Q: How to perform the engine oil change?

Oil change schedule: First change after 25 hours of operation, then after every 100 hours of use. Oil change procedure: Position a catch basin under the engine Remove the hose (18) with a wrench, opening size 17 mm, and let the engine oil drain completely into the basin Be careful not to lose the sealing ring mounted on the hose (18) When the oil is completely drained, reattach the hose (18) to the device Engine oil filling: Unscrew the oil dipstick (14) Fill the engine with the recommended oil using a funnel Check the oil level using the dipstick (14) without screwing it back in initially The oil level should be at the midpoint of the dipstick Completely screw the oil dipstick (14) back in Recommended engine oil: SAE 10W-30 or SAE 10W-40 depending on the operating temperature. Engine oil capacity: Maximum capacity 600 ml (0.6 liters). The level should be at the central mark of the dipstick and should not exceed the filling neck. An insufficient oil level can damage the engine. Important: Perform this oil change on a flat and clean surface. Collect used oil in a suitable container for disposal in accordance with environmental regulations.

Q: How to drain the oil from the eccentric?

The eccentric oil change is recommended every 300 hours of operation . This operation uses a light gear oil SAE 80W-90 or 75W-90 , at a rate of 80 to 100 ml maximum . The PDF of this manual does not specify the exact location of the eccentric drain plug. On this type of vibrating plate, the eccentric is located under the lower casing. First, visually check by tilting the device or consulting the 'Spare Parts' section of the PDF to identify the eccentric component. General procedure: Stop the engine and let it cool completely Position a container under the eccentric to collect the used oil Unscrew the drain plug (appropriate wrench, usually 10-13 mm) Let the oil drain completely Replace the plug Fill the eccentric with new oil up to the mark (80-100 ml) If you cannot find a visible plug or if the eccentric appears sealed, contact SCHEPPACH support for clarification on your specific model.

Question 1

How to move and steer the SCHEPPACH HP1400S vibrating plate?

Accepted Answer

The Scheppach HP1400S vibrating plate moves thanks to the vibration of its motor and the reaction of the ground. Its movement and direction are primarily controlled via the guide handle (grip) and the throttle trigger.

To move the plate: hold the guide handle in hand, then fully open the throttle trigger to let the motor run at full throttle. The plate moves forward by itself. Use the throttle to control the speed of movement: full throttle for fast progression, reduced speed (idle) for slow movement or stopping.

To steer the plate: use the guidance of the handle and the pressure you apply by pushing or pulling. On flat terrain, the plate moves forward naturally. On an incline, slightly push the vibrating plate forward to maintain its progression. On sloped terrain, reduce speed by holding back the vibrating plate to control the descent. The maximum allowed incline is 20°.

Important points on compaction: the compaction depth reaches 20 cm. The number of passes required depends on the type and moisture of the soil. A certain level of moisture is necessary for good compaction. If the soil is very dry, pre-wetting may improve the result and reduce dust. Use the rubber mat (accessory provided) when compacting pavers to avoid damaging surfaces.

Warning: do not use on concrete or extremely hard, dry, or compacted surfaces. The vibrating plate tends to bounce on these surfaces, which may damage it as well as the motor. Refer to the manual for safety warnings (protective equipment: noise-canceling helmet, goggles, gloves, safety shoes, noise level 85.4 dB).

Question 2

Why does the engine of my SCHEPPACH HP1400S vibrating plate choke during acceleration and not hold idle?

Accepted Answer

An engine that chokes during acceleration and does not hold idle well is generally caused by a fuel supply issue or poor combustion. Here are the checks to perform on your SCHEPPACH HP1400S vibrating plate:

Fuel Check

Use the right fuel: Your 4-stroke engine consumes unleaded Super E5/E10. Make sure you are using this type of fuel. Poor quality gasoline or fuel that has been stored too long can create deposits that clog the carburetor.
Clean or replace the air filter: A clogged air filter reduces the oxygen supply necessary for combustion. According to the maintenance schedule, the filter should be cleaned or replaced every 50 hours. Check its condition and clean it if necessary.
Check the carburetor: If the engine chokes, it is often due to a clogged carburetor. You can attempt a cleaning with a specialized product poured into the tank, or completely drain the stagnant fuel and leave the tank in the off position for a few minutes to rinse it.

Engine Oil Check

Oil level: Check that the engine oil level is correct. Insufficient oil creates poor lubrication and reduces performance. Your engine requires 0.4 liters of SAE 10W-30 or 10W-40 oil.
Oil change: If you have not done the first oil change after 25 hours, the engine may be clogged. Perform an oil change to eliminate residues.

Ignition Check

Spark plug: A clogged or worn spark plug also causes misfires and a lack of power during acceleration. Inspect and clean the spark plug, or replace it (spark plugs should be checked every 50 hours according to the manual).

If after these checks the problem persists, it may indicate a deeper mechanical issue (valves, injection, compression). In this case, consult an authorized repairer or the technical support of the manufacturer SCHEPPACH.

Question 3

How to perform the engine oil change?

Accepted Answer

Oil change schedule: First change after 25 hours of operation, then after every 100 hours of use.

Oil change procedure:

Position a catch basin under the engine
Remove the hose (18) with a wrench, opening size 17 mm, and let the engine oil drain completely into the basin
Be careful not to lose the sealing ring mounted on the hose (18)
When the oil is completely drained, reattach the hose (18) to the device

Engine oil filling:

Unscrew the oil dipstick (14)
Fill the engine with the recommended oil using a funnel
Check the oil level using the dipstick (14) without screwing it back in initially
The oil level should be at the midpoint of the dipstick
Completely screw the oil dipstick (14) back in

Recommended engine oil: SAE 10W-30 or SAE 10W-40 depending on the operating temperature.

Engine oil capacity: Maximum capacity 600 ml (0.6 liters). The level should be at the central mark of the dipstick and should not exceed the filling neck. An insufficient oil level can damage the engine.

Important: Perform this oil change on a flat and clean surface. Collect used oil in a suitable container for disposal in accordance with environmental regulations.

Question 4

How to drain the oil from the eccentric?

Accepted Answer

The eccentric oil change is recommended every 300 hours of operation. This operation uses a light gear oil SAE 80W-90 or 75W-90, at a rate of 80 to 100 ml maximum.

The PDF of this manual does not specify the exact location of the eccentric drain plug. On this type of vibrating plate, the eccentric is located under the lower casing. First, visually check by tilting the device or consulting the 'Spare Parts' section of the PDF to identify the eccentric component.

General procedure:

Stop the engine and let it cool completely
Position a container under the eccentric to collect the used oil
Unscrew the drain plug (appropriate wrench, usually 10-13 mm)
Let the oil drain completely
Replace the plug
Fill the eccentric with new oil up to the mark (80-100 ml)

If you cannot find a visible plug or if the eccentric appears sealed, contact SCHEPPACH support for clarification on your specific model.

Question 5

Why won't the engine of my HP1200S vibrating plate start?

Accepted Answer

If the engine of your HP1200S vibrating plate refuses to start, check the following points in order:

1. Fuel Check

Only use unleaded gasoline with an octane rating above 90, as specified in the manual.
Check that the tank is not empty.
Ensure that the fuel valve, located on the tank, is set to ON.
If the gasoline has not been changed for more than a month, empty the tank and refill it with fresh gasoline.

2. Engine Oil Level Check

According to the maintenance manual, check the oil level before each use. An engine without sufficient oil cannot start.
Top up if necessary with the recommended oil.

3. Correct Starting Procedure

For a cold start, set the choke to CLOSED.
Pull the starter cable sharply and firmly. Do not pull gradually.
Once the engine has started, switch the choke to OPEN after a few seconds.

4. Additional Checks

Inspect the spark plug to ensure it is not dirty or worn.
Clean the air filter if it is dirty or clogged.

These checks cover the most common causes. If the engine still refuses to start after these checks, consult an authorized repairer.

User manual SCHEPPACH Vibratory plate : user manuals and guides in PDF

Models SCHEPPACH Vibratory plate most viewed

Other categories SCHEPPACH

Recent questions about Vibratory plate SCHEPPACH