Q: Where can I buy replacement blades for the SCHEPPACH RoboCut XL600?

The manual for the SCHEPPACH RoboCut XL600 recommends replacing the blades every 8 weeks to maintain optimal cutting performance. However, the PDF of the manual does not specify specific points of sale. To obtain compatible replacement blades, you can: Contact SCHEPPACH's official customer support Check authorized dealers of the brand Look at online retailers offering spare parts for robotic lawn mowers Make sure to order blades compatible with the XL600 model for optimal operation.

Q: What does the error code E1 mean on the SCHEPPACH RLM500W?

The error code E1 means that the mower is outside the working area defined by the boundary wire. Solutions to correct the E1 error: Check that the mower is indeed within the area defined by the boundary wire Ensure that the charging station is properly connected to the charger and the power supply Check that the boundary wires are tight and replace them if they are damaged Check that the boundary signal is working correctly by testing the mower manually at different locations near the wire If the problem persists after following these steps, the mower's boundary sensor may be faulty and require replacement.

Q: Where should the peripheral cable slot be located on the BRMR300 charging station?

According to the BRMR300 manual, the peripheral cable slot should be located under the charging station . The stripped cable (approximately 10 mm) first connects to the red "OUT" connector at the back of the station, then passes through this lower slot. For proper operation: After connecting to the terminals, the cable should extend straight for at least 100 cm in front of the station Maintain a minimum distance of 30 cm from the edges as recommended The station should be installed on a flat surface with at least 1 meter of free space without obstacles in front of it If your model has a different configuration (slot on top), check that you have not inverted the station or that the cable is not incorrectly wound. Routing the cable through the lower slot ensures its protection and proper retention during the mower's movements.

Q: Does the boundary wire need to go under the charging station of the BRMR300?

Yes, the boundary wire must go under the charging station. Here’s how to properly install the wire: Connect the end of the wire to the red terminal "OUT" located at the back of the charging station Pass the wire through the slot provided under the charging station Lay the wire in a loop around your working area 30 cm from the edges (or 8 cm in some special cases) Secure the wire with the provided pegs every 80 cm maximum, or bury it at a maximum depth of 3 cm Important point: Allow at least 1 meter of free space in front of the charging station, without obstacles, to enable the robot to access the charging base properly. If the indicator light on the station turns flashing red after installation, this indicates a wire problem (damaged or poorly connected). Check the connection to the OUT terminal and ensure there are no cuts.

Q: What does the flashing red light on the BRMR300 mean?

A flashing red light on the charging station of the BRMR300 indicates that the peripheral cable is damaged or improperly connected . How to resolve the issue: Check the cable connections: Ensure that both ends of the peripheral cable are securely plugged into the station. The red connector should be plugged into the "OUT" port and the black connector into the "IN" port. Inspect the integrity of the cable: Examine the cable along its entire length for cuts, cracks, or external damage. Clean the connectors: Metal connectors can accumulate dirt. Gently clean them with a dry cloth. Test with another power source: If possible, try again with another power supply to check that the station is functioning properly. If the cable shows visible damage or if the problem persists after checking the connections, the peripheral cable must be replaced. Contact SCHEPPACH customer service to order the replacement part.

Q: How to reset the BRMR300 mower and restart it?

Resetting and restarting the BRMR300 Complete reset (returns all settings to default): Press the reset button located on the control panel All settings will revert to factory values You will need to reprogram your mowing schedules afterwards Normal restart after a stop : Check that the STOP button is not activated (it would prevent operation) Press POWER ON/OFF to reactivate the device Enter the PIN code: 0000 (factory default code) A four-beep sound signal will sound before the blade is activated Press START then OK to begin mowing Note: If you enter the PIN code incorrectly 10 times in a row, the message "LOCK" will display for 10 minutes before trying again. After resetting, remember to reconfigure the date, time, and your usual mowing schedules (the default settings are Monday-Friday, 9 AM-3 PM).

Q: Where is the battery and overload sensor of the BRMR300 located?

Battery: The BRMR300 is equipped with a built-in lithium-ion battery AK2.0-RC-20Li (18V max 20V, 2000 mAh, 36 Wh). This battery is associated with the charging system of the docking station. It can be removed during maintenance or disposal of the robot. Overload sensor: The mower has an overload sensor whose malfunction triggers error code E6. This sensor is integrated into the robot's safety system. Although the user manual does not specify its exact location with a detailed diagram, it is generally located on robotic mowers as collision detection sensors situated at the front or on the sides of the chassis. Important: The manual states that the power must always be turned off when the mower is turned over for chassis maintenance. For precise location of internal components or in case of doubt, please consult Scheppach customer service.

Question 1

Where can I buy replacement blades for the SCHEPPACH RoboCut XL600?

Accepted Answer

The manual for the SCHEPPACH RoboCut XL600 recommends replacing the blades every 8 weeks to maintain optimal cutting performance. However, the PDF of the manual does not specify specific points of sale.

To obtain compatible replacement blades, you can:

Contact SCHEPPACH's official customer support
Check authorized dealers of the brand
Look at online retailers offering spare parts for robotic lawn mowers

Make sure to order blades compatible with the XL600 model for optimal operation.

Question 2

What does the error code E1 mean on the SCHEPPACH RLM500W?

Accepted Answer

The error code E1 means that the mower is outside the working area defined by the boundary wire.

Solutions to correct the E1 error:

Check that the mower is indeed within the area defined by the boundary wire
Ensure that the charging station is properly connected to the charger and the power supply
Check that the boundary wires are tight and replace them if they are damaged
Check that the boundary signal is working correctly by testing the mower manually at different locations near the wire

If the problem persists after following these steps, the mower's boundary sensor may be faulty and require replacement.

Question 3

Where should the peripheral cable slot be located on the BRMR300 charging station?

Accepted Answer

According to the BRMR300 manual, the peripheral cable slot should be located under the charging station. The stripped cable (approximately 10 mm) first connects to the red "OUT" connector at the back of the station, then passes through this lower slot.

For proper operation:

After connecting to the terminals, the cable should extend straight for at least 100 cm in front of the station
Maintain a minimum distance of 30 cm from the edges as recommended
The station should be installed on a flat surface with at least 1 meter of free space without obstacles in front of it

If your model has a different configuration (slot on top), check that you have not inverted the station or that the cable is not incorrectly wound. Routing the cable through the lower slot ensures its protection and proper retention during the mower's movements.

Question 4

Does the boundary wire need to go under the charging station of the BRMR300?

Accepted Answer

Yes, the boundary wire must go under the charging station.

Here’s how to properly install the wire:

Connect the end of the wire to the red terminal "OUT" located at the back of the charging station
Pass the wire through the slot provided under the charging station
Lay the wire in a loop around your working area 30 cm from the edges (or 8 cm in some special cases)
Secure the wire with the provided pegs every 80 cm maximum, or bury it at a maximum depth of 3 cm

Important point: Allow at least 1 meter of free space in front of the charging station, without obstacles, to enable the robot to access the charging base properly.

If the indicator light on the station turns flashing red after installation, this indicates a wire problem (damaged or poorly connected). Check the connection to the OUT terminal and ensure there are no cuts.

Question 5

What safety distance should be maintained between the boundary wire and obstacles?

Accepted Answer

According to the RoboCut XL600 manual, the recommended distances depend on your configuration:

Standard Distance

The gap between the peripheral cable and the outer cord (border of the area) must measure 30 cm.

Reduced Distance (special conditions)

A gap of 8 cm is acceptable only if all of these criteria are met:

The surface is passable (sidewalk, access path)
It is at the same level as the mowing area
No protruding or sharp parts that could damage the mower
No unwanted plants

Additional Safety

An obstacle of at least 15 cm in height must be placed between the peripheral cable and water bodies, slopes, embankments, or roads to protect the robotic mower.

Question 6

What does the flashing red light on the BRMR300 mean?

Accepted Answer

A flashing red light on the charging station of the BRMR300 indicates that the peripheral cable is damaged or improperly connected.

How to resolve the issue:

Check the cable connections: Ensure that both ends of the peripheral cable are securely plugged into the station. The red connector should be plugged into the "OUT" port and the black connector into the "IN" port.
Inspect the integrity of the cable: Examine the cable along its entire length for cuts, cracks, or external damage.
Clean the connectors: Metal connectors can accumulate dirt. Gently clean them with a dry cloth.
Test with another power source: If possible, try again with another power supply to check that the station is functioning properly.

If the cable shows visible damage or if the problem persists after checking the connections, the peripheral cable must be replaced. Contact SCHEPPACH customer service to order the replacement part.

Question 7

How to reset the BRMR300 mower and restart it?

Accepted Answer

Resetting and restarting the BRMR300

Complete reset (returns all settings to default):

Press the reset button located on the control panel
All settings will revert to factory values
You will need to reprogram your mowing schedules afterwards

Normal restart after a stop:

Check that the STOP button is not activated (it would prevent operation)
Press POWER ON/OFF to reactivate the device
Enter the PIN code: 0000 (factory default code)
A four-beep sound signal will sound before the blade is activated
Press START then OK to begin mowing

Note: If you enter the PIN code incorrectly 10 times in a row, the message "LOCK" will display for 10 minutes before trying again.

After resetting, remember to reconfigure the date, time, and your usual mowing schedules (the default settings are Monday-Friday, 9 AM-3 PM).

Question 8

What should I do if the STOP button on the BRMR300 remains activated and prevents the mower from restarting?

Accepted Answer

If the STOP button on the BRMR300 remains activated, the robot mower is intentionally immobilized (this is the normal operation of the STOP button: it immediately stops the robot and the blade). To restart the device, you must first deactivate this emergency stop.

Restart procedure:

Check that the STOP button is no longer pressed or activated (depending on the design of your model).
Press the POWER ON/OFF button to reactivate the device.
Enter the default PIN 0000 if prompted.
A sound signal will be heard (repeated four times) before the blade is activated.
Press START then OK to start mowing.

If the STOP button remains physically stuck or does not deactivate, check that no obstacles are interfering with its mechanism. In case of persistent malfunction of the button, contact SCHEPPACH customer service.

Question 9

How to configure and adjust the programming schedules of the BRMR300?

Accepted Answer

The BRMR300 is very easy to configure via the buttons on the control panel. Here’s how to adjust the main settings:

Set the mowing schedules

Press and hold the START button for 5+ seconds to access the basic settings. You can then configure the year, date, and time, which is essential for the mower to follow your programmed schedule.

Start time of mowing

Press and hold START + OK for 3+ seconds to change the daily start time. By default, the BRMR300 is set to start at 9:00 AM.

Operating duration

Press OK and hold for 3+ seconds to set the duration of each mowing session. The factory sets it for 6 hours by default.

Security PIN code

To change the initial PIN code (set to “0000”), press and hold START + HOME for 3+ seconds.

The BRMR300 is programmed by default to operate from Monday to Friday between 9:00 AM and 3:00 PM. Feel free to adjust these settings according to your needs - the mower handles lawns up to 300 m² with an adjustable cutting height from 20 to 50 mm.

Question 10

Where is the battery and overload sensor of the BRMR300 located?

Accepted Answer

Battery: The BRMR300 is equipped with a built-in lithium-ion battery AK2.0-RC-20Li (18V max 20V, 2000 mAh, 36 Wh). This battery is associated with the charging system of the docking station. It can be removed during maintenance or disposal of the robot.

Overload sensor: The mower has an overload sensor whose malfunction triggers error code E6. This sensor is integrated into the robot's safety system. Although the user manual does not specify its exact location with a detailed diagram, it is generally located on robotic mowers as collision detection sensors situated at the front or on the sides of the chassis.

Important: The manual states that the power must always be turned off when the mower is turned over for chassis maintenance.

For precise location of internal components or in case of doubt, please consult Scheppach customer service.

User manual SCHEPPACH Robot mower : user manuals and guides in PDF

Models SCHEPPACH Robot mower most viewed

Other categories SCHEPPACH

Recent questions about Robot mower SCHEPPACH