Q: How to effectively clean the BRAUN JB9040 blender?

The BRAUN JB9040 blender has a CLEAN program specifically designed for the automatic cleaning of the jug. For optimal daily cleaning, run this program immediately after each use. Fill the jug halfway with warm water, add a few drops of dishwashing liquid, and then start the program. The program stops automatically once the cycle is complete. After that, rinse the jug thoroughly and let it air dry. For a deep cleaning to be done about once a month , prepare a vinegar solution by diluting 500 ml of white vinegar (5% acid) in 500 ml of water, which represents a 1:1 ratio. Pour this solution into the jug, select the CLEAN program, and let the solution act for a maximum of 5 minutes after the program ends. Then rinse the jug thoroughly and let it air dry. This procedure effectively removes accumulated food residues and stains. The removable parts of the BRAUN JB9040 blender, including the blades and seals, are dishwasher safe for added convenience. You can clean them in the machine or manually according to your preferences. The Smoothie2Go bottle provided with the blender follows the same cleaning procedure as the main jug, both for the CLEAN program and for deep cleaning.

Question 1

How to replace or unlock the black gear plate above the motor?

Accepted Answer

The black gear plate above the motor (coupler) is an internal component that transmits the motor's rotation to the blades. If it does not turn the blades correctly, it may be due to several causes.

Before any intervention:

Always unplug the blender from the power source
Check that the bowl and the drive mechanism are properly assembled, as incomplete installation prevents the blades from turning
Remove the bowl to visually inspect the gear

Possible solutions:

Clogging: The plate may be blocked by dried food residues. Soak it in warm water for 30 minutes, then clean it with a soft brush or a small toothbrush.
Positioning: Ensure that the gear is properly positioned on its axis (it should click or fit correctly). Realign it and replace the bowl.
Mechanical wear: If after cleaning and realignment the blades still do not turn, the gear may be worn or damaged. This is a part that only a specialized technician can replace, as it is integrated into the blender's motor block.

For any repairs beyond cleaning and realignment, contact BRAUN customer service or an authorized repairer, as this part cannot be replaced by the user.

Question 2

How to effectively clean the BRAUN JB9040 blender?

Accepted Answer

The BRAUN JB9040 blender has a CLEAN program specifically designed for the automatic cleaning of the jug. For optimal daily cleaning, run this program immediately after each use. Fill the jug halfway with warm water, add a few drops of dishwashing liquid, and then start the program. The program stops automatically once the cycle is complete. After that, rinse the jug thoroughly and let it air dry.

For a deep cleaning to be done about once a month, prepare a vinegar solution by diluting 500 ml of white vinegar (5% acid) in 500 ml of water, which represents a 1:1 ratio. Pour this solution into the jug, select the CLEAN program, and let the solution act for a maximum of 5 minutes after the program ends. Then rinse the jug thoroughly and let it air dry. This procedure effectively removes accumulated food residues and stains.

The removable parts of the BRAUN JB9040 blender, including the blades and seals, are dishwasher safe for added convenience. You can clean them in the machine or manually according to your preferences. The Smoothie2Go bottle provided with the blender follows the same cleaning procedure as the main jug, both for the CLEAN program and for deep cleaning.

Question 3

How to assemble the mixing bowl of the BRAUN JB9040 mixer?

Accepted Answer

To correctly assemble the mixing bowl (jug) on your BRAUN JB9040 mixer, follow these essential steps:

Unplug the device before any handling to avoid any electrical risk.
Check for the centering block (4) - this is a crucial part that must never be missing when assembling the mixing bowl.
Place the mixing bowl on the motor base ensuring that the centering block is positioned correctly between the bowl and the base.
Press firmly on the bowl until it is well seated and stable on the motor base - it should not move sideways.
Check the lid (11) and its sealing ring - these elements must be correctly positioned and securely fastened before turning the device on.

Once the bowl is correctly assembled, plug in the device and turn it on. The touchscreen should light up and the START/STOP button should blink, indicating that the device is ready to use.

Important: Never attempt to use the BRAUN JB9040 mixer without the centering block (4) in place - this part is essential for safe operation and mixing efficiency. If the bowl does not assemble correctly, check that the centering block is properly positioned and that there are no residues on the contact surfaces.

Question 4

How to assemble the different parts of the BRAUN MultiQuick 7 MQ7035X hand blender?

Accepted Answer

To assemble your BRAUN MultiQuick 7 MQ7035X hand blender, follow these simple steps:

1. Identify the parts

You should have the main body of the blender (the handle with the motor), the removable lower part (blending foot), and possibly other accessories like a chopper or a whisk.

2. Attach the blending foot

Ensure that the blending foot is clean and dry.
Align the blending foot with the lower part of the handle.
Insert it and then turn clockwise until you hear a click, indicating that the attachment is secure.

3. Add accessories (if applicable)

To attach an accessory like a chopper or a whisk, proceed in the same way by aligning it and then turning until locked.

4. Check the attachment

Gently pull on the assembled parts to ensure they are securely attached before using the device.

This method ensures a safe and effective assembly of your BRAUN MultiQuick 7 MQ7035X hand blender.

Question 5

What does error code E3 mean on a BRAUN MQ775 immersion blender and how can it be resolved?

Accepted Answer

The error code E3 on a BRAUN MQ775 immersion blender generally indicates an issue related to motor overheating or a mechanical blockage. Here’s how to proceed to resolve this issue:

Steps to resolve error code E3:

Turn off and unplug the device: For your safety, always start by unplugging the blender from the electrical outlet.
Let the motor cool down: If you have used the device intensively, allow it to rest and cool down for 15 to 30 minutes to avoid overheating.
Check the accessories: Ensure that the accessories (blades, whisk, etc.) are properly attached and that no food is stuck in the blades or mechanism.
Clean thoroughly: Remove any food residues that could block the operation of the motor or blades.
Test again: Plug the device back in and turn it on to check if the error code disappears.

If the error code E3 persists despite these checks, it is possible that the motor is damaged or there is an internal issue requiring technical intervention. In this case, it is advisable to contact an authorized service center or a qualified professional for diagnosis and repair.

User manual BRAUN Blender : user manuals and guides in PDF

Models BRAUN Blender most viewed

Other categories BRAUN

Recent questions about Blender BRAUN