GSR 18 VEEC - Screwdriver BOSCH - Free user manual and instructions

USER MANUAL GSR 18 VEEC BOSCH

OBJ_BUCH-2671-001.book Page 3 Friday, January 22, 2016 11:09 AM1 609 92A 1RB | (22.1.16) Bosch Power Tools 4 | GSB 18 VE-EC

OBJ_BUCH-2671-001.book Page 4 Friday, January 22, 2016 11:09 AM5 | 1 609 92A 1RB | (22.1.16) Bosch Power Tools

Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.

Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory or fastener may contact hidden wiring. Cutting accesso- ry and fasteners contacting a “live” wire may make ex- posed metal parts of the power tool “live” and could give the operator an electric shock. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility com- pany for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property dam- age. Switch off the power tool immediately when the tool in- sert jams. Be prepared for high reaction torque that can cause kickback. The tool insert jams when: — the power tool is subject to overload or — it becomes wedged in the workpiece. Hold the machine with a firm grip. High reaction torque can briefly occur while driving in and loosening screws. When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more secure with both hands. Secure the workpiece. A workpiece clamped with clamp- ing devices or in a vice is held more secure than by hand. Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of control over the power tool. Do not open the battery. Danger of short-circuiting. Protect the battery against heat, e. g., against continuous intense sunlight, fire, water, and moisture. Danger of explosion. In case of damage and improper use of the battery, va- pours may be emitted. Ventilate the area and seek medical help in case of complaints. The vapours can irri- tate the respiratory system. Use the battery only in conjunction with your Bosch power tool. This measure alone protects the battery against dangerous overload. The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit can occur and the battery can burn, smoke, explode or overheat. The battery is supplied partially charged. To ensure full battery capacity, completely charge the battery in the battery charger before using for the first time. Read the operating instructions of the battery charger. Adjust the gear switch only when the machine is at a complete stop. Always push the gear selector and turn the operating mode selector switch through to the stop. Otherwise, the machine can become damaged. Before any work on the machine (e. g., maintenance, tool change, etc.) as well as during transport and stor- age, set the rotational direction switch to the centre position. Unintentional actuation of the On/Off switch can lead to injuries. Product Description and Specifica- tions Read all safety warnings and all instruc- tions. Failure to follow the warnings and in- structions may result in electric shock, fire and/or serious injury. While reading the operating instructions, unfold the graphics page for the machine and leave it open. Intended Use The machine is intended for driving in and loosening screws as well as for drilling in wood, metal, ceramics and plastic. GSB machines are additionally intended for impact drilling in bricks, brickwork and masonry. The light of this power tool is intended to illuminate the power tool’s direct area of working operation and is not suitable for household room illumination. Product Features The numbering of the product features refers to the illustra- tion of the machine on the graphics page. 1 Tool holder 2 Keyless chuck OBJ_BUCH-2671-001.book Page 14 Friday, January 22, 2016 11:09 AMEnglish | 15 Bosch Power Tools 1 609 92A 1RB | (22.1.16) 3 Depth stop 4 Auxiliary handle (insulated gripping surface) 5 Intermediate piece of auxiliary handle 6 Wing bolt for depth stop adjustment 7 Torque presetting ring 8 Mode selector switch 9 Gear selector 10 Colour clip 11 Belt clip 12 Battery pack 13 Battery unlocking button 14 Worklight 15 Overload protector indicator 16 Universal bit holder* 17 Rotational direction switch 18 On/Off switch 19 Handle (insulated gripping surface) *Accessories shown or described are not part of the standard de- livery scope of the product. A complete overview of accessories can be found in our accessories program. Technical Data Noise/Vibration Information Sound emission values determined according to EN 60745-2-1, EN 60745-2-2.

GSR 14,4 VE-EC / GSR 18 VE-EC

Typically the A-weighted sound pressure level of the product is less than 70 dB(A). Uncertainty K =3 dB. The noise level when working can exceed 80 dB(A). Wear hearing protection! Cordless Drill/Driver Combination Cordless Drill

Maximum torque, hard screwdriving appli- cation according to ISO 5393 Nm 70

Maximum drilling diameter (1st/2nd gear) – Wood – Steel – Brickwork

Max. screw dia. mm 10 12 10 12 Weight according to EPTA-Procedure 01:2014 kg 2.1* 2.2* 2.2* 2.3* Permitted ambient temperature – during charging – during operation

*depending on the battery pack being used ** limited performance at temperatures <0 °C OBJ_BUCH-2671-001.book Page 15 Friday, January 22, 2016 11:09 AM16 | English 1 609 92A 1RB | (22.1.16) Bosch Power Tools

GSB 14,4 VE-EC / GSB 18 VE-EC

Typically the A-weighted noise levels of the product are: Sound pressure level 87 dB(A); Sound power level 98 dB(A). Uncer- tainty K =3dB. Wear hearing protection! The vibration level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with anoth- er. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main ap- plications of the tool. However if the tool is used for different applications, with different accessories or insertion tools or is poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may sig- nificantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work pat- terns. Assembly Battery Charging Note: The battery supplied is partially charged. To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time. The lithium-ion battery can be charged at any time without re- ducing its service life. Interrupting the charging procedure does not damage the battery. The lithium-ion battery is protected against deep discharging by the “Electronic Cell Protection (ECP)”. When the battery is empty, the machine is switched off by means of a protective circuit: The inserted tool no longer rotates. Do not continue to press the On/Off switch after the machine has been automatically switched off. The bat- tery can be damaged. Removing the battery The battery 12 is equipped with two locking levels that should prevent the battery from falling out when pushing the battery unlocking button 13 unintentionally. As long as the battery is inserted in the power tool, it is held in position by means of a spring. To remove the battery 12, press the unlocking button 13 and pull out the battery toward the front. Do not exert any force. Auxiliary Handle Operate your machine only with the auxiliary handle 4. Before performing any work, make sure that the auxil- iary handle is firmly tightened. Loss of control can lead to injury. Mounting the Auxiliary Handle To open the auxiliary handle, turn the bottom part of the aux- iliary handle 4 in counterclockwise direction. Pull back the intermediate piece of the auxiliary handle 5 and hold it in this position. Slide the auxiliary handle over the drill chuck to mount the auxiliary handle on the power tool. Then let go of the intermediate piece 5. Afterwards, tighten the bottom part of the auxiliary handle 4 again by turning in clockwise direction. Changing the position of the auxiliary handle The auxiliary handle 4 can be set to any position for a secure and low-fatigue working posture. GSR 14,4 VE-EC GSR 18 VE-EC GSB 14,4 VE-EC GSB 18 VE-EC Vibration total values a

(triax vector sum) and uncertainty K determined according to EN 60745-2-1, EN 60745-2-2. Drilling in metal:

Impact drilling in concrete:

OBJ_BUCH-2671-001.book Page 204 Friday, January 22, 2016 11:09 AM한국어 | 205 Bosch Power Tools 1 609 92A 1RB | (22.1.16)