RF44A5202SL - Fridge SAMSUNG - Free user manual and instructions

USER MANUAL RF44A5202SL SAMSUNG

English User servicing manual

1. You can check where to buy replacement parts at http://samsung.com

2. Visit the part purchase site and enter the model code of your product to check the parts

available for purchase. The model code is labelled on the outer side of your product. - You can check the model code and version on the barcode label at the bottom left of the product.

3. For replacement parts, make sure the part name matches that of the illustration in this

manual. - User-serviceable parts are limited to handles (some models only), gaskets, drawers, and hinges. NOTE Following the repair by a non-authorised service provider, self-repair or non-professional repair of the product, Samsung is not liable for any damage to the product, any injury or any other product safety issue caused by any attempt to repair the product which does not carefully follow these repair and maintenance instructions. Any damage to the product caused by an attempt to repair the product by any person other than a Samsung certied service provider will not be covered by the warranty. CAUTION

• The part name listed on the site may differ from that in this manual. Please make sure you choose the right part name.

• Replacing hinges requires extreme caution because it involves detaching the door.

• Be sure to wear safety gloves while making repairs. RF5000A_User-servicing-manual.indb 1 2020-12-22 5:45:14English The actual image and provided parts of the refrigerator may differ, depending on the model and the country.

• When replacing the door handle, take care not to scratch the front of the door.

• Firmly press the handles at the supports. Make sure there is no gap between the supports and the door.

• Tightly fasten the screws when attaching the handle.

• Check that the handle is rmly attached before using the product. Tools required (not provided) Hexagon wrench (4mm diameter) RF5000A_User-servicing-manual.indb 2 2020-12-22 5:45:14English To detach the handles Door Handle Freezer

1. Put the Hexagon wrench into the bottom

2. Turn the Hexagon wrench

counterclockwise. Allowance for loosening screws.

1. Put the Hexagon wrench into the bottom

hole of the handle. Turn the Hexagon wrench counterclockwise. Allowance for loosening screws.

2. Pull the handle (The other side disassemble

the same way). NOTE Turn the handle assembly though 90 degrees to allow access to the bottom xing position. RF5000A_User-servicing-manual.indb 4 2020-12-22 5:45:15English To attach the handles Door Handle Freezer

1. Attach the handle supports on the

grommet. NOTE Make sure that the grommet is properly mounted and the holes for handle disassemble are in the bottom.

1. Attach the handle supports on the

grommet. NOTE Make sure that the grommet is properly mounted and the holes for handle disassemble are in the bottom.

2. Turn the Hexagon wrench clockwise. For

holding the handle rmly. RF5000A_User-servicing-manual.indb 6 2020-12-22 5:45:15English Gasket replacement CAUTION Make sure you rmly attach the gasket. Otherwise, cold air from the refrigerator may leak. To remove the gasket

1. Pull the 4 corners of gasket.

2. Pull the center of gasket.

To replace the gasket Attach a new gasket to the refrigerator door. Make sure there is no gap between the new gasket and the door. RF5000A_User-servicing-manual.indb 7 2020-12-22 5:45:16English Drawer replacement CAUTION Check that the drawer is inserted properly into the rail during assembly. To remove the drawer Gently lift up the front of the drawer and slide out.

• We recommend that you remove the door bins before removing the drawer. This is to prevent damage to the door bins.

• To reinsert, insert the drawer into the frame rails and then slide inward. RF5000A_User-servicing-manual.indb 8 2020-12-22 5:45:16English Hinge replacement To replace the hinges, you must remove the doors rst. CAUTION

• When removing the doors, take extreme caution because the doors are heavy.

• Before replacing the hinges, put a soft pad such as cardboard on the oor to prevent scratches on the door when you place the doors down.

• As the hinges must be handled carefully and replaced by two or more persons, we recommend you to call for professional technical service.

• If you remove the hinge without holding the door, the door may fall and cause injury.

• Ensure that the shaft is rmly tightened on the hinge.

• Check that the hinge is rmly attached to the cabinet.

• Make sure the wire connectors are connected properly.

• Be careful not to damage the wires when fastening the top cover. WARNING

• Tilting/laying the refrigerator requires a minimum of 2 people.

• Disconnect the power cord before reversing the doors. Tools required (not provided) Phillips screwdriver Flat-head screwdriver Socket wrench 10 mm Pliers Allen wrench 5 mm RF5000A_User-servicing-manual.indb 9 2020-12-22 5:45:17English To replace the hinges WARNING Be careful not to drop and scratch the fridge door while removing the fridge door!

1. Use a Phillips screwdriver to remove the

screws fastening the top cover (A).

2. Disconnect the wires on the top of the

the screws fastening the top hinge (B).

4. Use a Phillips screwdriver to remove the

screw fastening the ground wire (C). RF5000A_User-servicing-manual.indb 10 2020-12-22 5:45:17English

5. Remove the top hinge from the door.

NOTE Remove the top hinge carefully. The wires from the door are arranged through the hinge shaft.

6. Gently pull up the fridge door to remove.

Do not apply excessive force to the door. The door may fall, causing physical injury.

7. Lay the door down on a at surface.

8. Lift the door straight up to remove. Be

careful not to drop and scratch the doors while removing them. Middle Hinge

9. Remove the screw attached to the left

and right middle hinges with a philips screwdriver (+). RF5000A_User-servicing-manual.indb 11 2020-12-22 5:45:17English

10. Remove the 2 hex head bolts attached to

the left and right middle hinges with an allen wrench (Ø 5 mm).

11. Reassemble in the opposite order of

disassembly after replacing the top, and/or middle hinge. CAUTION

• Make sure the wire connectors are connected properly.