Movekid - Car seat Axkid - Free user manual and instructions

USER MANUAL Movekid Axkid

Independent Marketing

www.infobebe.es

[e-mail]

([phone]

Polsc

Junior Andrzej Kwapinski

Horbaczewskiego 4-6

54-130 Wroclaw Dh Astra Sklep

Poland Tel. + (48) 713 549 723

Czech Republic

Domecek pro deti

www.domecekprodeti.cz

[e-mail]

([phone]

Romania

SC Baby Car seats

www. axkid.ro

[e-mail]

[phone]

New Zealand

Clicksafe

www.clicksafe.co.nz/axkid

axkid @ clicksafe.co.nz

Tel: [phone]

Suomi

Lastentarvike

www,lastentarvike.fi

[e-mail]

([phone]

Malaysia

SafenSound

www.safensound.com.my

[e-mail]

([phone]

Greece Eλαδα

Serbia Cp6nja

LETO shop

www.letoshop.gr

[e-mail]

([phone]

Eesti

GreenHansa OÜ

www.beebipood.ee

[e-mail]

([phone]

Latvia

Muki

www.muki.lv

[e-mail]

([phone]

Lietuva

Kotryna Group

www.kotrynagroup.com

[e-mail]

([phone]

South Africa

Quality Imports SA & #Carseatfullstop

wwwqualityimportssa.co.za.

[e-mail]

([phone]

Island

Leiftur

www.leiftur.is

[e-mail]

([phone]

Japan

Chameleon & Co. Inc.

www.chameleonco.jp

[phone]

EN 12-21

DE 22-31

ES 32-41

FR 42-51

IT 52-61

NL 62-71

PL 72-81

CS 82-91

SV 92-101

NO 102-111

DA 112-121

FI 122-131

ET 132-141

EL 142-151

IS 152-161

PT 162-171

RO 172-181

AR 182-191

JP 192-201

Thank you for choosing Axkid MOVEKID

Read this instruction manual before installing the car seat in your vehicle.

For more information and installation videos visit www.axkid.com.

Axdid MOVEKID is a rear-facing car seat approved for children with a height between 61-125 cm, ≤ 36 kg

Axkid MOVEKID is suitable for use from approximately six months of age, or from when your child can sit up unsupported.

This is an integral Specific vehicle Belted Enhanced Child Restraint System. It is approved according to UN Regulation No. 129, for use in compatible vehicle seating positions as indicated by the vehicle list. If in doubt, consult either the Enhanced Child Restraint System manufacturer (www.axkid.com) or the retailer.

Important information

To maximize your child's safety, it is important that you keep the following in mind:

Always follow the instructions in this manual. An incorrect installation may seriously affect the safety for your child. If in doubt, contact your retailer who can demonstrate a correct installation.
- Keep this instruction manual for future reference. If manual is lost, you can find it online at www.axkid.com
- Do not use the car seat in a seating position where an active frontal airbag is fitted. If you still wish to install the car seat in this location the airbag must be switched off according to the vehicle manufacturers instructions.
Should you have an accident, no matter how small, your car seat should always be replaced. It may have damage that is not visible and could seriously affect the safety of your child. For this reason, Axkid does not recommend purchasing secondhand car seats.
If the car seat has been exposed to direct sunlight, make sure the car seat is not too hot before installing your child.
- Never leave your child unattended in the vehicle.
- Ensure that any luggage or loose objects are secured in your vehicle as they may cause injuries to passengers in the event of an accident.
Ensure that the car seat is installed in a way where no parts become trapped by movable seats, car doors, etc.
If you are using lower tether anchorage straps, make sure they are installed in a way where they don't interfere with the movement of any vehicle seat.
The car seat may only be installed rear-facing.
Always make sure that the harness is adjusted to correctly fit your child's body. The harness is adjusted by moving the head support.
Make sure that the child's back is pushed against the car seat when restraining your child with the harness.
Always make sure that the harness is firmly tightened against your child and that the buckle is completely locked, you should not be able to pinch the straps.
Make sure there is no twist in the harness.
Always make sure the support leg is in its correct position and that is has contact with the vehicle floor. The support leg is a very important safety feature designed to maximise your child's safety in an accident.
Do not attempt to disassemble or modify any part of the car seat. The warranty and the safety performance of the car seat could be affected if doing so.
- Never use the car seat without the textile cover. The seat textile cover is a safety feature and may only be replaced with an Axkid original seat textile cover.
Read the vehicle handbook and the vehicle list at www. axkid.com to find which seating positions are suitable for this car seat.
- Axkid recommends to always use a seat protection to protect your vehicle seat from scratches and dirt.
If you have any doubts, contact the retailer where the car seat was purchased or contact [e-mail]

Table of content

Parts 14
Allowed and disallowed positioning of Axkid MOVEKID car seat 16
Lower Tether Anchorages 16
Installing lower tethers 17
Installing Axkid MOVEKID car seat in the vehicle 18
Restraining your child in Axkid MOVEKID car seat 19
Headrest adjustments 20
Removing Axkid MOVEKID car seat from the vehicle 20
Care and maintenance 21
Warranty 21

Parts

A HEADREST
B INTEGRAL HARNESS
C BUCKLE RELEASE BUTTON
D SEAT BELT SLOT
E HARNESS RELEASE BUTTON
F HARNESS TENSION STRAP
G HEADREST BRAKE LEVER
H ASIP PAD
HEEL
J VERTICAL LINE

K METAL CLIP CONNECTOR
METALCLIP
M ASP CONNECTOR
N LOWER TETHER
BELTCLAMP
P BELTCLAMPLID
Q SUPPORT LEG
R SUPPORT LEG BUTTON
SHOULDERSTRAP
T RECLINE ANGLE ADJUSTER

Allowed and disallowed positioning of Axkid MOVEKID car seat

A xid MOVEKID car seat can only be installed rear-facing. It will fit in most, but not all seating positions. Check your vehicle instruction manual to find suitable seating positions and check the vehicle list on www. axkid.com

Front passenger seat (no active airbag) YES/NO*
Front passenger seat (active airbag) NO
Rear passenger seat with 3-point seat belt YES
Seat with 2-point seat belt NO
Side and rear facing seats NO

IMPORTANT: If you wish to install your Axkid MOVEKID car seat in a location where a frontal airbag is fitted, the airbag must be disconnected according to your vehicle manufacturer instruction. Note that some vehicles require an authorized service centre to disconnect the airbag.

• The General Regulation of Traffic in Spain, in its article 117, establishes the prohibition of driving with children of stature equal to or less than 135 centimetres located in the front seats of the vehicle, without exceptions.

Lower Tether Anchorages Important info

Lower Tether Anchoring (LTA) are used to enhance the protection of children in cars by providing a firm and stable installation for extended rear-facing belt attached car seats. This increases the safety for your child in all types of collisions, including roll-over accidents and rear-end impacts.

Lower tethers are a well-established method that has been extensively used in the Nordic countries for over 40 years. In 2020 a new international standard for LTA, ISO13216-4:2020, was released. This standard describes the requirements for lower tethers for car seats but also for vehicle manufactures and their anchor points. The purpose is to improve the compatibility and ensuring a safe and easy way of installation for the future.

Axkid MOVEKID includes two lower tethers for installation in cars with or without lower tether anchorages. The included lower tethers complies with ISO13216-4:2020 to ensure a perfect fit, and easy installation, in vehicles with pre-installed lower tether anchorages that also complies to this standard. If your vehicle has anchorage points that do not comply with the standard, Axkid MOVEKID lower tethers are still likely, but not guaranteed, to fit.

Pre-installed lower tether anchorages in vehicles are often found on the seat rails attached to the floor, but other positions are also used. Check your vehicle's instruction manual for more information on usable anchor points.

A x kid MOVEKID comes with everything you need to install the car seat in your vehicle. However, lower tether anchorages and extra lower tether anchorage straps can be purchased separately and will make installation quicker and easier in multiple cars. Some vehicle manufactures also offers the possibility of retrofitting lower tether anchorages. Contact your vehicle manufacturer or dealer for more information. A x kid retrofit lower tether anchorages and extra lower tethers can be purchased separately.

Note: Never use Axkid MOVEKID without the lower tethers. They are an important safety feature and must always be used when installing your car seat.

Installing lower tethers

Always use two anchorage points when installing Axkid MOVEKID and choose anchorage points that are separated as this gives a more stable installation. Depending on your vehicle and the seat position where you choose to install your car seat, there are various possible anchorage points to use. See below for alternatives.

Lower tether routing options

alt. a

Install the tether around the seat rail in front of the car seat by threading the tether between the seat rail and vehicle floor or through an appropriate hole of the seat rail.

alt. b

Install the tether around the hinge of the vehicle seat in front of the car seat by threading the tether in between the vehicle seat back and seat cushion.

alt. C

Install the tether around the seat rail below the car seat by threading the tether between the seat rail and vehicle floor or through appropriate hole of the seat rail.

alt. d

Install the lower tether to a suitable anchorage point in the back of the vehicle and route the tether underneath the vehicle seat to the front of the vehicle. Make sure that the lower tether comes out from the front of the seat and not out from the sides.

alt.e

When installing the Axkid MOVEKID in the front passenger seat, the tether should be wrapped around the nearest suitable anchor point that will allow the straps to be tightened fully. Anchor points set further back can be used, and if needed, the tether can be crossed over and even looped together with another tether.

Note: Always make sure that changing the position of any vehicle seat does not interfere or damage the installed lower tethers.

Note: Never use sharp objects to assist in routing the tethers as it might damage the tethers.

LTA

When installing the Axkid MOVEKID using lower tether anchorages (LTA), the lower tether (N) can be looped around the metal clip connector (K), and the metal clip (L) should be connected to the lower tether anchor.

Installing Axkid MOVEKID car seat in the vehicle

Before installing AXKID MOVEKID, make sure you have installed the lower tethers or lower tether anchorages in your vehicle. See section about Lower Tether Anchorages and Installing lower tethers in this manual for more information and installation instructions.

1

Unzip the zipper and open the belt clamp lid (P).

2

Place the Axdid MOVEKID on the vehicle seat with the back of the car seat facing the front of the vehicle. Adjust the legroom for your child by simply moving the car seat back and forth on the vehicle seat. Axdid MOVEKID can be installed tight against the vehicle seat back but may never be installed with the heel (I) hanging over the edge of the vehicle seat. Make sure that the vertical line (J) on the heel (I) never crosses the edge of the vehicle seat.

Adjust the angle of the car seat by choosing a suitable recline position with the recline angle adjuster (T). For maximum safety, choose a position as upright as possible while also ensuring that your child's head does not fall forward when sleeping. For both comfort and safety reasons, the recline angle should be adjusted to a more upright position as your child grows. Note that when tensioning the lower tethers (N), the car seat will be slightly more reclined as it sinks into the vehicle seat cushion. When installing Axkid MOVEKID in a front passenger seat it is possible, but not necessary, for the back of the car seat to have contact with the dashboard.

3

Open the belt clamp (O). Pull out an arm length of the vehicle seat belt and thread it through the seat belt slot (D) closest to you. Route the belt through the belt clamp (O) and thread it through the seat belt slot (D) on the opposite side. Connect the vehicle seat belt with the seat belt buckle and pull hard on the shoulder part of the vehicle seat belt to remove all slack and to fasten the car seat, the harder you pull the firmer the installation. To give an even more firm and stable installation, press down on the car seat while pulling the vehicle belt. When the car seat is firmly fastened, close the belt clamp (O) and lock the vehicle seat belt in position. Make sure that both the shoulder and lap belt is locked together in the belt clamp (O). Close the belt clamp lid (P) and close the zipper.

4

Attach the metal clips (L) to the metal clip connectors (K) on each side of the child seat (or connect the metal clips (L) to the anchorages in your vehicle if lower tether anchorages is used for installation. See section Installing lower tethers in this manual for more information). Press down on the top of the car seat while tensioning the lower tethers (N). By tensioning the lower tethers (N) you also set the final recline angle of the car seat. Keep pushing down and tensioning the car seat until it is firmly fastened, and you have achieved a suitable recline angle.

5

Pull out the support leg (Q) from the car seat. Push the support leg button (R) and pull the support leg (Q) downwards until it is in contact with the vehicle floor. Let go of the support leg button (R) and lift the car seat upwards to further extend the support leg (Q) until you hear a click. The support leg (Q) should now be locked and firmly pressed against the vehicle floor. Make sure that the support leg (Q) is angled about 10^ towards the front of the vehicle. Check the vehicle seat belt again to make sure that it is still firmly tensioned and that no slack has occurred in the hip belt while tensioning the lower tethers and support leg. If the vehicle belt has lost some tension, simply re-tension it by repeating step 2 of this guide without disconnecting the lower tethers.

6

Push the ASIP pad (H) into the slots on the ASIP connector (M) and slide downwards, the ASIP pad (H) will click into place. If there is a plastic cover on the ASIP connector (M), remove it and place it on the ASIP connector (M) on the opposite side of the seat before fitting the ASIP pad (H). Make sure the ASIP pad (H) is attached on the side of the Axkid MOVEKID car seat that is closest to the vehicle door.

Restraining your child in Axfid MOVEKID car seat

Before restraining your child in the Axlid MOVEKID car seat, make sure you have the correct inlay installed in the seat. Axlid MOVEKID is designed to grow with your child and to ensure a comfortable and safe fit for the children. Axlid recommends using the inlay until it is too tight for your child, but to a minimum length according to table below (note that the age is just an indication):

Age Height
Toddler 0-3 years	61-105 cm
Child 3-7 years	106-125 cm

The Axdid MOVEKID is equipped with an adjustable headrest (A). See section Headrest adjustment for more information.

Adjust the headrest (A) to an approximate position for your child.

Loosen the harness by pressing the harness release button (E) and pull out both shoulder straps (S) at the same time. Avoid pulling only one strap at the time since it may cause the shoulder straps (S) to become uneven.

Unlock the harness buckle by pressing the buckle release button (C) and place the straps outside of the seat.

Place your child in the seat and place the shoulder straps (S) over your child's shoulders. Pull and hold the headrest brake lever (G) to unlock and keep the headrest unlocked. Push down/pull up the headrest (A) to a position where the shoulder straps are located maximum 1 cm above the child's shoulders. Lock the harness by first positioning the parts of the buckle that is attached to the shoulder straps (S) together, and then push them into the buckle until you hear a click.

Pull on the shoulder straps (S) to tighten the harness over your child's hips. While keeping tension in the shoulder straps (S), pull the harness tension strap (F) straight from the car seat until the harness is tightened enough, you should not be able to fit more than one finger between the shoulder straps (S) and your child's shoulders.

Headrest adjustment

The Axkid MOVEKID is equipped with an adjustable headrest (A).

Always ensure that the headrest is positioned in the correct height for your child when using your Axkid MOVEKID child seat. Check that the shoulder straps (S) are going through the seat straight from your child's shoulders or maximum 1 cm above. If not, adjust the headrest (A) accordingly.

Note: The harness tension needs to be released if the headrest cannot be pulled up to a suitable height. Press the belt harness release button (E) to loosen the harness.

Removing Axkid MOVEKID car seat from the vehicle

Unzip the zipper and open the belt clamp lid (P). Unlock the vehicle seat belt by pressing the red button on the seat belt buckle. Open the belt clamp (O) and pull the vehicle seat belt and guide it through the seat belt slots (D) to remove it from the car seat.
Unlock the lower tethers (N) by holding on to the connectors with your hand and pressing on the grey button with your thumb. While keeping the connector in your hand, slowly push to extend the lower tethers.
- Push the support leg button (R) and collapse the support leg (Q) to its shortest position.
- Fold the recline angle adjuster (T) to its folded position. Lift the Axkid MOVEKID out of the vehicle.

Tip: Lock the harness buckle and tension the harness before removing the car seat from the vehicle. You can then use the shoulder straps (S) as a carrying handle, making it easier to lift out the car seat and transporting it outside of the vehicle.

Important: Never carry the car seat by holding in the headrest (A).

Recycling your car seat

Axlid strongly recommends recycling of old car seats. Before leaving the seat at your local recycling station cut off the harness straps from the seat, remove the textile cover, remove as many Styrofoam parts as possible, separate metal and plastic parts if possible. The main part of the seat should be marked unsafe or expired (use a marker) to deter anyone from using it again. Please check your local municipal guidelines for recycling instructions for the different materials.

Care and maintenance

The seat textile cover can be machine washed at 30^ C on a gentle cycle. Do not put the cover in a dryer as this can damage the cover and the padding may separate from the fabric. Visit www.axkid.com to find videos explaining how to remove and attach the cover.

If the textile seat cover needs replacing, ensure only original products from Axlid are used. If other products are used, the Axlid car seat's safety system may be compromised and could lead to severe injury in case of an accident.

Any plastic parts of the Axkid car seat can be cleaned with mild detergent and water. Do not use aggressive chemicals containing solvents or similar, as this can cause damage to the plastic and compromise the safety of the car seat.

Remove the textile cover:

• Remove the ASIP pad (H) if attached.
  Pull the headrest (A) to its topmost position. Loosen the harness by pressing the harness release button (E) and pull out both shoulder straps (S) at the same time.
  Unzip the two zippers on the underside of the headrest (A) and carefully pull the cover off from the headrest (A).
• Lower the headrest (A) to its lowest position.
  Unlock the harness buckle by pressing the buckle release button (C) and remove the buckle cover.
  Unzip the zipper and open the belt clamp lid (P) and remove the plastic lid from the textile cover.
• Open the 4 buttons on the textile cover on the backside of the car seat.
  Unzip the two zippers at the backrest on the inside of the car seat and gently remove the textile cover from the car seat. Be careful around the ASP pad and other plastic covers to avoid damaging the textile. Don't pull too hard.
• Open the shoulder pads and gently remove them from the Velcro.

Install the textile cover:

• Reverse the steps from the instruction above to install the textile cover on the car seat again.

Note: The shoulder pads can be installed at different positions. Install them in a position suitable for your child, the shoulder pads should be positioned on top of the shoulder and on the chest of your child. Also make sure that the rubber side of the shoulder pad is facing your child's chest.

Warranty

The Axkid car seat is covered by a 24-month warranty from date of purchase. Ensure you save your receipt and bring it to your place of purchase if you have any warranty issues.

The warranty does not cover:

Normal wear and tear.
- Damage due to incorrect use, neglect, or accident.
If repairs have been carried out by a third party.
All materials used have a very high UV-resistance rating. However, UV-light is very aggressive and will ultimately lead to fading of the seat cover. This is not covered by our warranty as it is considered normal wear and tear.
- Handle the seat with care. Never carry the seat by holding in the headrest (A).

Sigma 100 mg/kg (100 mg/kg) is a standard of care for treating patients with acute coronary syndromes. The drug has been used in the treatment of ischemic heart disease, including myocardial infarction, stroke, and peripheral vascular disease.

5

TpaBnE TPOC TA EeW TO IODI OTnHEnC (P) ATO TO KAeIOA AutOKIVNTOU. NIEOT TO KOUMI TOU IOIou OTnHEnC (P) KAI TpA BnE To nOoi OTnHEnC (P) TPOC TA KATw eXPI VA EeEe O E ENAPN ME TO DAnEO TOAU TKOKIVNTOU. APNOTE TO KOUMI TOU IOIou OTnHEnC (P) KAI ONKWOT TO KAeIOA AutOKIVNTOU POC TA TAVW YIA VA ETEKTEIVE TEPaIETPO TO IODI OTnHEnC (P) MEXVI VA AKOUOTE EVA KAIK. TO IODI OTnHEnC (P) INPETEI TOWA VA EEXI aapalaioei KAI VA NIEZETAI OTAEPa OTO DAnEO TOU OxmuoC. BeaIwEeite OTI TO nOoi OTnHEnC (P) Bpioketai OE yovia Tepinou 10^ POC TO IMPOITVO MEOC TOU OxmuoC. EEvEeTe Xav Tzwn aopaaieiac Tou Oxmuatoyia VABeBAIWte DTivai Akopa axPTa TeVTWevn KAI OTI DEV EExI Eupaviotei xalapwn OTN Zwn Meonc Evw TeVTWVE TIC KATW PooDBeOic KAI TO nOoi OTnHEnC. EaV n ZwvN TOU OxmuoC Exei xalapwoi, anla TeVTWTE Tnv Gava Etnaaamabavovtac To bma 2 autou TOU oDnyou Xwipv a anouuvdoeTe TIC KATW PooDBeOic.

6

Piote to ASIP (H) otic unofoxc tou ouvdoou ASP (M) kai oupe Te npoc ta katw, to ASIP (H) 0Koumuoei oTn 0eou. Eav utapxe eva Iaoitko kaumu aotov ouvdoo ASP (M), aphiote to Kai toioetne To OTov ouvdoo ASP (M) otnv avrietn nAepa Tou kaiogatoc npiv tnoetnoeTe to aiaIAPaki ASP (H). Beaiowte oTI to ASP (H) eivai otpeewevo otny nAepa Tou kaiogatoc autokivntou Axdik MOVEkID TousivianovnpaTOAUOKIVHTOU.

aalll aaii aai iiaai laiy 1aeg yag gagg aaggl aagl aay! baaagall

Ji j 1 Js y Ls . jy 1 1 jy 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Jlalab Jlaizim Jabi Jclao Aykid 2 ylll lq. alab ao jub

Ae 1

all do all do

gag klll lal! g aee eaae aeae aee

S = S

1

5y

J 1000000000000000000000000000000000000000000

jolal jai jaiiyw yllab ciuyuie sylall gns jalb lgl

a 1 a 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

10

aalei aaii 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Jg j 10

a 1

puee 1000 1000 1000

Axdid joo waeill joe geos yao oohy y all

1.128 5jwll (s)sl awl lall wgl all slal 4eal www. axkid.com (le 1jwll aaasg yjwll ayis

yglalg wgd jol yjw daa aalal alal Axlal axkld 5x

[e-mail] 2015

AR

A
B aol

jolalpaiaD

jlox 1240s y

jolalalaa

G

Jlaal Jn Axl Axl Axl Axl

(ASIP)

H

122all

S木弟形 COBD = S COD + S BDO = S BOC +

K

G

Axlall jia Axlall Axkid J (ASIP)

aull

M

Ojoll ayu

aljol cluo oolR

a

JnJ 1 JwB

S a

1

Jd

Lg. b1sI J 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

aaii iiaii iiojai jss

aall 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

alt. a

Jaa aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aal aAL

100 100 100 100

aalil 1 a j 1 b i

a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a

J 1

Axlalblal 1s k jk 1s. Axlal 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s 1s

aagall aull 1g So jy Axlalll aoj Axlil Axkid MOVEKID Jlebl Ie oI y:

Jlal 1d Axlkld MOVEKID

Axkid MOVEKID 2000.
Axdal yu wlll lal baiy jn no sL Axdid MOVEKID Jab11 2000.
gwhl Axkid ggi. Jab11 no na laa yggw o ng aag gao daa qg bi yu b
jull jn b2) yllf Jgdl lgaog jgbll no g u d n sllepb wppn paae i j

		الإستعمال
	105 16 61	الإستعمال
	125 106	7 13 3 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 10000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000

aagaae aee

Aaolil 1

7

（）

8

1

9

10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

HC

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

11

Axkid MOVEKID 1

a 1 a 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

（g）pJnll 1000 1000

Jlalll Jg) Jlal 15 (j) aaiall cayag (J) ayall alall J
J, uill aiaa tial wll tii Ii Jt iis 15 11 Jilaw w Cunill blau (J) aiall
jll le Jw ll bni. (Ilogall no jaiu kll lio g Aowf Cooj
Aaiell tial aaj Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jn Jnn

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

aiaaiall aalll no ayalall Jago caii (c) ayilal all clalln no ayalall slyw glaol

1

2

3

4

5

6

iiaiaiaia

J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15 J 15

g 11 (g) dwwall gaw w dwwall glw jglb

11 1

aaii i 1

（1）wJllssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssss

Jlab31 2000000000000000000000000000

Jgdd 1 Jg d aal l j Jg. aal 1aag 8 8 Axl 8 g 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8

Axkid MOVEKIDを選んだalityかはうごきいま