Q: How to roast peppers in a Create Fryer Air Pro Compact?

Although the manual for the Create Fryer Air Pro Compact does not provide a specific program for peppers, you can easily roast them using the manual settings. Recommended settings: Temperature: 200-210°C Time: 15-18 minutes (depending on the size of the pieces) Preparation: Lightly brush the peppers with oil before cooking for a nice browning This fryer offers a temperature range of 80°C to 220°C , allowing for great flexibility. To adapt your recipes, the manual recommends reducing the temperature by 10°C and the time by 30 to 50% compared to traditional recipes. Practical tips: Fill the basket no more than halfway - this ensures even air circulation Shake or turn the peppers halfway through cooking for even cooking Preheat for 3-5 minutes before starting the cooking Once cooking is complete, you will hear 10.5 beeps signaling the end of the program.

Q: How to install the decorative cover on the Create Wind Cup fan?

To install the decorative cover (lid) on your Create Wind Cup fan, follow these steps: Installation Steps Ensure that the connection plate is already attached to the fan. Place the decorative cover on the connection plate. Use a screwdriver to tighten the central screw that secures the cover to the fan housing. Tighten firmly but do not force. Important: This procedure applies to the NO LIGHT model. If you have a WITH LIGHT model, a magnetized LED panel attaches in place of the decorative cover, without requiring screws.

Q: How to connect and configure a wall controller to the Create Wind Cup fan?

Important: The official PDF manual for the Create Wind Cup does not mention a connection for a standard wall controller. This fan is not compatible with traditional electrical dimmers. Available control modes The Create Wind Cup fan is designed to operate exclusively with: Wireless infrared remote control (included) - power: 2 AAA batteries CREATE mobile app (Wi-Fi 2.4 GHz) Pairing the remote control If you need to reset or pair the remote control: Turn off the main switch for at least 10 seconds Turn on the switch and wait a maximum of 3 seconds Press and hold the power button until you hear a beep Wi-Fi connection (CREATE app) To control the fan via the mobile app: Install the CREATE app and create an account On the remote control, press and hold the 1H and 4H buttons for about 5 seconds until you hear a beep Confirm the pairing in the app Warning: Never use a dimmer with this fan. It could damage the motor and void the warranty. If you have a wall controller specifically created for Create, contact Create support for instructions.

Question 1

How to roast peppers in a Create Fryer Air Pro Compact?

Accepted Answer

Although the manual for the Create Fryer Air Pro Compact does not provide a specific program for peppers, you can easily roast them using the manual settings.

Recommended settings:

Temperature: 200-210°C
Time: 15-18 minutes (depending on the size of the pieces)
Preparation: Lightly brush the peppers with oil before cooking for a nice browning

This fryer offers a temperature range of 80°C to 220°C, allowing for great flexibility. To adapt your recipes, the manual recommends reducing the temperature by 10°C and the time by 30 to 50% compared to traditional recipes.

Practical tips:

Fill the basket no more than halfway - this ensures even air circulation
Shake or turn the peppers halfway through cooking for even cooking
Preheat for 3-5 minutes before starting the cooking

Once cooking is complete, you will hear 10.5 beeps signaling the end of the program.

Question 2

After installing a new LED kit for my WIND CALM fan with old wiring, the remote control no longer responds to control the light. What should I do?

Accepted Answer

This problem usually occurs when replacing a LED kit with a different model or when improperly reusing old wires. Here’s how to diagnose and resolve:

Step 1 - Check the blue and white wires

The LED kit provided by Create includes specific blue and white wires for connecting the light. If you reused the old wires instead of using the new ones provided, the remote control will not be able to control the light. You must replace them with the original wires from the new kit.

Step 2 - Check the LED panel assembly

According to the WIND CALM documentation, the plugs must be connected to the pins at the bottom of the basket and the LED panel. Check that:

The magnetized LED panel is properly secured in place
The decorative screen is well placed over the panel
The connections are not loose

Step 3 - Check the grounding

A common issue with the WIND CALM: a faulty grounding affects light performance, including responsiveness to the remote control. Ensure that the ground wire (green/yellow) is properly connected:

Check that the green/yellow wire is properly connected
Test continuity with a multimeter if possible

Step 4 - Compatibility of LED kits

The LED kit compatible with WIND CALM, WIND CALM NATURAL WOOD, WIND RATTAN, and WIND LITE shares the same basic interface. However, some older versions included a built-in dimmer, while newer versions manage remote control. If the new kit does not include the appropriate wires or clear documentation, contact Create directly for the missing parts.

Summary

To try first: Use the blue and white wires provided with the new kit (not the old ones). Check that the LED panel is magnetized correctly and that the grounding is established. If the remote control remains unresponsive, there may be an incompatibility between the versions of the kit - create a support request with Create mentioning the exact references of both kits.

Question 3

How to install the decorative cover on the Create Wind Cup fan?

Accepted Answer

To install the decorative cover (lid) on your Create Wind Cup fan, follow these steps:

Installation Steps

Ensure that the connection plate is already attached to the fan.
Place the decorative cover on the connection plate.
Use a screwdriver to tighten the central screw that secures the cover to the fan housing. Tighten firmly but do not force.

Important: This procedure applies to the NO LIGHT model. If you have a WITH LIGHT model, a magnetized LED panel attaches in place of the decorative cover, without requiring screws.

Question 4

Where can I find the complete assembly manual for the Create WIND STYLANCE?

Accepted Answer

The complete assembly manual for the Create WIND STYLANCE is available in full on this page, in a 88-page PDF format.

Main sections of the guide:

Parts list: Check for the presence of the LED panel, decorative screen, mounting screws, anti-sway kit with clips and adhesive counterweights, AAA remote control, and the suspension rod (15 or 25 cm)
Before assembly: Location requirements (minimum height 2.3 meters from the ground, minimum obstacle distance 50 cm)
Installation of the mounting bracket: Ceiling attachment
Mounting and suspending the fan: Suspension and assembly steps
Electrician tips: Connection to the power supply 220-240 V ~ 50 Hz
Remote control functions: The 8 buttons (Light, On/Off, Timer, Temperature, Intensity, Reverse function, Mute)

Check the PDF viewer at the top of this page to directly access the steps you need. You can also download it to print or view offline.

Question 5

How to connect and configure a wall controller to the Create Wind Cup fan?

Accepted Answer

Important: The official PDF manual for the Create Wind Cup does not mention a connection for a standard wall controller. This fan is not compatible with traditional electrical dimmers.

Available control modes

The Create Wind Cup fan is designed to operate exclusively with:

Wireless infrared remote control (included) - power: 2 AAA batteries
CREATE mobile app (Wi-Fi 2.4 GHz)

Pairing the remote control

If you need to reset or pair the remote control:

Turn off the main switch for at least 10 seconds
Turn on the switch and wait a maximum of 3 seconds
Press and hold the power button until you hear a beep

Wi-Fi connection (CREATE app)

To control the fan via the mobile app:

Install the CREATE app and create an account
On the remote control, press and hold the 1H and 4H buttons for about 5 seconds until you hear a beep
Confirm the pairing in the app

Warning: Never use a dimmer with this fan. It could damage the motor and void the warranty. If you have a wall controller specifically created for Create, contact Create support for instructions.

Question 6

How to adjust and control the LED light of the Create Wind Calm?

Accepted Answer

The Create Wind Calm fan with LED light features a complete control system via remote control. Here’s how to use the lighting functions:

Turning the light on and off

Press the Light button on the remote control to turn the LED light on or off.

Adjusting the brightness

Use the brightness control button to increase or decrease the brightness according to your preferences. You can adjust it gradually from minimum to maximum.

Changing the color temperature

Press the color temperature control button on the remote control to switch between the three available modes:

Warm white
Neutral white
Cool white

Important: Ensure that the ground wire is properly connected. A faulty ground connection may cause the lights to dim or flicker.

Question 7

How to contact Create's technical service for the WIND HELIX?

Accepted Answer

The WIND HELIX manual does not mention specific contact details for Create's technical service. Here’s how to obtain them:

Check the paper documentation - The box, the complete manual, or the warranty card usually contain a phone number or an email address for after-sales support.
Visit Create's official website - Look for the manufacturer's site for your region (Create offers country-specific variants). You will find a contact form or a support number there.
Contact your retailer - If you purchased the fan recently, the store or sales website may assist you with warranty claims.
Check the warranty information - For warranty issues on the WIND HELIX (motor, electronics, LED), support details are usually on the warranty document provided with the product.

Question 8

The remote control for the Create WIND HELIX is not working after an attempt to resynchronize - how can I fix it?

Accepted Answer

If your Create WIND HELIX remote control is not working even after an attempt to resynchronize, follow these troubleshooting steps:

First, check the batteries

The remote control uses 2 AAA batteries. The batteries may be worn out even if they seem to work. Replace them with new batteries and test the remote control.

Complete re-pairing of the remote control

If replacing the batteries does not solve the problem, re-pair the remote control by following this procedure:

Turn off the main switch of the fan for at least 10 seconds
Turn the switch back on - you will hear a beep confirming activation
Within the next 3 seconds, press and hold the on/off button until you hear a second beep
The remote control is then re-paired

If re-pairing fails

Repeat the procedure by leaving the main switch off for at least 1 minute this time, then start the steps above again.

Important note: Only use official remotes approved by Create. Using an unauthorized remote will void the fan's warranty.

Question 9

How do I connect all the elements of the Create Wind Calm (fan, mount, LED kit) to the ground?

Accepted Answer

The correct grounding of your Create Wind Calm is essential for safety and proper functioning. According to the manual, the fan, the mounting bracket, and the lighting kit must all be grounded (page 37).

Wiring Diagram

The manual provides two detailed diagrams:

Model with LED light (page 39): The ground wire (green/yellow stripe) connects to the ground terminal of the receiver. The L (black - phase) and N (white - neutral) inputs power the system. The LED circuit uses the blue wire, while the motor uses the gray, pink, and red wires for the three speeds.
Model without LED (page 42): Same principle with the green/yellow stripe for ground and the L/N inputs. The motor still uses the three wires (gray, pink, red).

Critical Point

⚠️ Warning: The manual states that "if the ground wire is not connected properly, the lights may dim or flicker" (page 44). This helps diagnose poor grounding.

Compliance with Standards

Important: All wiring must comply with national and local electrical codes and the ANSI/NFPA 70 standard (page 37). We strongly recommend having the installation done by a qualified electrician to ensure compliance and your safety.

Question 10

How to pair the remote control with the Create WIND MINIMAL fan?

Accepted Answer

Here is the pairing procedure for the remote control with your Create WIND MINIMAL fan:

Pairing Steps

Power Cut: Turn off the main switch in the room where you installed your fan for at least 10 seconds.
Power On: Turn the switch back on. You will hear a beep within the next 3 seconds.
Activate the Remote Control: Press and hold the on/off button on the remote until you hear a second beep.
Confirmation: Pairing is successful - your remote now controls the fan.

In Case of Failure

If pairing does not work, cut the power for at least a full minute, then repeat the entire procedure above.

Before You Start

Make sure your remote control is equipped with 2 new AAA batteries that are correctly installed.

Main Buttons on Your Remote Control

On/Off: Overall control of the fan
Fan Speed: Adjusts among the 3 available speeds
Reverse Function: Switches between summer mode (counterclockwise rotation) and winter mode (clockwise rotation)
Light: Turns the LED lighting on/off independently
Timer: Programs the automatic shut-off
Color Temperature: Selects among 3 modes (3000K, 4000K, 6500K)
Sound Deactivation: Mutes the remote beeps

Remote Control Range: 10 meters

User manual Create : user manuals and guides in PDF

Models Create most viewed

Browse manuals Create by appliance type

Recent questions about devices Create