Question 1

How to clean the inner glass of the FAGOR HP-7660 electric oven door?

Accepted Answer

To clean the inner glass of your FAGOR HP-7660 electric oven door, here are the recommended methods:

1. Cleaning with door disassembly

If you can disassemble the door, it makes access to the inner glass easier:

Remove the door by following the model-specific instructions (usually by opening the door to 45° and unclipping the hinges).
Prepare a baking soda paste: mix 3 parts water with 1 part baking soda.
Apply the paste to the inner glass and let it sit for about 15 minutes.
Gently scrub with a non-abrasive sponge to remove residues.
Rinse and dry before reassembling the door.
You can also use a diluted ammonia solution in hot water for a deeper clean.

2. Cleaning without disassembly

If you do not wish to disassemble the door:

Use a damp cloth with a little mild detergent.
Avoid steam or high-pressure cleaners that could damage the seal or components.
Gently scrub to avoid scratching the glass.

3. Using the pyrolysis function

The FAGOR HP-7660 oven has a pyrolysis function that automatically cleans the inside of the oven by burning away residues. After a pyrolysis cycle:

Use a damp cloth to remove the fine white ash remaining on the glass.
This method is effective for general cleaning but does not always replace a manual cleaning of the inner glass of the door.

By following these tips, you can keep the inner glass of your oven door clean and in good condition, ensuring good visibility and optimal operation.

Question 2

How to tighten a loose door handle on the FAGOR 6H755A B electric oven?

Accepted Answer

Before any intervention, make sure to disconnect your FAGOR 6H755A B oven from its power supply to avoid any risk of electric shock. Wait for the appliance to cool down completely.

The handle of your oven is generally secured by screws located inside the door, accessible by partially removing the inner glass panel. Here is the procedure to follow:

Open the door fully: Open the oven door as much as possible to access the inside of its structure.
Locate the securing screws: Inside the door, you will find screws that hold the handle, usually located above or below the outer glass panel, near the fixing areas.
Access the screws: Depending on your model, you may need to carefully remove the frame or support of the inner glass. Look for small metal or plastic supports that hold this glass in place.
Tighten the screws: Using an appropriate Phillips or flat screwdriver (depending on the type of screws), gently turn them clockwise. Do not overtighten to avoid damaging them or breaking the plastic.
Test the sturdiness: Before completely closing, test the handle by pulling it gently to check that the tension is correct and that it does not move anymore.

Important: If the screws are inaccessible or if you notice visible damage to the handle or its fixing mechanism, it is recommended to contact an authorized FAGOR after-sales service. Forcing access could damage the thermal door and compromise the oven's sealing.

Question 3

How to identify and use the faded buttons on a FAGOR 2HF-11E electric oven?

Accepted Answer

When the buttons on your FAGOR 2HF-11E electric oven are faded, it can be difficult to know which function corresponds to each button and in what order to use them. Here are some practical tips to help you:

1. Identify the functions of the buttons

The buttons on a standard electric oven typically include: the cooking mode selector (convection, grill, etc.), the temperature setting, and the timer or cooking duration.
Try to spot physical clues on the buttons, such as their size, position, or resistance to rotation, which can differentiate their function.
If you still have the manual or can find an image of the control panel online, this can help you associate each button with its function.

2. Typical order of use

Generally, start by selecting the cooking mode with the first button.
Then set the desired temperature with the second button.
Finally, if your oven is equipped with one, set the timer with the third button.

3. Test the buttons carefully

Turn each button slowly and observe the oven's reactions: a light turning on, a fan starting, heating activation, or a display on a screen.
Note the effects to better memorize the function of each button.

4. Temporary marking to facilitate use

Once the functions are identified, you can use stickers, tape, or a permanent marker to clearly indicate the function of each button.
This will prevent any confusion during future use.

These steps will allow you to use your oven despite the faded buttons and avoid operational errors.

Question 4

How to use the dough rising function on the FAGOR 6H876ATCX electric oven when the minimum adjustable temperature is 120°C?

Accepted Answer

The FAGOR 6H876ATCX electric oven offers a minimum temperature of 120 °C, which may seem too high for dough rising, which generally requires a lower temperature and a humid environment. Here are some tips to successfully rise dough despite this constraint:

Create a suitable environment for dough rising

Preheat then turn off the oven: Turn on the oven to 120 °C for a few minutes, then turn it off. Keep the oven door closed to retain residual heat, which will be lower than 120 °C and more suitable for rising.
Maintain humidity: Place a container with hot water in the turned-off oven with the dough. The steam creates a humid environment favorable for rising.
Temperature control: Use an oven thermometer to check that the internal temperature drops to around 30-40 °C, ideal for dough rising.

Other tips

If your oven has a special "rising" or "fermentation" function, use it.
Otherwise, you can also place the dough in a warm spot in the kitchen, such as near a radiator or in a turned-off oven with the light on.

In summary, even if the minimum adjustable temperature is 120 °C, it is possible to create a suitable environment for rising by using residual heat and humidity in the turned-off oven.

Question 5

How can I find out the age of my FAGOR oven model 5H-741?

Accepted Answer

To determine the age of your FAGOR oven model 5H-741, you need to start by locating the appliance's nameplate, which contains the serial number. On this model, the nameplate is usually found inside the door frame of the oven (check under the top panel or on the side), or at the back of the appliance. The nameplate includes the model number, serial number, and other technical information.

Decoding the serial number: The FAGOR serial number contains manufacturing information. The first digits of the serial number typically indicate the year and week of manufacture. For example, if your serial number starts with the digits "0524", this could mean it was manufactured in 2005, week 24. For precise decoding specific to FAGOR, you can use online decoding tools like Much2.com or Decode My Item by entering your exact serial number.

Direct contact with FAGOR service: If you have trouble interpreting the serial number or locating the nameplate, FAGOR customer service (whose contact details are at the end of your manual) can help you accurately identify the manufacturing date from the serial number. Note that this model 5H-741 is from the early 2000s, and is therefore an appliance that is already over 20 years old.

Knowing the age of your FAGOR 5H-741 oven will be useful for assessing its overall condition, planning appropriate maintenance, checking if specific spare parts for this generation are still available, or for administrative or resale purposes.

Question 6

How to set the time on a FAGOR 6H220X electric oven?

Accepted Answer

To set the time on your FAGOR 6H220X electric oven, follow these simple steps:

Turn on the oven ensuring it is powered on.
Locate the "Clock" button on the control panel. On this model, it is usually identifiable by a clock icon or the word "Time".
Press this button to access the time setting mode.
Set the time using the " + " and " - " buttons or the arrows to scroll through the numbers until the correct time is displayed.
Confirm the setting by pressing the "OK", "Validate" button or by pressing the "Clock" button again depending on the model.
Check that the time is displayed correctly on the oven's screen.

This setting allows you to use the oven's programmed functions with the correct time, including timers and delayed starts.

Question 7

How to unlock the door of the FAGOR oven model 5H-741?

Accepted Answer

The FAGOR 5H-741 oven is equipped with an automatic door locking system for safety reasons. Unlike some ovens, this model does not have a manual unlock button. The locking mechanism is activated automatically when the oven is in use or during cleaning cycles.

To unlock the door, start by turning off the oven and completely shutting down the appliance. Once the oven is off, wait a few minutes for the internal temperature to decrease. The locking system will deactivate automatically once the oven has cooled down sufficiently. You can check the lock status by looking at the programmer display: a padlock symbol indicates that the door is locked. When this symbol disappears from the screen, you can open the door.

It is particularly important to understand that during a pyrolysis cycle (self-cleaning), the door remains locked for your safety as the oven reaches very high temperatures. This safety lock is normal and cannot be bypassed: simply wait for the cycle to finish and for the oven to cool completely before attempting to open the door.

Once the door is unlocked, gently open it by gradually pulling on the handle. Never use excessive force, as this could damage the locking mechanism or the oven's sealing gaskets.

If the door remains locked after several hours of complete cooling or if you encounter an error message "Er: V" on the display (this message indicates a fault in the locking system), it is a technical issue. In this case, consult FAGOR customer service, as only a qualified professional can intervene on the locking system safely.

Question 8

How to set the time on the FAGOR 6H210AB electric oven?

Accepted Answer

Your FAGOR 6H210AB electric oven has a digital clock that requires initial setting to complete the installation. Here’s how to proceed:

Setting Steps:

Use the + and - buttons to adjust the desired time (hours and minutes).

Important to remember: After a power outage or when changing the time (switching to daylight saving time or standard time), you will need to set the time again following the same procedure. The clock does not retain settings in case of a power interruption.

If you see the (©) button blinking while using the oven, it means the time needs to be adjusted. Follow the steps above and your oven will operate normally.

Question 9

How to reattach the door of the FAGOR 6H185A N oven?

Accepted Answer

To reattach the door of your FAGOR 6H185A N oven, follow these simple steps:

Steps to replace the oven door

Preparation: Ensure that the oven is turned off and cold before handling to avoid any risk of burns.
Hinge alignment: Check that the door hinges are properly aligned with the designated spots on the oven.
Positioning: Slightly tilt the door upwards and insert the hinges into their respective slots on the oven.
Full insertion: Slide the door down until the hinges are fully engaged and the door is stable.
Verification: Open and close the door several times to ensure it is securely attached and operates normally.

If the door does not reattach easily, check that no parts are damaged or warped. If in doubt, it may be helpful to contact a professional to avoid damaging the oven.

Question 10

How to find a replacement glass for a FAGOR Innovation Class A oven model 5H-721N4?

Accepted Answer

To find a replacement glass for your FAGOR Innovation Class A oven model 5H-721N4, you first need to accurately identify the type of glass you need. There are two distinct elements: the door glass (triple glazing) which is the main glass of the oven, and the small glass for the bulb for the interior lighting located at the ceiling of the oven cavity.

For the small bulb glass (also called socket + lamp glass), the spare part reference is 74X2659. This element includes the bulb holder and its protective cover. This part is compatible with several brands: FAGOR, BRANDT, DE DIETRICH, SAUTER, ROSIERES, TELEFUNKEN, and others. You can order this part directly from specialized suppliers of spare parts.

To obtain the parts, contact one of these French suppliers specialized in FAGOR appliance spare parts: Sogedis, Spareka, SOS-Accessoire, or Menager-Technic (distributor since 1982). These companies generally offer a catalog with exploded diagrams allowing you to accurately identify each part of your model 5H-721N4. Visit their website directly and search for your exact model number.

The recommended process is as follows: first, note the complete serial number inscribed on your oven (5H-721N4), then contact one of these suppliers by phone or via their online contact form with this number, and request a quote before ordering. If you need technical advice to identify whether it is indeed the small bulb glass or the large door glazing that needs to be replaced, these suppliers can assist you via video conference or by phone.

You can also contact FAGOR customer service directly by mentioning your model number 5H-721N4. Delivery times generally vary between 3 and 7 days depending on the supplier and the availability of the part. Before ordering, make sure the supplier confirms compatibility with your exact variant of the model.

User manual FAGOR Electric oven : user manuals and guides in PDF

Models FAGOR Electric oven most viewed

Other categories FAGOR

Recent questions about Electric oven FAGOR