Q: Should I lubricate the chuck of the AEG SB2-700 drill?

No, you should not lubricate the chuck. The AEG manual explicitly recommends against greasing the chuck, as it would attract abrasive dust that could damage the clamping mechanism. Recommended maintenance for the chuck: Use the cleaning spray reference 4932 6217 19 on the jaws and clamping holes for optimal cleaning. For regular cleaning without product: hold the drill vertically (chuck down), then loosen and tighten the chuck fully several times. The accumulated dust will fall off naturally. If the drill is frequently used in hammer mode, clean the chuck at regular intervals. Have the motor brushes checked once a year by an AEG service center.

Q: What does the flashing green light on the AEG POWERBASE 60 charger mean?

The flashing green light on your AEG POWERBASE 60 charger indicates a specific condition related to the battery status. According to the official manual, this light can have three different meanings: Solid green light: Fast charging is proceeding normally (temperature between 0°C and 45°C). Flashing green light: The battery is either too hot, too cold, or fully charged in maintenance charge mode. Battery too hot (above 45°C): When the light flashes for this reason, the charger automatically switches to maintenance charge mode to protect the battery. Remove it from the charger and allow it to cool naturally to room temperature until it drops below 45°C. Then reinsert it into the charger: normal charging will automatically resume. Battery too cold (below 0°C): If the battery is too cold, no charging occurs initially. Simply leave the battery in the charger: it will gradually warm up due to maintenance charge mode, and charging will automatically restart without any action required from you. Battery fully charged: Once charging is complete (usually between 10 and 60 minutes depending on the 1.4 Ah capacity), the charger switches to maintenance charge mode, indicated by the flashing light. In this state, the battery maintains its maximum capacity and can remain connected to the charger indefinitely without risk of overcharging. You can therefore leave your AEG POWERBASE 60 battery in the charger permanently, ensuring it is always ready for use.

Question 1

How to replace the carbon brushes of the AEG SB2E 680 R electric drill?

Accepted Answer

Replacing the carbon brushes (wear parts) of your AEG SB2E 680 R drill is not intended as a user maintenance intervention. This operation must be carried out by an authorized AEG service center.

Scheduled Maintenance

Recommended annual inspection: The manual recommends having the brushes checked once a year by an AEG service center to ensure the continuous proper functioning of the device.
Replacement by a professional: If the inspection determines that the brushes are worn, the replacement will be carried out by the AEG service center.
Original parts only: You must use only original AEG replacement parts.

To obtain an inspection or replacement of brushes, contact an AEG service center in your area. The service can also provide you with a breakdown diagram of the device if you need it.

Question 2

How to turn or reverse the knife of the AEG H 500 planer?

Accepted Answer

The knife of your AEG H 500 can be turned (reversed) when one side wears out. Here’s how to proceed:

Before you begin

Turn off the power: unplug the plug from the socket (mandatory safety)
The knives must always be changed in complete pairs, never one at a time

Reversal procedure

Operate the lever of the protective cover and hold it in the open position
Loosen the screws (F) by turning to the right
Press the knife holder's protective cover (E) down and laterally remove the tension element (D) with the knives
Clean the tension element and the knife holder (B)
Insert the reversed knives laterally and flush into the tension element, ensuring that the cam engages in the groove
Slide the tension element to align the knife edge with the casing (G)
Press the tension element and tighten the screws (F) to the left
Shift the shaft and repeat the operation for the second set of knives

Important points

Check that the knife does not rub against the casing after reinstallation
Do not modify the screws (H): they are factory adjusted
Once both sides are worn after reversal, replace the knives with an original AEG H 500 pair

Question 3

Should I lubricate the chuck of the AEG SB2-700 drill?

Accepted Answer

No, you should not lubricate the chuck. The AEG manual explicitly recommends against greasing the chuck, as it would attract abrasive dust that could damage the clamping mechanism.

Recommended maintenance for the chuck:

Use the cleaning spray reference 4932 6217 19 on the jaws and clamping holes for optimal cleaning.
For regular cleaning without product: hold the drill vertically (chuck down), then loosen and tighten the chuck fully several times. The accumulated dust will fall off naturally.
If the drill is frequently used in hammer mode, clean the chuck at regular intervals.
Have the motor brushes checked once a year by an AEG service center.

Question 4

How to clean the chuck of the AEG SB2-700 drill?

Accepted Answer

To clean the chuck of your AEG SB2-700 drill, you have two methods:

Basic Cleaning

Hold the machine in a vertical position, with the chuck facing down, then loosen and tighten the chuck as much as possible. The accumulated dust will naturally fall from the chuck.

Deep Cleaning

For optimal maintenance, use the cleaning spray reference 4932 6217 19 from AEG directly on the clamping jaws and their bores. This specific product is particularly effective if you regularly use your drill in hammer mode, as dust accumulates more in the chuck.

Important

Never lubricate the chuck with greasy oil. This would attract abrasive dust that damages the clamping mechanism. For complete maintenance, AEG also recommends having the motor brushes checked once a year by the after-sales service.

Question 5

How to unlock the percussion mode selector that is stuck

Accepted Answer

The mode selector of your AEG SB2E 700 RS drill allows you to switch between normal drilling and percussion. Before any intervention, turn off the drill and unplug it from the socket.

To unlock the stuck selector, start by visually inspecting it. If you see dust, mud, or debris around the selector, gently clean this area with a dry, clean cloth. Avoid using water or chemicals that could damage the internal mechanism.

Next, try to turn the selector gradually in both directions to free it. Never force it abruptly, as you risk breaking the mechanism. Firm but gradual pressure should be sufficient. If you feel slight resistance, that’s normal; continue gently.

Turn the selector to the left (percussion position) to drill stone with percussion
Turn the selector to the right (drilling position) to drill metal, plastic, wood, or to screw

Important: always change the position of the selector when the drill is stopped or idling (speed 1 or 2), never while in full operation. This rule prevents damage to the selector during use.

If the selector remains stuck after several attempts to unlock it, the problem may be internal. In this case, contact an authorized AEG service center for professional repair. Do not attempt to disassemble the drill yourself, as you could damage its safety system.

Question 6

What does the flashing green light on the AEG POWERBASE 60 charger mean?

Accepted Answer

The flashing green light on your AEG POWERBASE 60 charger indicates a specific condition related to the battery status. According to the official manual, this light can have three different meanings:

Solid green light: Fast charging is proceeding normally (temperature between 0°C and 45°C).
Flashing green light: The battery is either too hot, too cold, or fully charged in maintenance charge mode.

Battery too hot (above 45°C): When the light flashes for this reason, the charger automatically switches to maintenance charge mode to protect the battery. Remove it from the charger and allow it to cool naturally to room temperature until it drops below 45°C. Then reinsert it into the charger: normal charging will automatically resume.

Battery too cold (below 0°C): If the battery is too cold, no charging occurs initially. Simply leave the battery in the charger: it will gradually warm up due to maintenance charge mode, and charging will automatically restart without any action required from you.

Battery fully charged: Once charging is complete (usually between 10 and 60 minutes depending on the 1.4 Ah capacity), the charger switches to maintenance charge mode, indicated by the flashing light. In this state, the battery maintains its maximum capacity and can remain connected to the charger indefinitely without risk of overcharging. You can therefore leave your AEG POWERBASE 60 battery in the charger permanently, ensuring it is always ready for use.

Question 7

How to clean and maintain the AEG SB2E 680 R electric drill?

Accepted Answer

To keep your AEG SB2E 680 R electric drill in good working condition and extend its lifespan, regular and careful maintenance is essential. The key elements to follow will allow your machine to remain efficient for many years.

Before any intervention, always unplug the drill from the power outlet to avoid any risk of electric shock or accidental start-up. This safety rule is crucial for all maintenance work.

Cleaning the ventilation openings: Always keep the ventilation openings of the motor section clean and clear. Dust that accumulates on these openings reduces the cooling efficiency of the motor. Use a dry cloth or a soft brush to regularly dust the outer surface and ventilation slots. For hard-to-reach areas, a soft brush or a small vacuum cleaner is recommended.

Chuck maintenance in case of frequent percussion use: If your drill is often used in percussion mode, regularly remove the accumulated dust from the chuck. Hold the machine in a vertical position, with the chuck facing down, then loosen and tighten the chuck fully several times. All the accumulated dust will naturally fall out of the chuck. Then, apply the specific cleaning spray (reference AEG 4932 6217 19) on the jaws and the holes of the chuck jaws to ensure optimal operation. This application improves clamping performance and prevents corrosion.

General cleaning and accessories: Wipe the body of the drill with a slightly damp cloth to remove work dust and residues. Avoid immersing the machine or wetting the electrical connectors and ventilation openings. The drill bits and screwdriver bits can be cleaned separately with warm soapy water, then rinsed and dried completely.

Annual maintenance: It is recommended to have the wear of the motor brushes inspected once a year by an authorized AEG service center. This preventive inspection detects wear before it affects performance. Only use original AEG parts and accessories for all maintenance or repair work.

Question 8

Can the AEG SB2E 680 R electric drill drill into concrete?

Accepted Answer

Yes, the AEG SB2E 680 R electric drill can drill into concrete, provided that you use the appropriate accessories.

Tips for drilling into concrete with the AEG SB2E 680 R:

Use a suitable drill bit: Choose a concrete drill bit or a hammer drill bit specifically designed for hard materials like concrete.
Hammer mode: If the drill is equipped with a hammer function, activate it to facilitate drilling into concrete.
Speed adjustment: Adjust the drilling speed according to the hardness of the material; generally, a medium to low speed is recommended for concrete.
Gradual pressure: Start drilling slowly to avoid damaging the drill bit or the drill, then gradually increase the pressure.
Safety: Wear protective glasses and a dust mask to protect yourself while drilling.

By following these recommendations, you will be able to effectively use your AEG SB2E 680 R to drill into concrete.

Question 9

How do I open the cover of the AEG SB2-700 drill? Is there a hidden screw to remove?

Accepted Answer

To open the cover of your AEG SB2-700 electric drill, it is important to check for any hidden screws or clips that may hold the cover in place. Here are some tips to proceed:

1. Look for hidden screws

Carefully examine the entire perimeter of the cover. Some screws may be hidden under stickers, rubber caps, or decorative elements.
Use a flashlight to better see hard-to-reach areas.

2. Identify the fastening clips

If no screws are visible, the cover may be secured by plastic clips. Gently insert a flat tool, such as a thin screwdriver or spatula, between the cover and the body of the drill.
Leverage gently to release the clips without forcing to avoid damaging the plastic.

3. Precautions to take

Never force too much to avoid breaking the cover or internal components.
If you cannot open the cover, it is recommended to consult a qualified professional to avoid any damage.

By following these steps, you should be able to safely access the inside of your AEG SB2-700 drill.

Question 10

How to change the chuck of the AEG SB2E 750 R drill?

Accepted Answer

To change the chuck of your AEG SB2E 750 R drill, follow these simple steps:

1. Safety first

Make sure the device is unplugged or the battery is removed to avoid any accidental start.

2. Removing the current chuck

Keyless chuck: Firmly hold the chuck and turn it counterclockwise to unscrew it.
Chuck with key: Insert the provided key into the holes of the chuck, then turn it counterclockwise to unscrew it.

3. Installing the new chuck

Align the new chuck on the drill's shaft.
Screw it clockwise until it is securely fastened.
For a keyless chuck, ensure it is tightly secured to hold the bits in place.

4. Final check

Before plugging back in or reinserting the battery, check that the chuck is securely fastened and does not move.

Once these steps are completed, your drill is ready to use with the new chuck.

User manual AEG Drill : user manuals and guides in PDF

Models AEG Drill most viewed

Other categories AEG

Recent questions about Drill AEG