Q: What is the duration of the intensive cotton program of the FAR LF510L23W?

On the FAR LF510L23W washing machine, the duration of the intensive cotton program varies according to the selected temperature: Intensive Cotton 60°C: 3 hours 53 minutes Intensive Cotton 40°C: 3 hours 48 minutes This extended program is designed to enhance the washing effect and clean your textiles more deeply. The duration may vary slightly depending on the load and the type of fabric.

Q: How to drain the water from the FAR LF510L23W washing machine?

Here’s how to drain the water from your FAR LF510L23W: Stop and unplug the machine, then make sure it has completed its washing cycle Open the cap of the lower cover located at the bottom of the appliance Turn the filter counterclockwise to access it Let the water completely drain through the drain filter Wait for the water to cool before handling the filter - risk of burns Take the opportunity to clean the filter : remove any accumulated foreign materials Close the lower cover after cleaning Maintenance tip: Repeat this operation every 3 months to ensure the proper functioning of your machine.

Q: What cover should be removed to access the bulb on the FAR FMO20 microwave?

Important safety notice: Before any handling, completely unplug the FAR FMO20 microwave from its electrical outlet. The replacement of the lighting bulb should only be undertaken if you are comfortable with this operation, as it is strongly advised against for unqualified individuals to perform operations involving the removal of covers that protect against exposure to microwave energy. On the FAR FMO20, the lighting bulb is located behind a viewing window (porthole) usually found on the top of the microwave, just behind the control panel . To access it, you need to remove a small plastic protective cover or porthole. Access procedure: Unplug the device from its power source (230 V) and wait a few minutes for all components to cool down. Locate the porthole cover : look for a small translucent or opaque plastic plate, usually square or round, located on the top or on the right side of the microwave, near the control panel. Unscrew or remove the cover that protects the lighting porthole. Depending on the model, it may be secured by one or two screws to be removed with an appropriate screwdriver (usually a flat screwdriver). Access the bulb : once the cover is removed, you will see the lighting bulb. It is usually a pin or screw type, depending on your microwave version. Replacement: If the bulb needs to be replaced, use a compatible replacement bulb for the FAR FMO20 (original type and wattage). Never use a higher wattage bulb, as it could damage the lighting system. After replacement, reinstall the cover and screws, tightening them lightly. If you have difficulty locating the cover or are unsure about handling the device, contact FAR customer service or consult a qualified repair technician to perform this operation safely.

Q: What does the error code dE F2 mean on the FAR MOE30S microwave and how can it be resolved?

The error code dE F2 on the FAR MOE30S microwave indicates that the device has detected a problem with the door or its safety system. This code appears when the device cannot confirm that the door is properly closed, either because it is not closed correctly or due to a faulty door sensor. First step: Check the door closure Open the microwave door completely and check that no obstacles are preventing it from closing. Close the door firmly until you hear a locking click. The door must be properly engaged. Gently press on the closed door to ensure it is securely in place. Second step: Inspect and clean the door seal Examine the sealing gasket around the door to ensure it is not damaged, deformed, or detached. Clean the gasket and contact surfaces with a damp cloth to remove any buildup of dirt or debris that could prevent a tight closure. Check that the gasket is properly positioned in its groove. Third step: Reset the device Completely turn off the microwave by pressing the switch or unplugging the device from the electrical outlet. Wait at least 2 to 3 minutes. Plug the microwave back in or turn it on again. Test the normal operation of the microwave. If the error code dE F2 reappears after these checks, it likely indicates a fault with the door sensor or a more serious issue with the locking system. In this case, it is recommended to contact an authorized FAR service technician, as these components require professional intervention. Do not attempt to repair the locking mechanism yourself, as this could affect the safety of the device.

Q: Does the FAR MOE25SB model have a filter to clean?

The FAR MOE25SB model is a countertop microwave and is not equipped with a filter to clean . Unlike range hoods that have grease or charcoal filters, this microwave has no regular maintenance filter. The maintenance of your oven is limited to the following elements: Oven cavity: Clean it after use with a slightly damp cloth. To facilitate cleaning, you can use the lemon trick: place half a lemon in a bowl with 300 ml of water and run the oven at 100% power for 10 minutes, then wipe with a dry cloth. Accessories: Clean them with soapy hot water or in the dishwasher. Door frame and seal: Clean them regularly with a damp cloth when they are dirty. Door glass: Never use abrasive cleaning products or metal scrapers, as this could scratch or crack the surface. Regular cleaning ensures optimal operation and extends the lifespan of your appliance.

Question 1

What is the duration of the intensive cotton program of the FAR LF510L23W?

Accepted Answer

On the FAR LF510L23W washing machine, the duration of the intensive cotton program varies according to the selected temperature:

Intensive Cotton 60°C: 3 hours 53 minutes
Intensive Cotton 40°C: 3 hours 48 minutes

This extended program is designed to enhance the washing effect and clean your textiles more deeply. The duration may vary slightly depending on the load and the type of fabric.

Question 2

How to drain the water from the FAR LF510L23W washing machine?

Accepted Answer

Here’s how to drain the water from your FAR LF510L23W:

Stop and unplug the machine, then make sure it has completed its washing cycle
Open the cap of the lower cover located at the bottom of the appliance
Turn the filter counterclockwise to access it
Let the water completely drain through the drain filter
Wait for the water to cool before handling the filter - risk of burns
Take the opportunity to clean the filter: remove any accumulated foreign materials
Close the lower cover after cleaning

Maintenance tip: Repeat this operation every 3 months to ensure the proper functioning of your machine.

Question 3

How to order spare parts for the FAR SLEE7MI18W washing machine?

Accepted Answer

To order spare parts for your FAR SLEE7MI18W dryer, several options are available to you. The most commonly replaced part is the lint filter, for which the compatible reference is MDS70 V032/A0431-EU18P1-Y1.

Specialized online retailers: Several websites offer original or compatible spare parts for this model. You can order from FixPart (fast delivery), Menager-Technic (specialist since 1982), PCDT, Sogedis, or Adepem. These retailers generally offer delivery within 24 to 48 hours.
FAR customer service: You can directly contact the customer service of the FAR brand to obtain a complete list of available parts and the exact references compatible with your SLEE7MI18W model. They can also recommend an authorized service center if you need installation.
Authorized retailers and centers: Authorized FAR repair centers usually have parts in stock. This option also allows you to benefit from professional advice on the part to be replaced.

Before ordering, note the exact reference of your appliance (SLEE7MI18W) and, if possible, precisely identify the part to be replaced. Refer to the user manual for specific references of other spare parts (motor, thermostat, etc.).

Maintenance tip: Clean the lint filter after each drying cycle to avoid premature replacements. A regularly maintained filter extends the lifespan of your dryer and optimizes its energy efficiency.

Question 4

How to activate and use the economy mode on the FAR FMO20?

Accepted Answer

The FAR FMO20 is not equipped with a distinct economy mode. However, you can significantly reduce its energy consumption by smartly using the 5 microwave power levels available on the Power control button, according to your needs.

For minimal energy consumption, opt for the lowest power levels:

17 % for softening ice
33 % for soup, stew, or defrosting
55 % for stews and fish
77 % for rice, fish, chicken, or minced meat
100 % for quick reheating, boiling water, vegetables, and drinks

Therefore, use the 17 %, 33 %, or 55 % levels as much as possible, as these levels consume less electrical power. Adjust the power by turning the Power knob to the desired value, then set the cooking time with the Timer button. The oven will start automatically.

Important: After each use, always set the timer to 0 to completely turn off the device; otherwise, it will remain unnecessarily active and consume energy.

Regular maintenance also helps to maintain optimal energy efficiency. Clean the interior after each use with a slightly damp cloth, and ensure that the door frame and seal are clean. A clean oven heats better and consumes less energy.

Question 5

Where is the washing filter located on the FAR LVC518DW dishwasher?

Accepted Answer

On the FAR LVC518DW dishwasher, the washing filter is an essential component to ensure proper filtration of food residues and guarantee effective washing. Here’s how to locate it:

Open the dishwasher door to access the inside of the drum.
Remove the bottom basket to get a better view of the bottom of the drum.
The washing filter is usually located at the center of the bottom of the drum, under the lower spray arm.
It consists of a coarse filter (plastic) and a fine filter (metal or fine mesh).

To access the filter, it is often enough to unscrew it or lift it depending on the model. Remember to clean this filter regularly to avoid clogs and maintain the performance of your dishwasher.

Warning: Before any handling, make sure the appliance is turned off and unplugged to avoid any electrical risk.

Question 6

How to set a delayed start on the FAR LV13C49M19IX dishwasher?

Accepted Answer

To set a delayed start on your FAR LV13C49M19IX dishwasher, follow these simple steps:

Steps to set the delayed start

Turn on the dishwasher by pressing the power button.
Select the desired wash program using the selection buttons.
Press the "Delay Start" button (depending on the indication on the control panel).
Set the delay using the + or - buttons to choose the number of hours after which the cycle should start (usually from 1 to 24 hours).
Confirm the programming by pressing the start button or "Start". The device will display the remaining time before the cycle begins.
Keep the door closed and do not unplug the device for the delayed programming to take effect.

This feature allows you to start the wash at a more convenient time, for example during off-peak hours to save energy.

Question 7

What cover should be removed to access the bulb on the FAR FMO20 microwave?

Accepted Answer

Important safety notice: Before any handling, completely unplug the FAR FMO20 microwave from its electrical outlet. The replacement of the lighting bulb should only be undertaken if you are comfortable with this operation, as it is strongly advised against for unqualified individuals to perform operations involving the removal of covers that protect against exposure to microwave energy.

On the FAR FMO20, the lighting bulb is located behind a viewing window (porthole) usually found on the top of the microwave, just behind the control panel. To access it, you need to remove a small plastic protective cover or porthole.

Access procedure:

Unplug the device from its power source (230 V) and wait a few minutes for all components to cool down.
Locate the porthole cover: look for a small translucent or opaque plastic plate, usually square or round, located on the top or on the right side of the microwave, near the control panel.
Unscrew or remove the cover that protects the lighting porthole. Depending on the model, it may be secured by one or two screws to be removed with an appropriate screwdriver (usually a flat screwdriver).
Access the bulb: once the cover is removed, you will see the lighting bulb. It is usually a pin or screw type, depending on your microwave version.

Replacement: If the bulb needs to be replaced, use a compatible replacement bulb for the FAR FMO20 (original type and wattage). Never use a higher wattage bulb, as it could damage the lighting system. After replacement, reinstall the cover and screws, tightening them lightly.

If you have difficulty locating the cover or are unsure about handling the device, contact FAR customer service or consult a qualified repair technician to perform this operation safely.

Question 8

What does the error code dE F2 mean on the FAR MOE30S microwave and how can it be resolved?

Accepted Answer

The error code dE F2 on the FAR MOE30S microwave indicates that the device has detected a problem with the door or its safety system. This code appears when the device cannot confirm that the door is properly closed, either because it is not closed correctly or due to a faulty door sensor.

First step: Check the door closure

Open the microwave door completely and check that no obstacles are preventing it from closing.
Close the door firmly until you hear a locking click. The door must be properly engaged.
Gently press on the closed door to ensure it is securely in place.

Second step: Inspect and clean the door seal

Examine the sealing gasket around the door to ensure it is not damaged, deformed, or detached.
Clean the gasket and contact surfaces with a damp cloth to remove any buildup of dirt or debris that could prevent a tight closure.
Check that the gasket is properly positioned in its groove.

Third step: Reset the device

Completely turn off the microwave by pressing the switch or unplugging the device from the electrical outlet.
Wait at least 2 to 3 minutes.
Plug the microwave back in or turn it on again.
Test the normal operation of the microwave.

If the error code dE F2 reappears after these checks, it likely indicates a fault with the door sensor or a more serious issue with the locking system. In this case, it is recommended to contact an authorized FAR service technician, as these components require professional intervention. Do not attempt to repair the locking mechanism yourself, as this could affect the safety of the device.

Question 9

How to cancel or modify the already programmed automatic option on the FAR MOG25X?

Accepted Answer

Your FAR MOG25X is a multifunction microwave-grill with a 25-liter internal capacity and has automatic programming functions. To cancel or modify an already ongoing automatic option, follow these simple steps:

To immediately stop an automatic cooking: Press the STOP/CANCEL button located on the control panel once. This immediately interrupts the ongoing cooking, regardless of the mode used (microwave, grill, or combined function). After a short pause, your device returns to its initial standby state.

To modify the settings of an active program: Once cooking has started, you can adjust the settings by pressing the available selection buttons to modify the power or remaining time. Depending on the activated mode (100% microwave, 80% grill + 20% microwave, etc.), you can adapt the settings without completely stopping the process.

To completely reset the device: If you want to cancel all programmed settings and start over, press STOP/CANCEL once to stop the cooking, then wait a few seconds. The FAR MOG25X automatically returns to standby mode, ready to receive new programming.

Important points: Remember to always set the timer to zero (0) after use to avoid accidental overheating of the magnetron. The FAR MOG25X operates at a voltage of 230V and offers 14 pre-programmed automatic programs for common cooking tasks (reheating, defrosting, cooking rice, chicken, etc.).

Question 10

Does the FAR MOE25SB model have a filter to clean?

Accepted Answer

The FAR MOE25SB model is a countertop microwave and is not equipped with a filter to clean. Unlike range hoods that have grease or charcoal filters, this microwave has no regular maintenance filter.

The maintenance of your oven is limited to the following elements:

Oven cavity: Clean it after use with a slightly damp cloth. To facilitate cleaning, you can use the lemon trick: place half a lemon in a bowl with 300 ml of water and run the oven at 100% power for 10 minutes, then wipe with a dry cloth.
Accessories: Clean them with soapy hot water or in the dishwasher.
Door frame and seal: Clean them regularly with a damp cloth when they are dirty.
Door glass: Never use abrasive cleaning products or metal scrapers, as this could scratch or crack the surface.

Regular cleaning ensures optimal operation and extends the lifespan of your appliance.

User manual FAR : user manuals and guides in PDF

Models FAR most viewed

Browse manuals FAR by appliance type

Recent questions about devices FAR