Q: What is the ER2 error of the AC10/12V compressor and how can it be resolved?

The ER2 error of the AC10/12V compressor indicates an activated thermal protection after prolonged inflation. This is a normal safety mechanism. To resolve the issue: Immediately stop using the compressor Allow the device to cool down for 15-20 minutes in a dry and ventilated environment After cooling, you can normally reuse the device This protection automatically triggers to preserve the lifespan of the Li-ion battery. It does not indicate a malfunction - it is expected behavior during intensive or repeated inflations.

Q: Does this SCHEPPACH MR22561 lawn mower require a separate gearbox oil?

No, this mower does not require a separate gearbox oil. The SCHEPPACH MR22561 is equipped with a 4-stroke engine and a simple transmission system that does not require specific oil maintenance. However, you should regularly check the engine oil level (SAE 30 engine oil recommended for optimal performance). This is the main maintenance for this mower. Routine maintenance also includes: Regular replacement of the spark plug Cleaning or replacing the air filter according to the manufacturer's recommendations

Q: What does the flashing red light on the BRMR300 mean?

A flashing red light on the charging station of the BRMR300 indicates that the peripheral cable is damaged or improperly connected . How to resolve the issue: Check the cable connections: Ensure that both ends of the peripheral cable are securely plugged into the station. The red connector should be plugged into the "OUT" port and the black connector into the "IN" port. Inspect the integrity of the cable: Examine the cable along its entire length for cuts, cracks, or external damage. Clean the connectors: Metal connectors can accumulate dirt. Gently clean them with a dry cloth. Test with another power source: If possible, try again with another power supply to check that the station is functioning properly. If the cable shows visible damage or if the problem persists after checking the connections, the peripheral cable must be replaced. Contact SCHEPPACH customer service to order the replacement part.

Question 1

What is the ER2 error of the AC10/12V compressor and how can it be resolved?

Accepted Answer

The ER2 error of the AC10/12V compressor indicates an activated thermal protection after prolonged inflation. This is a normal safety mechanism.

To resolve the issue:

Immediately stop using the compressor
Allow the device to cool down for 15-20 minutes in a dry and ventilated environment
After cooling, you can normally reuse the device

This protection automatically triggers to preserve the lifespan of the Li-ion battery. It does not indicate a malfunction - it is expected behavior during intensive or repeated inflations.

Question 2

How to empty the residual grit from the SBT80 sandblaster?

Accepted Answer

To empty the residual grit left in your SBT80 sandblaster after use, follow this procedure:

Emptying Steps

Close the grit shut-off valve (referenced as item 12 in the manual) to prevent the grit from getting stuck in the distribution lines.
Wait for the pressure in the tank to drop completely to 0 bar (check the internal pressure gauge of the tank).
Slowly open the closure of the main tank (capacity 63 liters).
Carefully pour the grit through the opening of the tank into the funnel provided with the device to avoid splashes.
Remove the remaining residues at the bottom of the tank with the help of the funnel, tilting the device slightly if necessary.

Tip: This operation should be performed after each sandblasting session to keep the device in good condition and prevent the grit from hardening or rusting in the tank.

Question 3

How to unlock the blades when they do not open at startup?

Accepted Answer

If the blades of your ETHT1000 hedge trimmer remain stuck and do not open at startup, here are the checks to perform in this order:

1. Check the lubrication of the cutting bar

This is the most common cause. The cutting bar (part 1) must be lubricated after each use with an oil can or spray. If it lacks lubrication, the mechanism gets stuck and the pendulum blades cannot operate.

First, clean the bar with an oily cloth
Regularly apply oil along the cutting bar
Test after lubrication

2. Check the wear and integrity of the blades

The blades of the double cutting bar wear over time. Dull or damaged blades may not move properly.

Inspect the linear teeth of the bar for breaks or wear
If you find small breaks, smooth them with an oil stone
If the blades are very dull, have them sharpened or replaced by an authorized service

3. Check the tilt levers

The two notched levers (part 13) adjust the tilt of the bar to 10 levels. Make sure they are not in the locked position:

Gently maneuver the levers to unlock any potential mechanical jamming
The bar should be able to tilt freely

4. Check the motor startup

If the motor starts but the blades do not move at all:

Listen to the sound of the motor - it should be continuous and regular at 1000 min⁻¹
Check that the power cable is properly connected and intact
Test on another outlet to rule out a power supply issue

If after these checks the blades remain stuck, contact an authorized Scheppach service for a motor diagnosis or bar replacement.

Question 4

What are the vibration levels of the SCHEPPACH AB1900 demolition hammer?

Accepted Answer

The SCHEPPACH AB1900 demolition hammer emits two distinct vibration levels depending on the handle used:

Main handle: 17.447 m/s² (K=1.5 m/s²)
Auxiliary handle: 19.546 m/s² (K=1.5 m/s²)

The auxiliary handle generates a higher vibration than the main handle. This handle is adjustable: you can rotate it 360 degrees by loosening the clamping screw for better comfort during use.

Due to these vibration levels, wearing protective equipment is recommended during use: work gloves, safety glasses, and hearing protection.

Question 5

Is the main switch of the compressor replaceable?

Accepted Answer

No, the main switch (on/off switch) of the SCHEPPACH Air Force 5 compressor is not user-replaceable. It is not listed among the wear parts in the technical documentation.

The only replaceable parts as wear parts are:

The belt
The clutch

The main switch is a component of the electrical circuit that must remain under the manufacturer's control to ensure the safety of the device. If your on/off switch is not functioning properly (does not turn on, is stuck, or causes the circuit to trip), the compressor should not be used and must be taken to an authorized SCHEPPACH service center for inspection and replacement if necessary.

For regular maintenance, clean the device with a damp cloth and black soap, avoiding solvents. Consult customer service for any electrical repairs or interventions on the switch.

Question 6

What is the noise level (decibels dB) of the SCHEPPACH GSE45S shredder?

Accepted Answer

The SCHEPPACH GSE45S produces the following noise levels according to standardized testing methods:

Guaranteed acoustic power level: 92 dB(A) - maximum value guaranteed by the manufacturer
Measured acoustic power level: 89.1 dB(A) - value actually recorded during tests
Sound pressure level: 82.4 dB(A) - noise perceived near the device

The measurement uncertainty is 2.42 dB(A). The difference between the guaranteed level and the measured level reflects a slightly better performance than stated.

These values have been determined according to a standardized testing method that allows for comparison of different power tools. They may vary in practice depending on your usage: alternate between dry and wet debris to avoid clogging, let the machine run without load between inputs, and schedule regular breaks.

Essential hearing protection: at 82-92 dB(A), this shredder generates noise harmful to hearing. Wearing hearing protection (headphones or earplugs) is mandatory during use. Complement with regular maintenance, which reduces operating noise.

Question 7

Does this SCHEPPACH MR22561 lawn mower require a separate gearbox oil?

Accepted Answer

No, this mower does not require a separate gearbox oil. The SCHEPPACH MR22561 is equipped with a 4-stroke engine and a simple transmission system that does not require specific oil maintenance.

However, you should regularly check the engine oil level (SAE 30 engine oil recommended for optimal performance). This is the main maintenance for this mower.

Routine maintenance also includes:

Regular replacement of the spark plug
Cleaning or replacing the air filter according to the manufacturer's recommendations

Question 8

What does the flashing red light on the BRMR300 mean?

Accepted Answer

A flashing red light on the charging station of the BRMR300 indicates that the peripheral cable is damaged or improperly connected.

How to resolve the issue:

Check the cable connections: Ensure that both ends of the peripheral cable are securely plugged into the station. The red connector should be plugged into the "OUT" port and the black connector into the "IN" port.
Inspect the integrity of the cable: Examine the cable along its entire length for cuts, cracks, or external damage.
Clean the connectors: Metal connectors can accumulate dirt. Gently clean them with a dry cloth.
Test with another power source: If possible, try again with another power supply to check that the station is functioning properly.

If the cable shows visible damage or if the problem persists after checking the connections, the peripheral cable must be replaced. Contact SCHEPPACH customer service to order the replacement part.

Question 9

What is the impact force of the SCHEPPACH DI850 rotary hammer?

Accepted Answer

The technical manual for the SCHEPPACH DI850 does not specify the impact force in joules, but provides the following relevant characteristics:

Rated power: 850W (absorbed power 1050W)
Impact rate: 0-44,800 blows per minute
No-load speed: 0-2800 rpm

Drilling capacities:

Concrete: up to 20 mm
Metal: up to 13 mm
Wood: up to 30 mm

The high rate of 44,800 bpm and the power of 850W determine the effective impact capacity of this device. These specifications allow you to assess whether the rotary hammer is suitable for your drilling tasks.

Question 10

How to move and steer the SCHEPPACH HP1400S vibrating plate?

Accepted Answer

The Scheppach HP1400S vibrating plate moves thanks to the vibration of its motor and the reaction of the ground. Its movement and direction are primarily controlled via the guide handle (grip) and the throttle trigger.

To move the plate: hold the guide handle in hand, then fully open the throttle trigger to let the motor run at full throttle. The plate moves forward by itself. Use the throttle to control the speed of movement: full throttle for fast progression, reduced speed (idle) for slow movement or stopping.

To steer the plate: use the guidance of the handle and the pressure you apply by pushing or pulling. On flat terrain, the plate moves forward naturally. On an incline, slightly push the vibrating plate forward to maintain its progression. On sloped terrain, reduce speed by holding back the vibrating plate to control the descent. The maximum allowed incline is 20°.

Important points on compaction: the compaction depth reaches 20 cm. The number of passes required depends on the type and moisture of the soil. A certain level of moisture is necessary for good compaction. If the soil is very dry, pre-wetting may improve the result and reduce dust. Use the rubber mat (accessory provided) when compacting pavers to avoid damaging surfaces.

Warning: do not use on concrete or extremely hard, dry, or compacted surfaces. The vibrating plate tends to bounce on these surfaces, which may damage it as well as the motor. Refer to the manual for safety warnings (protective equipment: noise-canceling helmet, goggles, gloves, safety shoes, noise level 85.4 dB).

User manual SCHEPPACH : user manuals and guides in PDF

Models SCHEPPACH most viewed

Browse manuals SCHEPPACH by appliance type

Recent questions about devices SCHEPPACH