HDS 820 De - Pressure washer Kärcher - Free user manual and instructions

USER MANUAL HDS 820 De Kärcher

Technical line drawing of a portable gas generator with visible internal components and wheels (no text or labels)

Technical line drawing of a portable gas purifier with visible internal components and wheels (no text or labels)

Deutsch 6

English 16

Français 26

Italiano 36

Nederlands 46

Español 56

Português 66

Dansk 76

Norsk 85

Svenska 94

Suomi 103

Ελληνικά 112

Türkçe 122

Русский 131

Magyar 142

Čeština 152

Slovenščina 161

Polski 170

Românește 180

Slovenčina 190

Hrvatski 200

Srpski 209

Български 218

Eesti 229

Latviešu 238

Lietuviškai 247

Українська 257

العربية 267

Illustration of an open book with a black arrow indicating rotation (no text or symbols)

A

Technical diagram of a portable water purifier with numbered components and labeled parts

Technical diagram of a portable gas pump with numbered components and an inset close-up view of internal components.

B

Technical diagram of a Karcher Gasoline pump system with numbered components and labeled parts

C 35 45 60 70 80

D OIL ALARM LAMP OFF ON HEATER START START SWITCH 1 2

Technical line drawing of a mechanical assembly with labeled component (1), no readable text or symbols beyond label

F ① ②

G 1 2 3 4 5

H 2 3 1 4

Technical diagram of a mechanical device with numbered components labeled 1, 2, and 3.

Inhalt

Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Technische Daten

Environmental protection.... 16

Accessories and spare parts 16

Safety instructions 17

Symbols on the device 17

Safety devices.... 17

Device description.... 18

Initial startup 19

Operation.... 20

Transport 21

Storage.... 22

Care and service 22

Troubleshooting guide.... 23

Warranty 24

Declaration of Conformity.... 24

Technical data 25

General notes

Read the original instructions before using the device for the first time and act in accordance with it. Keep the original in-

structions for future reference or for future owners.

• If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.
• Notify the dealer immediately in the case of shipping damage.
• Check the package contents when unpacking for missing accessories or for damage.

Intended use

Note

Applies to Germany only: The device is only intended for mobile (not stationary) operation.

• This high-pressure cleaner is used especially where no electrical connection is available and hot water is to be used.
• The device is only intended for cleaning, e.g. machines, vehicles, buildings, tools, facades, terraces and garden machines.
• We recommend using the dirt grinder as a special accessory for stubborn dirt.

⚠️DANGER

Use at petrol stations or other hazard zones

Risk of injury

Adhere to the respective safety regulations.

Note

Do not allow waste water containing mineral oil to enter the ground, water or sewage system. Carry out motor washing or undercarriage wash only at suitable places with an oil separator.

Water supply limit values

ATTENTION

Dirty water

Premature wear and tear or deposits in the device Supply the device using only clean water, or recycled water that does not exceed the specified limit values.

The following limit values apply to the water supply:

• pH value: 6.5-9.5

• Electrical conductivity: Conductivity of fresh water + 1200 μS/cm, maximum conductivity 2000 μS/cm

• Settleable particles (sample volume 1 l, settling time 30 minutes): < 0.5 mg/l

• Filterable particles: < 50 mg/l, no abrasive substances
  • Hydrocarbons: < 20 mg/l
• Chloride: < 300 mg/l
• Sulphate: < 240 mg/l
  • Calcium: < 200 mg/l
• Total hardness: < 28 °dH, < 50° TH, < 500 ppm (mg CaCO₃/l)
• Iron: < 0.5 mg/l
  • Manganese: < 0.05 mg/l
• Copper: < 2 mg/l
  • Active chloride: < 0.3 mg/l
  • Free of unpleasant odours

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Cleaning work producing in oily waste water, e.g. washing engines, washing undercarriages etc., may only be performed at washing stations with an oil separator.

Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil.

Extraction of water from public waterways is not permitted in some countries.

Please do not allow engine oil, heating oil, diesel and petrol to enter the environment.

Please protect the ground and dispose of old oil in an environmentally friendly manner.

Notes on the content materials (REACH)

Current information on content materials can be found at: www.kaercher.de/REACH

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

Safety instructions

⚠️DANGER

• Do not operate the device if fuel has been spilled. In such a case, move the device to another location and avoid any sparking.
• Do not store fuel in the proximity of naked flames or devices such as ovens, heating boilers, water heaters, etc. that have a pilot light or may generate sparks. Do not use or spill fuel in the above environment.
• Keep easily flammable objects at least 2 m away from the muffler.
• Do not operate the device without a muffler. Check the muffler regularly and clean or replace it if necessary.
• Do not operate the device in forests, bushy or grassy areas if the exhaust pipe is not equipped with a spark catcher.
• Do not run the motor with the air filter removed or without a cover over the intake opening.
• Do not adjust any control springs, governor control linkage or other parts that could increase the speed of the motor.
• Do not touch any hot parts such as the muffler, cylinder or cooling fins.
• Never bring your hands and feet close to rotating parts.
• Never operate the device in confined spaces.
• Do not use unsuitable fuels as they can be dangerous.

General safety instructions

• Observe the respectively applicable national regulations for liquid jet cleaners.
• Observe the respectively applicable national accident prevention regulations. Liquid jet cleaners must be tested regularly and the results of the test recorded in writing.
• Note that the heating system in the device is classified as a furnace. Furnaces must be inspected regularly according to the applicable national regulations.
• No modifications may be made to the device or accessories.

Symbols on the device

Do not aim the high-pressure jet may at persons, animals, live electrical equipment or the device itself.

Protect the device against frost.

According to applicable regulations, the device must never be used with the drinking water network without a system separator. Ensure that the connection to your house water system, with which the high-pressure cleaner is operated, is equipped with a system separator according to EN 12729 type BA. Water that has flowed through a system separator is classified as undrinkable. Always connect the system separator to the water inlet and never directly to the device.

Danger of injury from electrical voltage. Only qualified electricians or authorised and qualified technical specialists are permitted to work on the electrical systems.

Risk of burns from hot surfaces.

Health risk from poisonous exhaust gases. Never inhale the exhaust gases.

Safety devices

⚠CAUTION

Missing or modified safety devices

Safety devices are provided for your own protection. Never modify or bypass safety devices.

Water shortage safeguard

The water shortage safeguard prevents the burner from overheating in the case of water shortage. The burner only starts up if there is sufficient water supply.

Pressure relief valve

If the high-pressure gun is closed, the overflow valve opens and the high-pressure pump pumps the water back to the pump suction side. That prevents the maximum permissible working pressure from being exceeded.

The overflow valve is set and sealed at the factory. The adjustment is made by Customer Service.

Safety valve

The safety valve opens if the pressure relief valve is faulty.

The safety valve is set and sealed at the factory. The adjustment is made by Customer Service.

Thermostat valve on the pump

The thermostat valve opens when the maximum permissible water temperature is exceeded and discharges the hot water outdoors.

Pressure switch

The pressure switch switches the burner off when the minimum working pressure is fallen short of and on again when it is exceeded.

Emission temperature limiter

The emission temperature limiter switches the device off when the emission temperature is too high.

Safety latch

The safety catch on the high-pressure gun prevents the device from being switched on inadvertently.

Device description

Overview of HDS 8/20 De

See graphics page for illustration Illustration A

① Protector

② High-pressure nozzle

③EASY!Lock spray lance

④ EASY!Force high-pressure gun

⑤ Safety latch

⑥Trigger

⑦ Unlocking lever

⑧ EASY!Lock high-pressure hose

⑨ Ignition electrode

⑩ Burner sight glass

⑪ Temperature controller

⑫ Booster heater

⑬ Fuel filter

⑭ Battery for electric start

⑮ Parking brake

16 Electrical box

⑰ High-pressure gun storage compartment

⑱ Exhaust manifold

⑲Storage hook for high-pressure hose

⑳ Shut-off lever

21 Motor oil drain screw

22 Water inlet

23 Water filter

⑳Water outlet / high-pressure connection EASY! Lock

25 Retaining clip

⑳Hose piece

27 Sieve in the safety block

28 Pressure relief valve

29 Flow monitor

③0 High-pressure pump oil level indicator

③1 Fuel tank cap with filter

③2 Fuel tank

③3 Fuel pre-filter

③4 Level switch

③5 Top cover

③6 Type plate

37 Motor switch

③8 Motor oil indicator light

⑲Manual start device

④0 Air filter

Overview of HDS 8/20 G

See graphics page for illustration Illustration B

① Protector

② High-pressure nozzle

③ EASY!Lock spray lance

④ EASY!Force high-pressure gun

⑤ Safety latch

6 Trigger

⑦ Unlocking lever

⑧ EASY!Lock high-pressure hose

⑨ Ignition electrode

⑩Burner sight glass

⑪ Temperature controller

⑫ Booster heater

⑬ Fuel filter

⑭Parking brake

⑮High-pressure gun storage compartment

16 Electrical box

⑰ Storage hook for high-pressure hose

18 Air filter

⑲Water inlet

20 Motor oil drain screw

21 Water filter

22 Water outlet / high-pressure connection EASY! Lock

23 Retaining clip

24 Hose piece

25 Sieve in the safety block

26 Pressure relief valve

27 Flow monitor

28 High-pressure pump oil level indicator

29 Fuel tank cap with filter

30 Fuel tank

31 Fuel pre-filter

32Level switch

33 Top cover

③4Type plate

35 Motor switch

36 Manual start device

37 Fuel cock

38 Choke

HDS 8/20 De control elements

• Temperature controller Illustration C
- Motor electrical starter Illustration D

① Motor oil indicator light

② Motor switch

HDS 8/20 G control elements

• Temperature controller Illustration C
- Motor switch Illustration E

① Motor switch

- Choke / fuel cock Illustration F

① Choke

② Fuel cock

Initial startup

⚠ WARNING

Damaged components

Risk of injury

Check that the device, accessories, supply lines and connections are in perfect condition. If the condition is not perfect, you may not use the device.

Check the oil level in the high-pressure pump

ATTENTION

Milky oil

Device damage

If the oil is milky, inform authorized Customer Service immediately.

1. Place the device on a flat and level surface.
2. Check the high-pressure pump oil level at the oil level display. The oil level must be in the middle of the oil level in dication.
3. Top up the oil if necessary.

Starting up the motor

1. Before initial startup of the motor, read the original instructions for the motor and observe the safety instructions.

Check the motor oil level

1. Check the oil level in the motor. Do not start up the device if the oil level is below the "MIN" mark.
2. Top up the oil if necessary.

Topping up with fuel - HDS 8/20 De

ATTENTION

Unsuitable fuel

Risk of explosion

Only fill the fuel tank with diesel oil or light heating oil. Operation with biodiesel according to EN 14214 (above an exterior temperature of 6 °C) is possible.

Do not use unsuitable fuels, e.g. petrol.

ATTENTION

Operation with an empty fuel tank

Destruction of the fuel pump

Never operate the device with an empty fuel tank.

1. Open the fuel tank cap.
2. Fill the fuel tank with fuel.
3. Close the cap of the fuel tank.
4. Wipe up any spilled fuel.

Topping up fuel - HDS 8/20 G

⚠️DANGER

Unsuitable fuel

Risk of explosion

Only fill with petrol. Unleaded petrol (86 RON) can be used.

1. Open the fuel tank cap.
2. Fill the fuel tank with fuel.
3. Close the cap of the fuel tank.
4. Wipe up any spilled fuel.

Pouring in fuel

⚠️DANGER

Unsuitable fuel

Risk of explosion

Only use diesel fuel or light heating oil. Unsuitable fuels, such as petrol, must not be used.

ATTENTION

Operation with an empty fuel tank

Destruction of the fuel pump

Never operate the device with an empty fuel tank.

1. Open the fuel tank cap.
2. Fill the fuel tank with fuel.
3. Close the cap of the fuel tank.
4. Wipe up any spilled fuel.

Install the spray lance, high-pressure gun, high-pressure hose and high-pressure nozzle

Note

The EASY!Lock system connects components quickly and safely via a single turn of the quick-release thread.

1. Connect the spray lance to the high-pressure gun and hand-tighten the screw connection.
2. Connect the high-pressure hose to the high-pressure gun.
3. Fit the high-pressure nozzle.

a Plug the high-pressure nozzle onto the spray lance.
b Mount the protective part and tighten it hand-tight.

1. Mount the high-pressure hose at the high-pressure connection of the device.

Water connection

Connection to a water line

For the connected loads and the requirements for the water supply hose, see chapter Technical data.

Note

The water supply hose is not included in the scope of delivery.

1. Connect the water supply hose to the water inlet of the device.
2. Connect the water supply hose to the water inlet (e.g. tap).
3. Open the water inlet.

Suck water from the container

This high-pressure cleaner is equipped with appropriate accessories for the suction of surface water e.g. from water butts or ponds.

⚠️DANGER

Suction of fluids containing solvents or drinking water

Risk of injury and damage, contamination of drinking water

Never extract fluids containing solvents such as paint thinner, petrol, oil or unfiltered water. The seals in the device are not resistant to solvents. The spray mist of solvents is highly flammable, explosive and poisonous. Never extract water from drinking water tanks.

1. Connect the suction hose (diameter at least 3/4") with filter (accessory) to the water inlet.

2. Hang the suction hose in an external water source (max. suction height see chapter Technical data).

Operation

⚠️DANGER

Flammable fluids

Risk of explosion

Do not spray inflammable liquids.

⚠️DANGER

Operation without spray lance

Risk of injury

Never operate the device without the spray lance installed.

Before each use, check that the spray lance is firmly seated. The screw connection of the spray lance must be tightened hand tight.

⚠️DANGER

High-pressure water jet

Danger of injury

Never fasten the trigger and safety lever in the actuated position.

Do not use the high-pressure gun when the safety lever is damaged.

Push the safety latch of the high-pressure gun forwards every time before starting work with the device.

Hold the high-pressure gun and spray lance with both hands.

ATTENTION

Rolled up high-pressure hose

Risk of damage

Unroll the high-pressure hose completely before starting operation.

Opening/closing the high-pressure gun

1. Actuate the safety lever and trigger. The high-pressure gun opens.

2. Release the safety lever and trigger. The high-pressure gun closes.

Changing the high-pressure nozzle

⚠️DANGER

Residual high pressure in the device

Danger of injury

Switch off the device prior to changing nozzles.

Actuate the high-pressure gun until the device is completely depressurised.

1. Push the safety latch forwards. The high-pressure gun is secured.

2. Change the high-pressure nozzle.

Switching on the device

Note

You can remove the high-pressure nozzle from the spray lance to make starting easier.

1. Open the water inlet.

2. Set the temperature controller to operation with cold or hot water.

3. Push the safety latch backwards. The high-pressure gun is unlocked.

4. Open the high-pressure gun.

5. Start the motor with the high-pressure gun open according to the original motor instructions.

If cleaning does not start immediately, secure the high-pressure gun (see chapter Interrupting operation).

Cleaning

1. Adjust the pressure and temperature according to the surface to be cleaned.

Cold water operation

1. Set the temperature controller to the "Burner off" position.

Operation with hot water

⚠️DANGER

Hot water

Risk of scalding

Avoid contact with hot water.

1. Set the temperature controller to the desired working temperature.

The burner is switched on.

Operation with detergent

Note

A cup foam lance (optional) is needed for operating with detergent.

⚠ WARNING

Incorrect handling of detergents

Health risk

Adhere to the safety instructions stated on the detergent packaging.

ATTENTION

Unsuitable detergents

Damage to the device and the objects to be cleaned Use only detergents approved by KÄRCHER.

Observe the dosing recommendations and notes provided with the detergent.

Use detergents sparingly to help conserve the environment.

ATTENTION

Water temperatures too high

Damage to the cup foam lance

The cup foam lances are only suitable for water temperatures up to 60 °C. For operation with detergent, do not select water temperatures above 60 °C.

KÄRCHER detergents ensure fault-free operation. Ask us for a consultation, request our catalogue or our detergent information sheets.

Cup foam lance 4.112-054.0

Illustration G

① Container

② Foam nozzle

③ EASY!Force high-pressure gun

④ Suction hose

⑤ Gate Detergent mixing: 3=high, 2=medium, 1=low

1. Unscrew the container.

2. Plug the desired gate into the suction hose.

3. Fill the detergent into the container.

4. Screw the container on to the foam lance.

5. Remove the spray lance from the high-pressure gun.

6. Attach the foam lance to the high-pressure gun and hand-tighten it.

7. Start up the high-pressure cleaner.

Cup foam lance 2.112-018.0

Illustration H

① Container

② Spray form twist grip

③ Detergent dosing rotary knob

④EASY!Force high-pressure gun

1. Unscrew the container.

2. Fill the detergent into the container.

3. Screw the container on to the foam lance.

4. Remove the spray lance from the high-pressure gun.

5. Attach the foam lance to the high-pressure gun and hand-tighten it.

6. Start up the high-pressure cleaner.

7. Adjust the detergent dosing unit using the detergent dosing rotary knob.

8. Adjust the jet width using the spray form twist grip.

Recommended cleaning method

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).

2. Rinse off the loosened dirt with the high-pressure jet.

Rinsing the cup foam lance

The foam lance must be rinsed after use to prevent the development of detergent deposits.

1. Unscrew the container.

2. Pour the remaining detergent back into the original packaging.

3. Fill the container with clear water.

4. Screw the container onto the foam nozzle.

5. Operate the foam nozzle for approx. 1 minute to flush the detergent residue.

6. Empty the container.

Interrupting operation

1. Close the high-pressure gun.

2. Push the safety latch forwards.

The high-pressure gun is secured.

Note

If the high-pressure gun is closed, the motor continues to run at idle speed. The water then circulates within the pump and heats up. When the cylinder head at the pump has reached the maximum permissible temperature (80 °C), the thermostat valve on the pump opens and lets out the hot water into the open. Cooling can be accelerated when operating with pressurized water from the water pipe network:

1. Open the high-pressure gun for about 2-3 minutes. The water flowing through it cools the cylinder head.

Ending operation

⚠️DANGER

Hot water

Risk of scalding

After operation with hot water, operate the device for at least 2 minutes with cold water with the high-pressure gun open for cooling down.

ATTENTION

Stopping the motor at full load

Risk of damage

Never switch off the motor at full load with the high-pressure gun open.

Note

After operation with salty water (seawater) rinse the device with tap water and an open high-pressure gun for at least 2-3 minutes.

1. Set the temperature controller to the "Burner off" position.

2. Rinse the device for at least 30 seconds.

3. Close the high-pressure gun.

The motor is running at idle speed.

1. Turn the motor switch to the "OFF" position.

2. Close the fuel cock.

3. Close the water inlet.

4. Actuate the high-pressure gun until the device is completely depressurised.

5. Push the safety latch forwards.

The high-pressure gun is secured.

1. Unscrew the water supply hose from the device.

Transport

△CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during transportation.

ATTENTION

Improper transportation

Risk of damage

Protect the trigger of the high-pressure gun from damage.

1. Release the parking brake.

2. Push the device.

3. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respective, valid guidelines.

Storage

△CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during storage.

Frost protection

ATTENTION

Frost

Destruction of the device through freezing water

Drain all water from the device.

Store the device in a frost-free location.

If frost-free storage is not possible:

1. Drain the water.

2. Pump commonly available anti-freeze through the device.

Care and service

⚠️DANGER

Danger due to device inadvertently starting up

Risk of injury

Disconnect the fuel supply prior to all work on the device.

△CAUTION

Hot surfaces

Risk of injury

Allow the device to cool down prior to all work.

Note

Observe the information on care and service in the original instructions for the motor.

Safety inspection/maintenance contract

You can agree on regular safety inspections or close a maintenance contract with your dealer. Please seek advice on this.

Maintenance intervals

Before every use

ATTENTION

Milky oil

Device damage

If the oil is milky, inform authorized Customer Service immediately.

1. Check the oil level of the high-pressure pump (see chapter Check the oil level in the high-pressure pump).

Weekly

1. Clean the water filter (see chapter Cleaning the water filter).

2. Check the fuel filter and replace it if necessary.

Half-yearly

1. Check the booster heater (see chapter Checking the booster heater).

2. Clean the sieve in the safety block (see chapter Cleaning the sieve in the safety block).

3. Unscrew the high-pressure hose from the water outlet. If there is a clear, white layer of lime in the water outlet, descale the device. If there is a thick layer of lime, descale frequently.

Every six months or as required

1. Drain the fuel tank.

2. Clean the fuel tank.

3. Clean the fuel filter.

4. Clean the fuel nozzle.

5. Clean the heating coil.

a Desulphurise the heating coil. b Remove soot from the heating coil.

1. Change the oil in the high-pressure pump.

Every 500 operating hours, at least annually

● Have the device serviced by the authorized Customer Service.

Maintenance work

Cleaning the water filter

1. Shut off the water inlet.

2. Unscrew the filter cup.

Illustration I

① Water filter

② Filter insert

③ Filter chamber

1. Pull the filter insert downwards and off.

2. Clean the filter insert and filter cup.

3. Re-install the filter insert.

4. Screw on the filter cup again and tighten.

Checking the booster heater

1. Disassemble the burner insert.

2. Clean the burner.

3. Clean the ignition electrodes or replace them, if necessary.

4. Check the electrode gap. Adjust the electrode gap if necessary.

Cleaning the sieve in the safety block

1. Open the high-pressure gun until the device is completely depressurised.

2. Pull out the securing clip.

3. Pull the hose section out of the safety block.

4. Pull the sieve out of the safety block.

5. Clean the sieve under running water.

6. Mount the components in the reverse order.

Replacing the oil in the high-pressure pump

For the oil type and filling quantity see chapter Technical data.

1. Provide a catch pan for at least 1 litre of oil.

2. Unscrew the oil drain plug.

3. Drain the oil into the catch pan.

4. Screw in the oil drain plug.

5. Slowly fill with new oil until the middle of the oil level indication is reached. Air bubbles must be able to escape.

Descaling the device

If deposits accumulate in the pipelines, this will increase the flow resistance and the motor load will get too high.

⚠️DANGER

Flammable gases

Risk of explosion

Do not smoke during the descaling process.

Ensure good ventilation.

⚠️DANGER

Acids

Risk of acid burns

Wear safety goggles and protective gloves.

According to legal regulations, only approved scaling solvents with test symbol may be used for descaling.

• RM 101 (order number 6.295-398.0)

1. Fill a container for 20 litres with 15 litres of water.
2. Add 1 litre of scale remover.
3. Connect the water hose to the water connection and hang the free end in the container.
4. Insert the connected spray lance without the high-pressure nozzle in the container.
5. Start the motor according to the original instructions for the motor.
6. Open the high-pressure gun and do not close it again during descaling.
7. Set the temperature controller to a working temperature of 40 °C .
8. Let the device run until the working temperature is reached and the burner goes out.
9. Switch off the device and allow it to stand for 20 minutes. The high-pressure gun must remain open.
10. Pump the device empty.

Note

We then recommend pumping an alkaline solution (e.g. RM 81) through the device to protect against corrosion and neutralize the acid residues.

Vent the device

1. Open the water inlet.
2. Remove the high-pressure nozzle.
3. Start the motor according to the original instructions for the motor.
4. Allow the device to run until the escaping water is free of air bubbles.
5. Switch off the device.
6. Fit the high-pressure nozzle.

Troubleshooting guide

⚠️DANGER

Danger due to device inadvertently starting up

Risk of injury

Disconnect the fuel supply prior to all work on the device.

△CAUTION

Hot surfaces

Risk of injury

Allow the device to cool down prior to all work.

Motor not running

1. See original instructions for the motor.
   The fuel tank is empty
2. Fill the fuel tank.
   The oil level in the motor is too low
3. Check the oil level in the motor.
4. Refill oil.

Device not building up pressure

A wrong high-pressure nozzle is mounted on the spray lance.

1. Fit the standard nozzle (see chapter Technical data).
   The high-pressure nozzle is clogged / washed out
2. Clean / replace the high-pressure nozzle.
   Air is in the system
3. Vent the device (see chapter Vent the device).

The water filter is clogged

1. Clean the water filter (see chapter Cleaning the water filter).

The sieve in the safety block is clogged

1. Clean the sieve in the safety block (see chapter Cleaning the sieve in the safety block).

The water supply volume is too low

1. Check the water supply volume (see chapter Technical data).

The safety valve is adjusted

1. Have the safety valve adjusted by the authorized Customer Service.

The safety valve is leaking

1. Have the safety valve or seal replaced by the authorized Customer Service.

The overflow valve is defective

1. Have the overflow valve replaced by the authorized Customer Service.

Uneven water jet

The high-pressure nozzle is clogged

1. Clean the high-pressure nozzle.

The safety valve is adjusted

1. Have the safety valve adjusted by the authorized Customer Service.

Oil in the high-pressure pump milky

The seal is defective

1. Contact the authorized Customer Service.

The burner does not ignite

The temperature limiter has triggered repeatedly

1. Have the device checked by the authorized Customer Service.

The fuel tank is empty

1. Fill the fuel tank.

The water volume is too low

1. Check the water connection.

2. Check the supply lines.

3. Clean the sieve in the safety block (see chapter Cleaning the sieve in the safety block).

The fuel pump is defective

1. Have the fuel pump replaced by the authorized Customer Service.

The fuel filter is clogged

1. Replace the fuel filter.

There is no ignition spark

1. If no ignition spark is visible through the burner sight glass during operation, have the device checked by the authorized Customer Service.

Fuel atomization at the burner nozzle is uneven

1. Replace the fuel filter.

The level switch in the fuel tank has switched off the device

1. Top up the fuel tank.

Water shortage safeguard does not switch on - no flame

The water inlet is closed
1. Open the water inlet.
The water supply volume is too low
1. Increase the water supply volume.
The sieve in the safety block is clogged
1. Clean the sieve in the safety block (see chapter Cleaning the sieve in the safety block).
The valves in the high-pressure pump piping are leaking or contaminated
1. Contact the authorized Customer Service.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)

Declaration of Conformity

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

Product: High-pressure cleaner

Type: 1.210-xxx

Currently applicable EU Directives

2000/14/EC

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Harmonised standards used

EN IEC 63000: 2018

EN 55012: 2007 + A1: 2009

EN 60335-1

EN 60335-2-79

EN 61000-6-1: 2007

Conformity evaluation procedure used

2000/14/EC: Annex V

Sound power level dB(A)

HDS 8/20 De

Measured: 114

Guaranteed: 116

HDS 8/20 G

Measured: 107

Guaranteed: 109

National standards used

The signatories act on behalf of and with the authority of the company management.

H. Jenner

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Declaration of Conformity (UK)

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

Product: High-pressure cleaner

Type: 1.210-xxx

Currently applicable UK Regulations

S.I. 2001/1701 (as amended)

S.I. 2008/1597 (as amended)

S.I. 2012/3032 (as amended)

S.I. 2016/1091 (as amended)

Designated standards used

EN IEC 63000: 2018

EN 55012: 2007 + A1: 2009

EN 60335-1

EN 60335-2-79

EN 61000-6-1: 2007

Conformity assessment procedure used

S.I. 2001/1701 (as amended): Schedule 8

Sound power level dB(A)

HDS 8/20 De

Measured: 114

Guaranteed: 116

HDS 8/20 G

Measured: 107

Guaranteed: 109

National standards used

The signatories act on behalf of and with the authority of the company management.

H. Jenner

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Technical data

		HDS 8/20 De HDS 8/20 G
Internal combustion engine
Engine type LC186F(D) G300FA
Power kW/PS 6,8 / 9,2 6,8 / 9,2
Specific consumption l/h 2,2 3,2
Engine speed 1/min 3350-3450 3300-3400
Water connection
Feed pressure (max.) MPa (bar) 0,6 (6)	0,6 (6)
Input temperature (max.)	°C	30	30
Input amount (min.)	l/h (l/min)	1000 (16,7)	1000 (16,7)
Suction height (max.) m 0,5 0,5
Minimum water supply hose length	m	7,5 7,5
Minimum water supply hose diameter	in	3/4 3/4
Device performance data
Degree of protection		IPX5	IPX5
Nozzle size of standard nozzle		045	045
Water flow rate	l/h (l/min)	800 (13,3)	800 (13,3)
Water operating pressure with standard nozzle	MPa (bar)	20 (200)	20 (200)
Excess operating pressure safety valve (maximum)	MPa (bar)	25 (250)	25 (250)
Hot water operating temperature (maximum) °C	80	80
Burner output	kW	64	64
Fuel consumption (max.)	kg/h (l/h)	5,9 (7,0)	5,9 (7,0)
High-pressure gun recoil force	N	45	45
Operating materials
Fuel type		Diesel	Petrol
Motor oil type		SAE 10 W30, SAE 15 W40	SAE 10 W30
Engine oil volume	l	1,2 0,8
Fuel		EL heating oil or die-sel	EL heating oil or die-sel
Pump oil type		15W40	15W40
Pump oil volume	l	0,4 0,4
Dimensions and weights
Weight (without accessories)	kg 234	190
Length x width x height	mm	1130 x 910 x 895	1130 x 910 x 895
Fuel tank capacity	l	4,5 6,0
Fuel tank capacity	l	30	30
Determined values in acc. with EN 60335-2-79
High-pressure gun hand-arm vibration value	m/s^2	2,7 2,7
Spray lance hand-arm vibration value	m/s^2	<2,5	<2,5
Uncertainty K	m/s^2	1	1
Sound pressure level L_pA	dB(A)	99	92
Uncertainty K_pA	dB(A)	3	3
Sound power level L_WA + K uncertainty _WA	dB(A)	116	109
CO2Emissions according to the measurement procedure of EU regulation 2016/1628 Euro V
Motor	g/kWh	977,78	817,85

Subject to technical modifications.

Contenu

Transport non-conforme

Risque d'endommagement

2006/42/CE (+2009/127/CE)

2011/65/EU

2014/30/UE

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Winnenden, 2020/10/01

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Dati tecnici

De overstroomklep is defect

De afdichting is defect

De brandstofpomp is defect

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Technische gegevens

- Dureza total: < 28 °dH, < 50° TH, < 500 ppm (mg CaCO₃/l)

- Hierro: < 0,5 mg/l - Manganeso: < 0,05 mg/l

• Cobre: < 2 mg/l

2006/42/CE (+2009/127/CE)

2011/65/UE

2014/30/UE

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Datos técnicos

2006/42/CE (+2009/127/CE)

2011/65/UE

2014/30/UE

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Winnenden, 2020/10/01

Dados técnicos

2006/42/EF (+2009/127/EF)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tlf.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Tekniske data

2006/42/EF (+2009/127/EF)

2011/65/EU

2014/30/EU

Anvendte harmoniserte standarder

EN IEC 63000: 2018

EN 55012: 2007 + A1: 2009

EN 60335-1

EN 60335-2-79

EN 61000-6-1: 2007

2000/14/EF: Vedlegg V

Lydeffektnivå dB(A)

HDS 8/20 De

Målt: 114

Garantert: 116

HDS 8/20 G

Mält: 107

Garantert: 109

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tlf.: [phone]

Winnenden, 2020/10/01

Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

D-71364 Winnenden (Germany)

Tfn: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Tekniska data

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Puh.: [phone]

Winnenden, 2020/10/01

Tekniset tiedot

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tηλ.: [phone]

Φαξ: [phone]

Winnenden, 2020/10/01

2006/42/AT (+2009/127/AT)

2011/65/AT

2014/30/AB

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

Winnenden, 2020/10/01

Teknik bilgiler

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Тел.: [phone]

Факс: [phone]

Winnenden, 2020/10/01

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Winnenden, 2020/10/01

Műszaki adatok

2006/42/ES (+2009/127/ES)

2011/65/EU

2014/30/EU

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

Winnenden, 2020/10/01

Technické údaje

⑪ Regulator temperature

⑫Pretočni grelnik

⑬ Filter goriva

⑭Parkirna zavora

⑮ Odlagalna površina za visokotlačno pištolo

• Regulator temperature Slika C

• Regulator temperature Slika C

2006/42/ES (+2009/127/ES)

2011/65/EU

2014/30/EU

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

Winnenden, 2020/10/01

Tehnični podatki

		HDS 8/20 De HDS 8/20 G
Motor z notranjim zgorevanjem
Tip motorja LC186F (D) G300FA
Zmogljivost/moč kW/PS 6,8 / 9,2 6,8 / 9,2
Specifična poraba l/h 2,2 3,2
Število vrtljajev motorja 1/min 3350-3450 3300-3400
Priključek za vodo
Tlak na dotoku (maks.)	MPa (bar)	0,6 (6)	0,6 (6)
Temperatura na dotoku (maks.)	°C	30	30
Količina dotoka (min.)	l/h (l/min)	1000 (16,7)	1000 (16,7)
Višina sesanja (maks.)	m	0,5 0,5
Minimalna dolžina cevi za dovajanje vode	m	7,5 7,5
Minimalni premer cevi za dovajanje vode	in	3/4 3/4
Podatki o zmogljivosti naprave
Stopnja zaščite		IPX5	IPX5
Velikost standardne šobe		045	045
Črpalna količina, voda	l/h (l/min)	800 (13,3)	800 (13,3)
Delovni tlak vode s standardno šobo	MPa (bar)	20 (200)	20 (200)
Dovoljeni delovni nadtlak (maks.) (varnostni ventil)	MPa (bar)	25 (250)	25 (250)
Delovna temperatura tople vode (maks.)	°C	80	80
Moč gorilnika	kW	64	64
Poraba goriva (maks)	kg/h (l/h)	5,9 (7,0)	5,9 (7,0)
Sila vzvratnega sunka visokotlačne pištole	N	45	45
Pogonska sredstva
Vrsta goriva		Dizelsko gorivo bencin,
Vrsta motornega olja		SAE 10 W30, SAE 15 W40	SAE 10 W30
Količina motornega olja	I	1,2	0,8
Gorivo		Grelno olje EL ali dizel	Grelno olje EL ali dizel
Vrsta olja črpalke		15W40	15W40
Količina olja črpalke	I	0,4	0,4
Mere in mase
Teža (brez pribora)	kg 234	190
Dolžina x širina x višina	mm	1130 x 910 x 895	1130 x 910 x 895
Prostornina rezervoarja za gorivo	I	4,5 6,0
Vsebina posode za gorivo	I	30	30
Ugotovljene vrednosti v skladu s standardom EN 60335-2-79
Vrednost tresljajev za dlani/roke - visokotlačna pištola	m/s^2	2,7 2,7
Vrednost tresljajev za dlani/roke - brizgalna cev	m/s^2	<2,5	<2,5
Negotovost K	m/s^2	1	1
Raven tlaka hrupa L_pA	dB(A)	99	92
Negotovost K_pA	dB(A)	3	3
Raven moči hrupa L_WA + negotovost K_WA	dB(A)	116	109
CO2emisije po merilnem postopku Uredbe EU 2016/1628 Euro V
Motor	g/kWh	977,78	817,85

2006/42/WE (+2009/127/WE)

2011/65/UE

2014/30/UE

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Winnenden, 2020/10/01

Dane techniczne

Directive UE relevante

2000/14/UE

2006/42/UE (+2009/127/UE)

2011/65/UE

2014/30/UE

Norme armonizate aplicate

EN IEC 63000: 2018

EN 55012: 2007 + A1: 2009

EN 60335-1

EN 60335-2-79

EN 61000-6-1: 2007

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germania)

Tel.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Date tehnice

2006/42/ES (+2009/127/ES)

2011/65/EÚ

2014/30/EÚ

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2020/10/01

Technické údaje

2006/42/EZ (+2009/127/EZ)

2011/65/EU

2014/30/EU

Primijenjene uskladene norme

EN IEC 63000: 2018

EN 55012: 2007 + A1: 2009

EN 60335-1

EN 60335-2-79

EN 61000-6-1: 2007

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

Opunomoćenik za dokumentaciju:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Njemačka)

Tel.: [phone]

Telefaks: [phone]

Winnenden, 2020/10/01

Tehnički podaci

		HDS 8/20 De HDS 8/20 G
Motor s unutrašnjim izgaranjem
Tip motora LC186F(D) G300FA
Snaga kW/PS 6,8 / 9,2 6,8 / 9,2
Specifična potrošnja l/h 2,2 3,2
Broj okretaja motora 1/min 3350-3450 3300-3400
Priključak za vodu
Dovodni tlak (maks.) MPa (bar) 0,6 (6)	0,6 (6)
Temperatura dovodne vode (maks.)	°C	30	30
Količina dovodne vode (min.)	l/h (l/min)	1000 (16,7)	1000 (16,7)
Usisna visina (maks.)	m	0,5 0,5
Minimalna duljina crijeva za dotok vode	m	7,5 7,5
Minimalni promjer crijeva za dotok vode	in	3/4	3/4
Podaci o snazi uređaja
Vrsta zaštite		IPX5	IPX5
Veličina standardne sapnice		045	045
Protočna količina, voda	l/h (l/min)	800 (13,3)	800 (13,3)
Radni tlak vode sa standardnom mlaznicom	MPa (bar)	20 (200)	20 (200)
Sigurnosni ventil za prekomjerni radni tlak (maksimum)	MPa (bar)	25 (250)	25 (250)
Radna temperatura tople vode (maksimalna)	°C	80	80
Snaga plamenika	kW	64	64
Potrošnja goriva (maks.)	kg/h (l/h)	5,9 (7,0)	5,9 (7,0)
Povratna udarna sila visokotlačne ručne prskalice	N	45	45
Pogonske tvari
Vrsta goriva		Dizel	benzin
Vrsta motornog ulja		SAE 10 W30, SAE 15 W40	SAE 10 W30
Količina motornog ulja	I	1,2	0,8
Gorivo		Loživo ulje EL ili dizel	Loživo ulje EL ili dizel
Crpka za vrstu ulja		15W40	15W40
Količina ulja pumpe	I	0,4	0,4
Dimenzije i težine
Težina (bez pribora)	kg 234	190
Duljina x širina x visina	mm	1130 x 910 x 895	1130 x 910 x 895
Zapremina spremnika goriva	I	4,5 6,0
Sadržaj spremnika goriva	I	30	30
Vrijednosti utvrđene prema EN 60335-2-79
Vrijednost vibracije šaka-ruka visokotlačne r učne prskalice	m/s^2	2,7 2,7
Vrijednost vibracije šaka-ruka cijevi za prskanje	m/s^2	<2,5	<2,5
Nesigurnost K	m/s^2	1	1
Razina zvučnog tlaka L_pA	dB(A)	99	92
Nesigurnost K_pA	dB(A)	3	3
Razina zvučne snage L_WA + Nesigurnost K_WA	dB(A)	116	109
CO2emisije prema postupku mjerenja iz Uredbe EU 2016/1628 Euro V
Motor	g/kWh	977,78	817,85

• Regulator temperature Slika C

- Elektrostarter motora Slika D

① Kontrolna lampica motornog ulja

② Prekidač motora

• Regulator temperature Slika C

- Prekidač motora Slika E

① Prekidač motora

- Prigušnica/slavina za gorivo Slika F

① Prigušnica

② Slavina za gorivo

Puštanje u pogon

⚠UPOZORENJE

Oštećene komponente

Opasnost od povreda

Proverite besprekorno stanje uređaja, pribora, dovoda i priključaka. Ako stanje nije besprekorno, ne smete koristiti uređaj.

Provera nivoa ulja visokopritisne pumpe

PAŽNJA

Mlečno ulje

Oštećenje uređaja

2006/42/EZ (+2009/127/EZ)

2011/65/EU

2014/30/EU

Primenjene harmonizovane norme

EN IEC 63000: 2018

EN 55012: 2007 + A1: 2009

EN 60335-1

EN 60335-2-79

EN 61000-6-1: 2007

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Тел.: [phone]

Факс: [phone]

Winnenden, 2020/10/01

Технически данни

Vee sisseimemine mahutist

Toode: Körgsurvepesur

Tüüp: 1.210-xxx

2006/42/EÜ (+2009/127/EÜ)

2011/65/EL

2014/30/EL

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel: [phone]

Winnenden, 2020/10/01

Tehnilised andmed

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

Winnenden, 2020/10/01

Tehniskie dati

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

Winnenden, 2020/10/01

Techniniai duomenys

H. Jenner
Chairman of the Board of Management

S. Reiser
Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Тел.: [phone]

Факс: [phone]

Winnenden, 2020/10/01

Black and white icon of a hand giving a thumbs-up gesture (no text or symbols)

THANK YOU!

Register your product and benefit from many advantages.

www.kaercher.com/welcome

Rate your product and tell us your opinion.

Icon showing a gear and wrench inside a square frame (no text or symbols)

www.kaercher.com/dealersearch

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28-40

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

QR code image with a central logo, likely linking to a digital resource or website.