to the owner/facilities manager.
Maintenance
GB/IE
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS APPLIANCE, READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND MAINTENANCE MANUAL.
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- This Dyson appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, only if they have been given supervision or instruction by a responsible person concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Do not allow the appliance to be used for any purpose other than drying hands. Use this appliance only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
- Before servicing or cleaning the appliance, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
- The maximum altitude of use is 2,300 metres.
DO NOT USE ANY JETWASH EQUIPMENT FOR CLEANING ON OR NEAR THIS APPLIANCE.
WARNING
ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN OR DYSON FIELD SERVICE ENGINEER IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
CAUTION
The appliance should be located indoors. Operating temperature range 0^ C ( 32^ F) to 40^ C ( 104^ F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this appliance to moisture.
Looking after your hand dryer
Please register as a Dyson hand dryer owner
To help us ensure you receive a prompt and efficient service, please register your machine at www.dyson.com/airblade. This will register your guarantee, confirm ownership of your Dyson machine in the event of an insurance loss, and enable us to contact you if necessary.
You will need your serial number, which can be found on the rating plate inside the main body and on the information sticker on the front of the machine.
Please ensure all instructions and guidance in the Installation instructions and Maintenance manual are adhered to or your guarantee may be invalidated.
Maintenance
How to use
Place your hands beneath the Dyson Airblade™ hand dryer arms and it will start automatically, creating sheets of air that scrape water from your hands.
For best dry time results:
Keep your hands flat and parallel to the machine's surface, approximately 5mm from the air aperture, drawing your hands through the airflow from your wrists to finger tips.
Move your hands slowly through the airflow, keeping a consistent speed (approx. 2.5 seconds per side), alternating between front and back each time.
Keep your hands flat, close the gaps between your fingers and keep your thumbs tucked in, so the whole of your hand is drawn through the airflow.
For more information about the power modes, go to www.dyson.com/airblade
Troubleshooting
Hand dryer cuts out
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Turn the machine off and on again at the mains electricity supply.
Make sure the sensors are clean.
Check the air apertures are clean and free of dust and blockages. If the air apertures are dusty, simply remove dust.
Check that the air inlet is free from blockages.
Dry time has increased
Make sure that the correct power mode has been selected.
Check that the air inlet is free from blockages.
Inspect the air apertures for dust, and remove.
Airflow is running hotter than usual
Check that the air inlet is free from blockages.
Inspect the air apertures for dust, and remove.
Air is continuously running
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Check that the air inlet is free from blockages.
Inspect the air apertures for dust, and remove.
Contact Dyson for further support and information or online at www.dyson.com/airblade
Cleaning
The hand dryer should be cleaned daily.
Wipe the sensors using a soft cloth and non-abrasive cleaner.
Important information
Don't pressure wash the machine.
All cleaning chemicals should be used exactly as indicated by the manufacturer's instructions (including appropriate dilution).
Any chemicals intended for use should first be tested on an inconspicuous area to confirm suitability. Aside from cleaning chemicals, care should be taken to avoid any harmful fluids from coming into contact with the machine, in particular oils and alcohol-based products.
Filter maintenance
Regularly check the air inlet to ensure that it is free from dust and debris. Simply wiping the inlet with a soft cloth should be sufficient to remove dust and debris.
If the air inlet gets clogged, further cleaning or a filter change might be required.
If required for high usage environments, a Dyson filter change kit provides everything needed to change your machine's HEPA filter on site. Contact the Dyson Helpline for more information.
Filter cleaning or replacement for your hand dryer can be carried out by carefully following the instructions given in the filter change kit. If in any doubt, consult a qualified electrician or contact the Dyson Helpline for support.
Servicing
If your hand dryer needs servicing, please call the Dyson Helpline or visit the website at www.dyson.com/airblade
Additional information
Disposal information
- Dyson products are made from high grade recyclable materials. Recycle where possible.
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.
Your guarantee
Terms and conditions of the Dyson
5 year guarantee
- If you have registered your machine online, your guarantee will start from the date of purchase. Please retain your proof of purchase. If you do not have your proof of purchase, your guarantee will start 90 days after the date of manufacture, according to Dyson's records.
- Where this machine is sold within the EU, this guarantee will only be valid (i) if the machine is installed and used in the country in which it was sold or (ii), if the machine is installed and used in Austria, Belgium, France, Germany, Ireland, Italy, Netherlands, Spain or the United Kingdom and the same model as this machine is sold at the same voltage rating in the relevant country. Where this machine is sold outside of the EU, this guarantee will only be valid if the machine is installed and used in the country in which it was sold.
What is covered
- All factory parts of your hand dryer are guaranteed against original defects, material and workmanship when used in accordance with the Dyson manual for a period of 5 years from the start of your guarantee.
- Please call the Dyson Helpline for more information.
- Where Dyson determines that the main body assembly needs replacing, Dyson will send a replacement to be fitted by the customer on site. The customer will need to return any defective parts to Dyson using the prepaid postage box provided.
- Any replaced parts must be returned to Dyson or an administration fee will be levied.
- Where a filter change is required, Dyson will provide a filter change kit to be installed on site by the customer.
- Any parts which are returned and replaced by Dyson will become the property of Dyson.
- The replacement of any part of your machine under guarantee will not extend the period of guarantee.
- The guarantee provides benefits which are additional to and do not affect any statutory rights you may have as a consumer.
What is not covered
Dyson does not guarantee the repair or replacement of a product as a result of:
- Accidental damage, faults caused by negligent use or care, unintentional or deliberate misuse, neglect, vandalism, careless operation or handling of the machine which is not in accordance with the Dyson manual.
- Use of parts not assembled or installed in accordance with the instructions of Dyson.
- Use of parts and accessories which are not genuine Dyson components.
- Faulty installation, or installation that does not precisely follow the installation instructions supplied by Dyson (except where installed by Dyson).
- Repairs or alterations carried out other than in accordance with instructions by Dyson.
- Damage from external sources such as transit, weather, electrical outages or power surges.
• Normal wear and tear (e.g. fuse, etc.). - Damage caused by cleaning which is not in line with the instructions in the manual.
- Damage caused by water ingress due to cleaning or treatment prohibited in the manual.
- Any electrical, flooding or structural damage, or any loss of business or revenue as a result of product failure. If you are in any doubt as to what is covered by your guarantee, please contact Dyson.
Summary of cover
- You must provide proof of (both the original and any subsequent) delivery/purchase before any work can be carried out on your Dyson machine or before any replacement ports will be supplied. Without this proof, any work carried out or parts supplied will be chargeable. Keep your receipt or delivery note.
- Subject to the exclusions above, all work to be carried out under this guarantee will be carried out by Dyson or its authorised agents.
Important data protection information
When registering your Dyson machine:
- You will need to provide us with basic contact information to register your machine and enable us to support your guarantee.
- When you register, you will have the opportunity to choose whether you would like to receive communications from us. If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
• We never sell your information to third parties and only use information that you share with us as defined by our privacy policies which are available on our website: privacy.dyson.com
Installation instructions
AU/NZ
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND MAINTENANCE MANUAL.
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Before servicing or cleaning the appliance, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
- Do not use sealant when fixing the appliance to the wall.
- Do not install directly above a heating appliance.
- The maximum altitude of use is 2,300 metres.
- The size of the lead wire used for the wiring connection (including grounding lead) shall not be smaller than 18AWG.
DO NOT USE ANY JETWASH EQUIPMENT FOR CLEANING ON OR NEAR THIS APPLIANCE.
WARNING
ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
CAUTION
Your hand dryer should be located indoors. Operating temperature range 0^ C ( 32^ F) to 40^ C ( 104^ F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this appliance to moisture.
Tools required
Suitable screwdriver for wall type fixings
Small Phillips screwdriver
Small flat head screwdriver
Dyson tool (supplied)
Tape measure and pencil
Hand drill
Suitable drill bit
Pliers/wire strippers
Knife
Pre-installation checks
Pre-installation planning
The machine is designed for a dry, internal location only.
Conformity and compliance is the responsibility of the installer. Consult
local and national accessibility codes and regulations for relevant installation guidelines.
Install the machine in compliance with all building codes and/or regulations.
Isolate the power supply before installation or service.
Ensure no pipe work (gas, water, air) or electrical cables, wires or ductwork are located directly behind the drilling/mounting area.
Select a location that will allow accessibility to the machine and proper clearance from surroundings and floor.
Make sure that there are no obstructions between the machine and the floor and at least 210mm above for filter removal.
Dyson recommends the use of protective clothing, eyeware and materials when installing/repairing as necessary.
Fig. A
Wall fixing requirements
Do not fix to unsupported plasterboard (drywall) as this will not provide a safe and secure installation for the machine and may also invalidate the guarantee.
Where only unsupported plasterboard is available for installation, a Dyson backplate must be used. Contact the Dyson Helpline for further information.
If the wall has an airgap, the fixings used must be of a sufficient length to provide a secure installation.
Do not use sealant when fixing the machine to the wall.
Fig. B
Power modes
This Dyson Airblade™ hand dryer has two power modes, 900W and 650W. The machine is set to 900W as default. If required, change the power mode to 650W before installation.
For more information about the power modes, go to www.dyson.com/airblade
Electrical
Input voltage/Frequency: refer to rating plate.
Make sure that the power supply is switched off before installing.
Cable specification: 3 core cable (live/neutral/earth).
Local electrical regulations must be adhered to when installing or repairing this machine.
Rated power: refer to rating plate.
Operating temperature range: 0°C to 40°C.
Maximum length of strip-back of Live and Neutral wire insulation: 7mm.
Quality testing
The Dyson Airblade™ hand dryer has undergone extensive quality testing, to make sure it can withstand forces and impacts typical of a commercial and public bathroom environment.
Installing the Dyson Airblade™ hand dryer
WARNING: Risk of electric shock!
Ensure that the power supply is switched off before continuing.
Fig. 1
Drill the mounting holes
Select the installation location and appropriate height.
Recommended mounting heights are shown on the Mounting template. It may be necessary to adjust the measurements for individual installations.
Fix the supplied Mounting template to the wall in the correct location.
Rear cable entry installation: the electricity supply cable must align from the wall to the entry point on the Mounting template.
Side cable entry installation: an additional hole will need drilling. Refer to the Mounting template for location.
Drill the holes, where marked, using a suitable drill bit.
Fig. 2
For rear cable entry installation
Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the pre-installed earth wire remains in place.
Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don't remove the gland from the backplate.
Using suitable fixings (not countersunk screws), fix the backplate to the wall.
Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the pre-installed earth wire remains securely inserted into the connector block.
Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
Only clamp double insulated cables with the cable clamp.
Don't overtighten any of the electrical fixtures.
Fig. 3 For side cable entry installation
Using suitable fixings (not countersunk screws), fix the backplate to the wall.
Identify which side the cable will enter. Unscrew the entry tab on the machine.
Cut the rubber side tab of the conduit box on the side that will be facing downwards after installation.
Use a suitable cable gland/conduit connector (not supplied) for the installation.
Secure the conduit box on the wall using suitable fixings.
Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the pre-installed earth wire remains in place.
Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don't remove the gland from the backplate.
Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the pre-installed earth wire remains securely inserted into the connector block.
Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
Only clamp double insulated cables with the cable clamp.
Don't overtighten any of the electrical fixtures.
Fig. 4 Install the main body
This Dyson Airblade™ hand dryer has two power modes, 900W and 650W. The machine is set to 900W as default. If required, change the power mode to 650W before installation.
Hook the machine on to the backplate and gently lower the bottom of the machine until it is flush with the wall. Check that both backplate hooks are securely in position before continuing.
Fix the 2 security screws into the bottom of the machine using the tool supplied.
Fig. 5 Complete the installation
Place the filter unit in the machine and make sure it clicks securely into place. Turn on the mains power supply and test the machine is working as it should by placing hands in sight of the sensors.
Please hand this manual to the owner/facilities manager.
Maintenance
AU/NZ
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND MAINTENANCE MANUAL.
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Do not allow the appliance to be used for any purpose other than drying hands. Use this appliance only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
- Before servicing or cleaning the appliance, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
- The maximum altitude of use is 2,300 metres.
DO NOT USE ANY JETWASH EQUIPMENT FOR CLEANING ON OR NEAR THIS APPLIANCE.
WARNING
ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
CAUTION
Your hand dryer should be located indoors. Operating temperature range 0^ C ( 32^ F) to 40^ C ( 104^ F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this appliance to moisture.
Looking after your hand dryer
Please register as a Dyson hand dryer owner
To help us ensure you receive a prompt and efficient service, please register your machine at www.dyson.com/airblade. This will register your guarantee, confirm ownership of your Dyson machine in the event of an insurance loss, and enable us to contact you if necessary.
You will need your serial number, which can be found on the rating plate inside the main body and on the information sticker on the front of the machine.
Please ensure all instructions and guidance in the Installation instructions and Maintenance manual are adhered to or your guarantee may be invalidated.
Maintenance
How to use
Place your hands beneath the Dyson Airblade™ hand dryer arms and it will start automatically, creating sheets of air that scrape water from your hands.
For best dry time results:
Keep your hands flat and parallel to the machine's surface, approximately 5mm from the air aperture, drawing your hands through the airflow from your wrists to finger tips.
Move your hands backwards and forwards slowly through the air, turning them over so both back and front are exposed to the airflow.
Keep your hands flat, close the gaps between your fingers and keep your thumbs tucked in, so the whole of your hand is drawn through the airflow.
For more information about the power modes, go to www.dyson.com/airblade
Troubleshooting
Hand dryer cuts out
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Turn the machine off and on again at the mains electricity supply.
Make sure the sensors are clean.
Check the air apertures are clean and free of dust and blockages. If the air apertures are dusty, simply remove dust.
Check that the air inlet is free from blockages.
The dry time has increased
Make sure that the correct power mode has been selected.
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
The airflow is running hotter than usual
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
Air is continuously running
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
Contact Dyson for further support and information or online at www.dyson.com/airblade
Cleaning
The hand dryer should be cleaned daily.
Wipe the sensors using a soft cloth and non-abrasive cleaner.
Important information
Do not pressure wash the machine.
All cleaning chemicals should be used exactly as indicated by the manufacturer's instructions (including appropriate dilution).
Any chemicals intended for use should first be tested on an inconspicuous area to confirm suitability. Aside from cleaning chemicals, care should be taken to avoid any harmful fluids from coming into contact with the product, in particular oils and alcohol-based products.
Filter maintenance
Regularly check the air inlet to ensure that it is free from dust and debris. Simply wiping the inlet with a soft cloth should be sufficient to remove dust and debris.
If the air inlet gets clogged, further cleaning or a filter change might be required.
If required for high usage environments, a Dyson filter change kit provides everything needed to change your machine's HEPA filter on site. Contact the Dyson Helpline for more information.
Filter cleaning or replacement for your hand dryer can be carried out by carefully following the instructions given in the filter change kit. If in any doubt, consult a qualified electrician or contact the Dyson Helpline for support.
Servicing
If your hand dryer needs servicing, please call the Dyson Helpline or visit the website at www.dyson.com/airblade
Additional information
Disposal information
Dyson products are made from high grade recyclable materials. Recycle where possible.
When your Dyson machine reaches the end of its life, we are responsible for its safe disposal. You can send your old Dyson machine back to us and we will organise for it to be recycled. Please note that not all parts are recyclable. Recycling of parts is subject to the capabilities of 3rd party suppliers. Available in Australia only.
Simply:
- Box up your old Dyson machine.
- Either post or drop off to the address below.
Dyson We Recycle
Dyson Service Centre
8-10 Mangrove Lane
Taren Point, NSW 2229
Your guarantee
Terms and conditions of the Dyson 5 year guarantee
- If you have registered your machine online, your guarantee will start from the date of purchase. Please retain your proof of purchase. If you do not have your proof of purchase, your guarantee will start 90 days after the date of manufacture, according to Dyson's records.
- This guarantee will be void if the machine is installed and used in a country outside the one in which it was sold.
- The Dyson Guarantee does not affect your statutory rights as a consumer, including under the Australian Consumer Law. In some circumstances it may provide additional benefits.
What is covered
- All factory parts of your hand dryer are guaranteed against original defects, material and workmanship when used in accordance with the Dyson manual for a period of 5 years from the start of your guarantee.
- Please call the Dyson Helpline for more information.
- Where Dyson determines that the main body assembly needs replacing, Dyson will send a replacement to be fitted by the customer on site. The customer will need to return any defective parts to Dyson using the prepaid postage box provided.
- Any replaced parts must be returned to Dyson or an administration fee will be levied.
- Where a filter change is required, Dyson will provide a filter change kit to be installed on site by the customer.
- Any parts which are returned and replaced by Dyson will become the property of Dyson.
- The replacement of any part of your machine under guarantee will not extend the period of guarantee.
- The Dyson Guarantee does not affect your statutory rights as a consumer, including under the Australian Consumer Law. In some circumstances it may provide additional benefits.
What is not covered
Dyson does not guarantee the repair or replacement of a product as a result of:
- Accidental damage, faults caused by negligent use or care, unintentional or deliberate misuse, neglect, vandalism, careless operation or handling of the
fixture which is not in accordance with the Dyson manual.
- Use of parts not assembled or installed in accordance with the instructions of Dyson.
- Use of parts and accessories which are not genuine Dyson components.
- Faulty installation, or installation that does not precisely follow the installation instructions supplied by Dyson (except where installed by Dyson).
• Repairs or alterations carried out other than in accordance with instructions by Dyson.
- Damage from external sources such as transit, weather, electrical outages or power surges.
• Normal wear and tear (e.g. fuse, etc.).
- Damage caused by cleaning which is not in line with the instructions in the Dyson manual.
- Damage caused by water ingress due to cleaning or treatment prohibited in the Dyson manual.
- Any electrical, flooding or structural damage, or any loss of business or revenue as a result of product failure. If you are in any doubt as to what is covered by your guarantee, please contact Dyson.
Summary of cover
- You must provide proof of (both the original and any subsequent) delivery/purchase before any work can be carried out on your Dyson machine or before any replacement ports will be supplied. Without this proof, any work carried out or parts supplied will be chargeable. Keep your receipt or delivery note.
- Subject to the exclusions above, all work to be carried out under this guarantee will be carried out by Dyson or its authorised agents.
Important data protection information
When registering your Dyson machine:
- You will need to provide us with basic contact information to register your machine and enable us to support your Dyson guarantee.
- When you register, you will have the opportunity to choose whether you would like to receive communications from us. If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
• We never sell your information to third parties and only use information that you share with us as defined by our privacy policies which are available on our website: privacy.dysan.com
Installation instructions
CA
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND THE MAINTENANCE MANUAL.
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- This Dyson appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Before servicing or cleaning the appliance, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
- Do not use sealant when fixing the appliance to the wall.
- Do not install directly above a heating appliance.
- The maximum altitude of use is 2,300 metres.
- The size of the lead wire used for the wiring connection (including grounding lead) shall not be smaller than 18AWG.
DO NOT USE ANY JETWASH EQUIPMENT FOR CLEANING ON OR NEAR THIS APPLIANCE.
WARNING
ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
CAUTION
Your hand dryer should be located indoors. Operating temperature range 0^ C ( 32^ F) to 40^ C ( 104^ F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this appliance to moisture.
Tools required
Suitable screwdriver for wall type fixings
Small Phillips screwdriver
Small flat head screwdriver
Dyson tool (supplied)
Tape measure and pencil
Hand drill
Suitable drill bit
Pliers/wire strippers
Knife
Pre-installation checks
Pre-installation planning
The machine is designed for a dry, internal location only. Conformity and compliance is the responsibility of the installer. Consult local and national accessibility codes and regulations for relevant installation guidelines. Install the machine in compliance with all building codes and/or regulations. Isolate the power supply before installation or service. Ensure no pipe work (gas, water, air) or electrical cables, wires or ductwork are located directly behind the drilling/mounting area. Select a location that will allow accessibility to the machine and proper clearance from surroundings and floor. Make sure that there are no obstructions between the machine and the floor and at least 210mm (8.3 inches) above for filter removal. Dyson recommends the use of protective clothing, eye wear and materials when installing/repairing as necessary.
Fig. A
Wall fixing requirements
Do not fix to unsupported plasterboard (drywall) as this will not provide a safe and secure installation for the machine and may also invalidate the guarantee.
Where only unsupported plasterboard is available for installation, a Dyson backplate must be used. Contact the Dyson Helpline for further information.
If the wall has an airgap, the fixings used must be of a sufficient length to provide a secure installation.
Do not use sealant when fixing the machine to the wall.
Fig. B
Power modes
This Dyson Airblade™ hand dryer has two power modes, 900W and 650W. The machine is set to 900W as default. If required, change the power mode to 650W before installation.
For more information about the power modes, go to www.dyson.com/airblade
Electrical
Input voltage/Frequency: refer to rating plate.
Make sure that the power supply is switched off before installing.
Cable specification: 3 core cable (live/neutral/earth).
Local electrical regulations must be adhered to when installing or repairing this machine.
Rated power: refer to rating plate.
Operating temperature range: 0°C to 40°C.
Maximum length of strip-back of Live and Neutral wire insulation: 7mm (0.3 inches).
Quality testing
The Dyson Airblade ^™ hand dryer has undergone extensive quality testing, to make sure it can withstand forces and impacts typical of a commercial and public bathroom environment.
Installing the Dyson Airblade™ hand dryer
WARNING: Risk of electric shock!
Ensure that the power supply is switched off before continuing.
Fig. 1
Drill the mounting holes
Select the installation location and appropriate height.
Recommended mounting heights are shown on the Mounting template. It may be necessary to adjust the measurements for individual installations.
Fix the supplied Mounting template to the wall in the correct location.
Rear cable entry installation: the electricity supply cable must align from the wall to the entry point on the Mounting template.
Side cable entry installation: an additional hole will need drilling. Refer to the Mounting template for location.
Drill the holes, where marked, using a suitable drill bit.
Fig. 2
For rear cable entry installation
Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the pre-installed earth wire remains in place.
Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don't remove the gland from the backplate.
Using suitable fixings (not countersunk screws), fix the backplate to the wall.
Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the pre-installed earth wire remains securely inserted into the connector block.
Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
Only clamp double insulated cables with the cable clamp.
Don't overtighten any of the electrical fixtures.
Fig. 3 For side cable entry installation
Using suitable fixings (not countersunk screws), fix the backplate to the wall.
Identify which side the cable will enter. Unscrew the entry tab on the machine.
Cut the rubber side tab of the conduit box on the side that will be facing downwards after installation.
Use a suitable cable gland/conduit connector (not supplied) for the installation.
Secure the conduit box on the wall using suitable fixings.
Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the pre-installed earth wire remains in place.
Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don't remove the gland from the backplate.
Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the pre-installed earth wire remains securely inserted into the connector block.
Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
Only clamp double insulated cables with the cable clamp.
Don't overtighten any of the electrical fixtures.
Fig. 4 Install the main body
This Dyson Airblade™ hand dryer has two power modes, 900W and 650W. The machine is set to 900W as default. If required, change the power mode to 650W before installation.
Hook the machine on to the backplate and gently lower the bottom of the machine until it is flush with the wall. Check that both backplate hooks are securely in position before continuing.
Fix the 2 security screws into the bottom of the machine using the tool supplied.
Fig. 5 Complete the installation
Place the filter unit in the machine and make sure it clicks securely into place. Turn on the mains power supply and test the machine is working as it should by placing hands in sight of the sensors.
Please hand this manual to the owner/facilities manager.
Maintenance
CA
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND THE MAINTENANCE MANUAL.
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- This Dyson appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Do not allow the appliance to be used for any purpose other than drying hands. Use this appliance only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
- Before servicing or cleaning the appliance, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
- The maximum altitude of use is 2,300 metres.
DO NOT USE ANY JETWASH EQUIPMENT FOR CLEANING ON OR NEAR THIS APPLIANCE.
WARNING
ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
CAUTION
Your hand dryer should be located indoors. Operating temperature range 0^ C ( 32^ F) to 40^ C ( 104^ F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this appliance to moisture.
Looking after your hand dryer
Please register as a Dyson hand dryer owner
To help us ensure you receive a prompt and efficient service, please register your machine at www.dyson.com/airblade. This will register your warranty, confirm ownership of your Dyson machine in the event of an insurance loss, and enable us to contact you if necessary.
You will need your serial number, which can be found on the rating plate inside the main body and on the information sticker on the front of the machine.
Please ensure all instructions and guidance in the Installation instructions and Maintenance manual are adhered to or your warranty may be invalidated.
Maintenance
How to use
Place your hands beneath the Dyson Airblade™ hand dryer arms and it will start automatically, creating sheets of air that scrape water from your hands.
For best dry time results:
Keep your hands flat and parallel to the machine's surface, approximately 5mm from the air aperture, drawing your hands through the airflow from your wrists to finger tips.
Move your hands backwards and forwards slowly through the air, turning them over so both back and front are exposed to the airflow.
Keep your hands flat, close the gaps between your fingers and keep your thumbs tucked in, so the whole of your hand is drawn through the airflow.
For more information about the power modes, go to www.dyson.com/airblade
Troubleshooting
Hand dryer cuts out
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Turn the machine off and on again at the mains electricity supply.
Make sure the sensors are clean.
Check the air apertures are clean and free of dust and blockages. If the air apertures are dusty, simply remove dust.
Check that the air inlet is free from blockages.
The dry time has increased
Make sure that the correct power mode has been selected.
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
The airflow is running hotter than usual
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
Air is continuously running
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
Contact Dyson for further support and information or online at www.dyson.com/airblade
Cleaning
The hand dryer should be cleaned daily.
Wipe the sensors using a soft cloth and non-abrasive cleaner.
Important information
Do not pressure wash the appliance.
All cleaning chemicals should be used exactly as indicated by the manufacturer's instructions (including appropriate dilution).
Any chemicals intended for use should first be tested on an inconspicuous area to confirm suitability. Aside from cleaning chemicals, care should be taken to avoid any harmful fluids from coming into contact with the product, in particular oils and alcohol-based products.
Filter maintenance
Regularly check the air inlet to ensure that it is free from dust and debris. Simply wiping the inlet with a soft cloth should be sufficient to remove dust and debris.
If the air inlet gets clogged, further cleaning or a filter change might be required.
If required for high usage environments, a Dyson filter change kit provides everything needed to change your machine's HEPA filter on site. Contact the Dyson Helpline for more information.
Filter cleaning or replacement for your hand dryer can be carried out by carefully following the instructions given in the filter change kit. If in any doubt, consult a qualified electrician or contact the Dyson Helpline for support.
Servicing
If your hand dryer needs servicing, please call the Dyson Helpline or visit the website at www.dyson.com/airblade
Additional information
Disposal information
- Dyson products are made from high grade recyclable materials. Recycle where possible.
Your warranty
Terms and conditions of the Dyson 5 year limited warranty
- If you have registered your machine online, your warranty will start from the date of purchase. Please retain your proof of purchase. If you do not have your proof of purchase, your warranty will start 90 days after the date of manufacture, according to Dyson's records.
- This warranty will be void if the machine is installed and used in a country outside the one in which it was sold.
What is covered
- All factory parts of your hand dryer are warranted against original defects, material and workmanship when used in accordance with the Dyson manual for a period of 5 years from the start of your warranty.
- Where Dyson determines that the main body assembly needs replacing, Dyson will send a replacement to be fitted by the customer on site. The customer will need to return any defective parts to Dyson using the prepaid postage box provided.
- Any replaced parts must be returned to Dyson or an administration fee will be levied.
- Please call the Dyson Helpline for more information.
- Any parts which are returned and replaced by Dyson will become the property of Dyson.
- The replacement of any part of your machine under warranty will not extend the period of warranty.
- This warranty provides benefits which are additional to and do not affect any statutory rights you may have as a consumer.
What is not covered
Dyson Canada Limited shall not be liable for costs, damages or repairs incurred as a result of, due to, or from:
• Purchases of machines from unauthorized dealers.
- Careless operation or handling, misuse, abuse and/or lack of maintenance or use not in accordance with the Dyson manual.
- Use of parts not assembled or installed in accordance with the instructions of Dyson.
- Use of parts and accessories which are not genuine Dyson components.
- Faulty installation, or installation that does not precisely follow the installation instructions supplied by Dyson (except where installed by Dyson).
- Repairs or alterations carried out other than in accordance with instructions by Dyson.
- Damage from external sources such as transit, weather, electrical outages or power surges.
• Normal wear and tear (e.g. fuse, etc.).
- Damage caused by cleaning which is not in line with the instructions in the Dyson manual. Do not use chemicals to clean the machine.
- Damage caused by water ingress due to cleaning or treatment prohibited in the Dyson manual.
- Any electrical, flooding or structural damage, or any loss of business or revenue as a result of product failure.
If you are in any doubt as to what is covered by your warranty, please contact Dyson.
Warranty limitations and exclusions
- Any implied warranties relating to your machine including but not limited to warranty of merchantability or warranty of fitness for a particular purpose, are limited to the duration of this warranty. This limitation is not allowed by some Provinces and/or Territories and so this limitation may not apply to you.
- Your remedy for breach of this warranty is limited to the warranty service described above.
- Dyson Canada Limited will not be liable for any consequential damages or incidental damages you may incur in connection with the purchase and use of your machine.
- This limited warranty gives you specific legal rights. You may also have other rights which vary by Province and/or Territory.
• This limited warranty is not transferable. - This limited warranty is only available in Canada.
Important data protection information
When registering your Dyson machine:
- You will need to provide us with basic contact information to register your machine and enable us to support your warranty.
- When you register, you will have the opportunity to choose whether you would like to receive communications from us. If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
• We never sell your information to third parties and only use information that you share with us as defined by our privacy policies which are available on our website at privacy.dyson.com
O: Indicate that this hazardous substance contained in all of the homogeneous materials for this part is within the limit requirement in GB/T 26572 O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下
X: Indicate that this hazardous substance contained in at least one of the homogeneous materials used for this part exceed the limit requirement in GB/T26572 X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572定的限量要求
(1) Hazardous substance contained is exempted under EU RoHS directives exemption list (2011/65/EU).
(1) 部件材质中有害物质含量符合欧盟RoHS指令豁免项目的限值(2011/65/EU)。
Disclaimer:
The environment safe use period is declared based on the normal temperature & humidity used conditions.
声明：
环保使用期限的参考标识取决于产品正常工作的温度和湿度等条件。
维护
CN
阅读并保存这些说明 重要安全说明
Note 1: "O" Indicate that the percentage content of the restricted substance does not exceed the
percentage of reference value of presence
Note 2: “-” indicates that the restricted substance corresponds to the exemption
Note 3: "Exceeding 0.1 wt%" and "exceeding 0.01 wt%" indicate that the percentage content of
the restricted substance exceeds the reference percentage value of presence condition
維護
TW/HK
Outil Dyson (fourni)
When using an electrical appliance, basic precautions should always be followed, including the following:
! VIDVÖRUN
FYLGIĐ EFTIRFARANDI VARÚĐARRÁĐSTÖFUNUM TIL AD DRAGA ÚR ELDHÆTTU, HÆTTU Á RAFLOSTI EĐA MEIDSLUM:
When using an electrical appliance, basic precautions should always be followed, including the following:
! VIDVÖRUN
FYLGIĐ EFTIRFARANDI VARÚĐARRÁĐSTÖFUNUM TIL AD DRAGA ÚR ELDHÆTTU, HÆTTU Á RAFLOSTI EĐA MEIDSLUM:
또한 www.dyson.com/airblade
웹사이트를 방문하십시오.
추가 정보
폐기 정보
Skrujern for veggfester
Lite stjerneskrujern
Liten flathodet skrutrekker
Dyson-verkløy (medfølger)
Målebånd og blyant
Håndbor
Passende bor
Tang/avisoleringstang
Kniv
Fix the 2 security screws into the bottom of the machine using the tool supplied.
Figur 5
DÔLEŽITÉ BEZPEČNOSTNÉ POKYNY
PRED MONTÁŽOU ALEBO POUŽITÍM TOHTO ZARIADENIA SI PREČÍTAJTE VŠETKY POKYNY A VAROVNÉ OZNAČENIA UVEDENÉ V MONTÁŽNYCH POKYNOCH A V NÁVODE NA ÚDRŽBU.
The image is too blurry to recognize any text content.
วิทยาลัยนิยม
^1 ^2 ^3 ^4 ^5 ^6 ^7 ^8
[Unreadable]
87164
The source image is illegible due to extreme pixelation and distortion. No characters, symbols, or punctuation can be reliably extracted. Therefore, no OCR text can be generated that matches the visual content of the source image.
ภาพ B
โหมดกำลัง
650W / Dyson A 1000W / 900W / 700W / 650W
The image contains no legible text or characters. The OCR result "1" is a hallucination and does not correspond to any content in the source image. Therefore, no valid OCR text can be generated that matches the visual content of the source image.
[No text detected]
在东山，曰：长青，云云？在东山
a1 = 0,·s ,bn = 1
7.
การทดสอบคุณภาพ
Hydroxyhydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium hydronium
The following table is a simple formula:
Installation instructions
US
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS MACHINE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND MAINTENANCE MANUAL.
When using an electrical machine, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- Use this machine only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
- Before servicing or cleaning the machine, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
- Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
- When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities.
- Do not use sealant when fixing the machine to the wall.
- Do not install directly above a heating appliance.
- The size of the lead wire used for the wiring connection (including grounding lead) shall not be smaller than 18AWG.
DO NOT USE ANY JETWASH OR POWER WASHING EQUIPMENT FOR CLEANING ON OR NEAR THIS MACHINE.
WARNING
ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN OR DYSON FIELD SERVICE TECHNICIAN IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
CAUTION
Your hand dryer should be located indoors. Operating temperature range 32^ F ( 0^ C) to 104^ F ( 40^ C). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this machine to moisture.
Tools required
Suitable screwdriver for wall type fixings
Small Phillips screwdriver
Small flat head screwdriver
Dyson tool (supplied)
Tape measure and pencil
Hand drill
Suitable drill bit
Pliers/wire strippers
Knife
Pre-installation checks
Pre-installation planning
The machine is designed for a dry, internal location only. Conformity and compliance is the responsibility of the installer. Consult local and national accessibility codes and regulations for relevant installation guidelines. Install the machine in compliance with all building codes and/or regulations. Isolate the power supply before installation or service. Ensure no pipe work (gas, water, air) or electrical cables, wires or ductwork are located directly behind the drilling/mounting area. Select a location that will allow accessibility to the machine and proper clearance from surroundings and floor. Make sure that there are no obstructions between the machine and the floor and at least 8.25in (210mm) above for filter removal. Dyson recommends the use of protective clothing, eye wear and materials when installing/repairing as necessary.
Fig. A
Wall fixing requirements
Do not fix to unsupported plasterboard (drywall) as this will not provide a safe and secure installation for the machine and may also invalidate the warranty.
Where only unsupported plasterboard is available for installation, a Dyson backplate must be used. Contact the Dyson Helpline for further information.
If the wall has an airgap, the fixings used must be of a sufficient length to provide a secure installation.
Do not use sealant when fixing the machine to the wall.
Fig. B
Power modes
This Dyson Airblade™ hand dryer has two power modes, 900W and 650W. The machine is set to 900W as default. If required, change the power mode to 650W before installation.
For more information about the power modes, go to www.dyson.com/airblade
Electrical
Input voltage/Frequency: refer to rating plate.
Make sure that the power supply is switched off before installing.
Cable specification: 3 core cable (live/neutral/earth).
Local electrical regulations must be adhered to when installing or repairing this machine.
Rated power: refer to rating plate.
Operating temperature range: 32°F (0°C) to 104°F (40°C).
Maximum length of strip-back of Live and Neutral wire insulation: 0.25in (7mm).
Quality testing
The Dyson Airblade™ hand dryer has undergone extensive quality testing, to make sure it can withstand forces and impacts typical of a commercial and public bathroom environment.
Installing the Dyson Airblade™ hand dryer
WARNING: Risk of electric shock!
Ensure that the power supply is switched off before continuing.
Fig. 1
Drill the mounting holes
Select the installation location and appropriate height.
Recommended mounting heights are shown on the Mounting template. It may be necessary to adjust the measurements for individual installations.
Fix the supplied Mounting template to the wall in the correct location.
Rear cable entry installation: the electricity supply cable must align from the wall to the entry point on the Mounting template.
Side cable entry installation: an additional hole will need drilling. Refer to the Mounting template for location.
Drill the holes, where marked, using a suitable drill bit.
Fig. 2
For rear cable entry installation
Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the pre-installed earth wire remains in place.
Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don't remove the gland from the backplate.
Using suitable fixings (not countersunk screws), fix the backplate to the wall.
Make sure that the cable sits securely in the cable guide. Any part of the cable not seated securely may prevent the machine from being fixed properly onto the backplate.
Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the pre-installed earth wire remains securely inserted into the connector block.
Unscrew the nut on the earth terminal stud.
Wind the earth cable around the earth terminal stud on the back plate and tighten the nut to secure.
Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
Only clamp double insulated cables with the cable clamp.
Don't overtighten any of the electrical fixtures.
Fig. 3 For side cable entry installation
Using suitable fixings (not countersunk screws), fix the backplate to the wall.
Identify which side the cable will enter. Unscrew the entry tab on the machine.
Cut the rubber side tab of the conduit box on the side that will be facing downwards after installation.
Use a suitable cable gland/conduit connector (not supplied) for the installation.
Secure the conduit box on the wall using suitable fixings.
Unscrew and remove the cable clamp, terminal block and terminal block holder from the backplate. Loosen all three screws on the terminal block, ensuring the pre-installed earth wire remains in place.
Cut the gland smaller than the diameter of the cable and feed the cable through the conduit box and gland. Don't remove the gland from the backplate.
Make sure that the cable sits securely in the cable guide. Any part of the cable not sealed securely may prevent the machine from being fixed properly onto the backplate.
Secure the live, neutral and earth wires to the appropriate terminal block locations, as indicated on the backplate. Ensure the pre-installed earth wire remains securely inserted into the connector block.
Secure the terminal block to the backplate with the terminal block holder and secure the cable clamp.
Only clamp double insulated cables with the cable clamp.
Don't overtighten any of the electrical fixtures.
Fig. 4 Install the main body
This Dyson Airblade™ hand dryer has two power modes, 900W and 650W. The machine is set to 900W as default. If required, change the power mode to 650W before installation.
Hook the machine on to the backplate and gently lower the bottom of the machine until it is flush with the wall. Check that both backplate hooks are securely in position before continuing.
Fix the 2 security screws into the bottom of the machine using the tool supplied.
Fig. 5 Complete the installation
Place the filter unit in the machine and make sure it clicks securely into place. Turn on the mains power supply and test the machine is working as it should by placing hands in sight of the sensors.
Please hand this manual to the owner/facilities manager.
Maintenance
US
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS MACHINE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THE INSTALLATION INSTRUCTIONS AND MAINTENANCE MANUAL.
When using an electrical machine, basic precautions should always be followed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- This Dyson machine is not intended for use by, on, or near young children, invalids or infirm persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction by a responsible person concerning use of the machine to ensure that they can use it safely.
- Do not allow the machine to be used for any purpose other than drying hands. Use this machine only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
- Before servicing or cleaning the machine, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
DO NOT USE ANY JETWASH OR POWER WASHING EQUIPMENT FOR CLEANING ON OR NEAR THIS MACHINE.
WARNING
ALL ELECTRICAL INSTALLATION AND REPAIR WORK SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN OR DYSON FIELD SERVICE TECHNICIAN IN ACCORDANCE WITH CURRENT LOCAL CODES OR REGULATIONS.
CAUTION
Your hand dryer should be located indoors. Operating temperature range 32^ F ( 0^ C) to 104^ F ( 40^ C). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this machine to moisture.
Looking after your hand dryer
Please register as a Dyson hand dryer owner
To help us ensure you receive a prompt and efficient service, please register your machine at www.dyson.com/airblade. This will register your warranty, confirm ownership of your Dyson machine in the event of an insurance loss, and enable us to contact you if necessary.
You will need your serial number, which can be found on the rating plate inside the main body and on the information sticker on the front of the machine.
Please ensure all instructions and guidance in the Installation instructions and Maintenance manual are adhered to or your warranty may be invalidated.
Maintenance
How to use
Place your hands beneath the Dyson Airblade™ hand dryer arms and it will start automatically, creating sheets of air that scrape water from your hands.
For best dry time results:
Keep your hands flat and parallel to the machine's surface, approximately 0.2in (5mm) from the air aperture, drawing your hands through the airflow from your wrists to finger tips.
Move your hands backwards and forwards slowly through the air, turning them over so both back and front are exposed to the airflow.
Keep your hands flat, close the gaps between your fingers and keep your thumbs tucked in, so the whole of your hand is drawn through the airflow.
For more information about the power modes, go to www.dyson.com/airblade
Troubleshooting
Hand dryer cuts out
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Turn the machine off and on again at the mains electricity supply.
Make sure the sensors are clean.
Check the air apertures are clean and free of dust and blockages. If the air apertures are dusty, simply remove dust.
Check that the air inlet is free from blockages.
The dry time has increased
Make sure that the correct power mode has been selected.
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
The airflow is running hotter than usual
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
Air is continuously running
After 30 seconds of continued use the hand dryer will turn off automatically. Remove and replace hands to restart.
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
Contact Dyson for further support and information or online at www.dyson.com/airblade
Cleaning
The hand dryer should be cleaned daily.
Wipe the sensors using a soft cloth and non-abrasive cleaner.
Important information
Do not pressure or power wash the machine.
All cleaning chemicals should be used exactly as indicated by the manufacturer's instructions (including appropriate dilution).
Any chemicals intended for use should first be tested on an inconspicuous area to confirm suitability. Aside from cleaning chemicals, care should be taken to avoid any harmful fluids from coming into contact with the product, in particular oils and alcohol-based products.
Filter maintenance
Regularly check the air inlet to ensure that it is free from dust and debris. Simply wiping the inlet with a soft cloth should be sufficient to remove dust and debris.
If the air inlet gets clogged, further cleaning or a filter change might be required.
If required for high usage environments, a Dyson filter change kit provides everything needed to change your machine's HEPA filter on site. Contact the Dyson Helpline for more information.
Filter cleaning or replacement for your hand dryer can be carried out by carefully following the instructions given in the filter change kit. If in any doubt, consult a qualified electrician or contact the Dyson Helpline for support.
Servicing
If your hand dryer needs servicing, please call the Dyson Helpline or visit the website at www.dyson.com/airblade
Additional information
Disposal information
- Dyson products are made from high grade recyclable materials. Recycle where possible.
Conformity information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Your warranty
Terms and conditions of the Dyson 5 year limited warranty
- If you have registered your machine online, your warranty will start from the date of purchase. Please retain your proof of purchase. If you do not have your proof of purchase, your warranty will start 90 days after the date of manufacture, according to Dyson's records.
- This warranty will be void if the machine is installed and used in a country outside the one in which it was sold.
What is covered
- All factory parts of your hand dryer are warranted against original defects, material and workmanship when used in accordance with the Dyson manual for a period of 5 years from the start of your warranty.
- Where Dyson determines that the main body assembly needs replacing, Dyson will send a replacement to be fitted by the customer on site. The customer will need to return any defective parts to Dyson using the prepaid postage box provided.
- Any replaced parts must be returned to Dyson or an administration fee will be levied.
- Please call the Dyson Helpline for more information.
- Any parts that are returned and replaced by Dyson will become the property of Dyson.
- The replacement of any part of your machine under warranty will not extend the period of warranty.
- This limited warranty provides benefits, which are additional to and do not affect any statutory rights you may have as a consumer. This limited warranty gives you legal rights, and you may have other rights which vary from state to state.
What is not covered
Dyson shall not be liable for costs, damages or repairs incurred as a result of, due to, or from:
• Purchases of machines from unauthorized dealers.
- Careless operation or handling, misuse, abuse and/or lack of maintenance or use not in accordance with the Dyson manual.
- Use of parts not in accordance with the Dyson manual.
- Use of parts and accessories other than those produced or recommended by Dyson.
• External sources such as weather, electrical outages or power sur
- Faulty installation or installation that does not precisely follow the installation instructions supplied by Dyson (except where installed by Dyson).
• Repairs or alterations carried out by unauthorized parties or agents.
• Normal wear and tear (e.g. fuse, etc.).
- Damage caused by cleaning which is not in line with the instructions in the Dyson manual. Do not use chemicals to clean the machine.
- Damage caused by water ingress due to cleaning or treatment prohibited in the Dyson manual.
- Any electrical, flooding or structural damage, or any loss of business or revenue as a result of product failure. If you are in any doubt as to what is covered by your warranty, please contact Dyson.
Warranty limitations and exclusions
• To the fullest extent permitted by applicable law, any implied warranties relating to your machine including but not limited to warranty of merchantability or warranty of fitness for a particular purpose, are limited to the duration of this warranty.
- To the fullest extent permitted by applicable law, your remedy for breach of this warranty is limited to the warranty service described below. Dyson will not be liable for any consequential damages or incidental damages you may incur in connection with your purchase and use of your machine.
- This limited warranty gives you specific legal rights. You may also have other rights which vary by State.
• This limited warranty is not transferable.
- The limitations or exclusions of liability stated herein apply in the state of New Jersey, to the fullest extent permitted by applicable law.
Important data protection information
When registering your Dyson machine:
- You will need to provide us with basic contact information to register your machine and enable us to support your warranty.
- When you register, you will have the opportunity to choose whether you would like to receive communications from us. If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
• We never sell your information to third parties and only use information that you share with us as defined by our privacy policies which are available on our website at privacy.dyson.com
- Installation instructions
- GB/IE
- READ AND SAVE THESE INSTRUCTIONS
- IMPORTANT SAFETY INSTRUCTIONS
- WARNING
- CAUTION
- Tools required
- Pre-installation checks
- Pre-installation planning
- Fig. A
- Wall fixing requirements
- Fig. B
- Power modes
- Electrical
- Quality testing
- Installing the Dyson Airblade™ hand dryer
- Fig. 1
- Drill the mounting holes
- Fig. 2
- For rear cable entry installation
- Fig. 3 For side cable entry installation
- Fig. 4 Install the main body
- Fig. 5 Complete the installation
- Maintenance
- Looking after your hand dryer
- Please register as a Dyson hand dryer owner
- How to use
- Troubleshooting
- Hand dryer cuts out
- Dry time has increased
- Airflow is running hotter than usual
- Air is continuously running
- Cleaning
- Important information
- Filter maintenance
- Servicing
- Additional information
- Disposal information
- Your guarantee
- What is covered
- What is not covered
- Summary of cover
- Important data protection information
- AU/NZ
- The dry time has increased
- The airflow is running hotter than usual
- CA
- Your warranty
- Warranty limitations and exclusions
- 维护
- CN
- 阅读并保存这些说明 重要安全说明
- 維護
- TW/HK
- ! VIDVÖRUN
- 추가 정보
- 폐기 정보
- Figur 5
- DÔLEŽITÉ BEZPEČNOSTNÉ POKYNY
- ภาพ B
- โหมดกำลัง
- การทดสอบคุณภาพ
- US
- Conformity information
Brand : DYSON
Model : Airblade 9kJ
Category : Hand dryers