Q: What weights is the CYBEX Solution S iFix car seat intended for?

The CYBEX Solution S iFix car seat is intended for children weighing between 15 and 36 kg , corresponding to groups 2 and 3 . These weight parameters generally correspond to children aged 3 to 12 years who are between 100 and 150 cm tall. However, the main criterion remains the child's height rather than their exact weight. If your child exceeds 135 cm in height, please consult the vehicle compatibility list provided in the manual to check the seat's adaptability.

Q: Is the backrest of the CYBEX Solution S2 iFix removable?

No, the backrest cannot be removed. It is a structural and permanent part of the seat that connects to the booster via a guiding peg to ensure the support and safety of the child. What can be removed: it is only the removable seat cover , which consists of 4 parts held by snap buttons. It can be machine washed at 30°C for maintenance. Important: According to safety standards, the child car seat cannot be modified or supplemented in any way without prior regulatory approval. If you are looking for a backless seat for an older child, you must choose a product specifically designed for that purpose.

Q: How to clean the Fangkörper of the CYBEX Pallas B2Fix + Lux child seat?

The Fangkörper is a specific protective shield for group 1 (children from 9 to 18 kg) of the CYBEX Pallas B2Fix + Lux child seat. This safety element must be kept clean to ensure its effectiveness and the safety of your child. The Fangkörper is part of the seat cover, which includes 5 elements (2 headrests, backrest, seat cushion, and Fangkörper). To remove the Fangkörper: Start by locating the snap buttons that secure the cover to the seat. Unlock all the snap buttons of the Fangkörper to detach the element from the rest of the seat. Proceed carefully to avoid damaging the material. Once released, the Fangkörper can be easily removed. To clean the Fangkörper cover: Wash the cover by hand or in the machine at a maximum of 30°C on a gentle cycle only. Caution: washing at a higher temperature or on a normal cycle will cause the fabric to fade. Always wash the cover separately from other clothes and linens. After washing, allow it to air dry in a dry place, away from the dryer and direct sunlight, which could damage the material. To clean the plastic elements of the Fangkörper: Use a soft cloth or a soft brush with a mild cleaning product and warm water . Never use harsh cleaning products, solvents, or bleach, as they may irreparably damage the plastic and safety joints. To reassemble the Fangkörper: Once all elements are completely dry, put the cover back on the seat following the assembly instructions in reverse. Carefully align all the snap buttons and press firmly until fully clicked into place. Ensure that the Fangkörper is securely attached and functional before using the seat. Regular maintenance keeps the hygiene and safety of the seat. If the Fangkörper shows signs of wear, cracks, or damage, replace it immediately according to the manufacturer's instructions, as it is a crucial safety element.

Question 1

Why does the CYBEX Cloud T i-Size car seat emit beeps or signal sounds?

Accepted Answer

The CYBEX Cloud T i-Size car seat may emit several types of sound signals during installation and use, all of which are normal safety signals:

Base installation signals

Continuous beep at startup: The ISOFIX base (T or Z2) emits a warning signal until it is correctly installed. This sound disappears once the ISOFIX arms are locked and the load leg has optimal contact with the ground.
Click sound: You will hear a distinct "CLICK" sound when the ISOFIX arms securely lock into the vehicle's anchor points. This is a good sign that the installation is secure.
Signal upon ground contact: Another signal may be heard when the load leg is properly pressing against the vehicle's floor.

Associated visual indicators

Alongside the sound signals, observe the ISOFIX indicators which should change from red to green to confirm that the seat is properly locked.

During use

Once correctly installed and locked, the seat should not emit regular beeps during use. If you hear unusual sounds while driving, check that the base is securely attached and that the seat remains locked in the rear-facing position.

Question 2

What weights is the CYBEX Solution S iFix car seat intended for?

Accepted Answer

The CYBEX Solution S iFix car seat is intended for children weighing between 15 and 36 kg, corresponding to groups 2 and 3.

These weight parameters generally correspond to children aged 3 to 12 years who are between 100 and 150 cm tall. However, the main criterion remains the child's height rather than their exact weight.

If your child exceeds 135 cm in height, please consult the vehicle compatibility list provided in the manual to check the seat's adaptability.

Question 3

Is the backrest of the CYBEX Solution S2 iFix removable?

Accepted Answer

No, the backrest cannot be removed. It is a structural and permanent part of the seat that connects to the booster via a guiding peg to ensure the support and safety of the child.

What can be removed: it is only the removable seat cover, which consists of 4 parts held by snap buttons. It can be machine washed at 30°C for maintenance.

Important: According to safety standards, the child car seat cannot be modified or supplemented in any way without prior regulatory approval. If you are looking for a backless seat for an older child, you must choose a product specifically designed for that purpose.

Question 4

How do I remove the Sirona G iSize seat from the ISOFIX base?

Accepted Answer

To remove the Cybex Sirona G iSize seat from its ISOFIX base, start by pulling the seat release handle (13) upwards to unlock the seat. Then slightly tilt the seat and lift it off the base (7). This first step only separates the seat from its base.

Once the seat is removed, you need to unlock the ISOFIX base by simultaneously and firmly pressing the ISOFIX release buttons (5) on both sides, while pulling them backwards. This double action unlocks the ISOFIX locking arms (6). Then pull the base (7) towards you to extract it from the vehicle's ISOFIX anchor points (8). Make sure to fully slide the ISOFIX locking arms (6) back to the transport position.

Finally, push the load leg (4) back to its original position and fold it completely. This step is important as it prevents the sound alarm from remaining active. A common issue encountered is that the ISOFIX buttons (5) are not pressed down with enough force or are not pressed simultaneously on both sides. Press firmly and at the same time on both buttons, then pull the base forward to completely release it from the anchor points.

Question 5

How do I adjust the headrest adjustment handle on the CYBEX Cloud T i-Size car seat?

Accepted Answer

The adjustable headrest of the CYBEX Cloud T i-Size car seat is adjusted using an adjustment handle to adapt the support to your child's growth. Here’s how to properly adjust this handle.

Location and operation: The adjustment handle is located at the back of the headrest (part no. 22 according to the documentation). To adjust the height of the headrest (part no. 21), grasp this handle at the back, pull or operate it to release the locking mechanism, then hold it while moving the headrest up or down to the desired position. Once the appropriate height is reached, release the handle to lock it in place.

Essential safety recommendation: When adjusting, ensure that there is no more than 2 cm (approximately the width of two fingers) of space between your child's shoulders and the headrest. This correct spacing ensures optimal support and maximum protection in the event of an impact. A poorly adjusted headrest would compromise both your child's comfort and protection and would prevent proper positioning of the harness system. Check this adjustment regularly, especially as your child grows, to maintain this safety throughout the use of the seat.

Question 6

How to adjust the position of the safety straps on the CYBEX Cloud T i-Size car seat?

Accepted Answer

To adjust the position of the safety straps on the CYBEX Cloud T i-Size car seat, you mainly need to adjust the height of the head support, which determines the position of the shoulder straps.

Steps to adjust the straps:

Adjusting the head support: Use the adjustment handle located at the back or on top of the head support to move it vertically. The support should be positioned so that the straps pass just above the child's shoulders, with about 2 cm of space between the support and the shoulders (approximately the width of two fingers).
Positioning the shoulder straps: Once the head support is adjusted, the straps automatically adjust to the correct height to pass over the child's shoulders.
Securing and tightening: Place the child in the seat, then tighten the straps by pressing the strap adjustment button and pulling on the central strap until the straps are snug but not too tight, ensuring safety and comfort.

Proper adjustment ensures that the straps hold the child securely in place while avoiding uncomfortable pressure points.

Question 7

How to clean the Fangkörper of the CYBEX Pallas B2Fix + Lux child seat?

Accepted Answer

The Fangkörper is a specific protective shield for group 1 (children from 9 to 18 kg) of the CYBEX Pallas B2Fix + Lux child seat. This safety element must be kept clean to ensure its effectiveness and the safety of your child. The Fangkörper is part of the seat cover, which includes 5 elements (2 headrests, backrest, seat cushion, and Fangkörper).

To remove the Fangkörper: Start by locating the snap buttons that secure the cover to the seat. Unlock all the snap buttons of the Fangkörper to detach the element from the rest of the seat. Proceed carefully to avoid damaging the material. Once released, the Fangkörper can be easily removed.

To clean the Fangkörper cover: Wash the cover by hand or in the machine at a maximum of 30°C on a gentle cycle only. Caution: washing at a higher temperature or on a normal cycle will cause the fabric to fade. Always wash the cover separately from other clothes and linens. After washing, allow it to air dry in a dry place, away from the dryer and direct sunlight, which could damage the material.

To clean the plastic elements of the Fangkörper: Use a soft cloth or a soft brush with a mild cleaning product and warm water. Never use harsh cleaning products, solvents, or bleach, as they may irreparably damage the plastic and safety joints.

To reassemble the Fangkörper: Once all elements are completely dry, put the cover back on the seat following the assembly instructions in reverse. Carefully align all the snap buttons and press firmly until fully clicked into place. Ensure that the Fangkörper is securely attached and functional before using the seat.

Regular maintenance keeps the hygiene and safety of the seat. If the Fangkörper shows signs of wear, cracks, or damage, replace it immediately according to the manufacturer's instructions, as it is a crucial safety element.

User manual CYBEX Car seat : user manuals and guides in PDF

Models CYBEX Car seat most viewed

Other categories CYBEX

Recent questions about Car seat CYBEX