Q: What does error code EE 9 mean on the BRAUN ExactFit 3?

The error code EE 9 does not exist in the BRAUN ExactFit 3 manual. The blood pressure monitor only has the following error codes: E1 : The cuff is not properly attached - reposition it correctly E2 : The cuff is too tight - readjust with less tightness E10 / E11 : Movement detected during measurement - remain still E20 : Pulse signal not detected - loosen clothing on the arm E21 : Incorrect measurement - relax and try again If your device displays a code resembling EE 9, it is likely a typographical confusion with one of the codes above. Carefully check the exact message displayed on the screen and refer to the list above to identify the actual problem.

Q: What is the warranty period for the BRAUN ExactFit 3?

The manual for the BRAUN ExactFit 3 indicates a useful life of 5 years . However, the notice does not specify a specific commercial warranty duration (for example, 1 year or 2 years). To know the exact terms of your warranty and coverage details, BRAUN invites you to consult the Consumer Card available on the website http://www.hot-europe.com/fr/sav/ where you will find all the details and contact information for customer service. If you encounter a technical problem with your blood pressure monitor, you can directly contact the retailer or BRAUN customer service for further assistance.

Q: What does the TEST message displayed after changing the batteries mean?

The TEST message that appears after changing the batteries is an automatic startup test of the device. This is normal behavior for the BRAUN ExactFit 3 blood pressure monitor, allowing the device to check that the screen and basic functions are working correctly after installing the 4 AA alkaline batteries. After this TEST message, the device will automatically switch to date and time setting mode . You will need to configure these settings so that the results of your measurements are recorded with the correct time information. Once the date and time are set, your blood pressure monitor will operate normally: Press the Start button to take a measurement The LCD screen will display systolic and diastolic pressure as well as your heart rate The device will automatically turn off after 1 minute of inactivity With 4 new batteries, you can take about 300 measurements before needing to replace them again.

Question 1

What does error code EE 9 mean on the BRAUN ExactFit 3?

Accepted Answer

The error code EE 9 does not exist in the BRAUN ExactFit 3 manual. The blood pressure monitor only has the following error codes:

E1: The cuff is not properly attached - reposition it correctly
E2: The cuff is too tight - readjust with less tightness
E10 / E11: Movement detected during measurement - remain still
E20: Pulse signal not detected - loosen clothing on the arm
E21: Incorrect measurement - relax and try again

If your device displays a code resembling EE 9, it is likely a typographical confusion with one of the codes above. Carefully check the exact message displayed on the screen and refer to the list above to identify the actual problem.

Question 2

How to change the time display format to 24h on the BRAUN ExactFit 5 BP5900?

Accepted Answer

The BRAUN ExactFit 5 BP5900 does not offer an option to change the time display format between 12h and 24h.

After consulting the official manual, particularly the section Setting the month, date, and time, there is no setting available to switch between the two formats. The device displays the time in a fixed format that cannot be customized.

The available settings only allow you to modify:

The month
The date
The time (hours and minutes)

If you need a specific format, you can contact BRAUN customer service, but be aware that this limitation is related to the design of the device.

Question 3

How to set the time and date on the BRAUN ExactFit 5 BP5900?

Accepted Answer

To set the time and date on your BRAUN ExactFit 5 BP5900, follow these precise steps:

Access the setting mode: Press the Mode (5) button to make the month blink
Set the month: Use the ▲ (4) button to change the value (from 1 to 12), then press Mode
Set the date: Use the ▲ (4) button to adjust the day (from 1 to 31), then press Mode
Set the hour: Use the ▲ (4) button for the hour, then press Mode
Set the minutes: Use the ▲ (4) button for the minutes (from 0 to 59), then press Mode
Confirm: Press Mode one last time - the numbers stop blinking and your settings are saved

Tip: If you have just replaced the batteries, the device automatically enters time setting mode to ensure correct measurement recording.

Question 4

What is the warranty period for the BRAUN ExactFit 3?

Accepted Answer

The manual for the BRAUN ExactFit 3 indicates a useful life of 5 years. However, the notice does not specify a specific commercial warranty duration (for example, 1 year or 2 years).

To know the exact terms of your warranty and coverage details, BRAUN invites you to consult the Consumer Card available on the website http://www.hot-europe.com/fr/sav/ where you will find all the details and contact information for customer service.

If you encounter a technical problem with your blood pressure monitor, you can directly contact the retailer or BRAUN customer service for further assistance.

Question 5

What does the TEST message displayed after changing the batteries mean?

Accepted Answer

The TEST message that appears after changing the batteries is an automatic startup test of the device. This is normal behavior for the BRAUN ExactFit 3 blood pressure monitor, allowing the device to check that the screen and basic functions are working correctly after installing the 4 AA alkaline batteries.

After this TEST message, the device will automatically switch to date and time setting mode. You will need to configure these settings so that the results of your measurements are recorded with the correct time information.

Once the date and time are set, your blood pressure monitor will operate normally:

Press the Start button to take a measurement
The LCD screen will display systolic and diastolic pressure as well as your heart rate
The device will automatically turn off after 1 minute of inactivity

With 4 new batteries, you can take about 300 measurements before needing to replace them again.

User manual BRAUN Sphygmomanometer : user manuals and guides in PDF

Models BRAUN Sphygmomanometer most viewed

Other categories BRAUN

Recent questions about Sphygmomanometer BRAUN