10500 - Pump GARDENA - Free user manual and instructions

Product Type	Drainage pump for dirty water
Brand	Gardena
Model	10500 (Ref. 9008)
Nominal power	400 W
Supply voltage	230 V AC, 50 Hz
Max. flow rate	10,500 l/h
Max. pressure / Max. delivery head	0.5 bar / 5.0 m
Max. immersion depth	6 m
Min. operational immersion depth	50 cm
Residual water height	25 mm
Max. particle diameter	25 mm
Max. liquid temperature	35 °C
Weight (without cable)	Approx. 2.9 kg
Power cable length	10 m (H05RN-F)
Float switch type	Adjustable float (on/off level)
Operating mode	Automatic (with float) and manual
Protection	Thermal safety cut-out, recommended RCD (30 mA)
Material	Not specified, but waterproof submersible
Use	Flood drainage, tank emptying, wells, chlorinated water (temporary)
Maintenance	Rinse after chlorinated water, clean suction foot and impeller
Wear parts	Impeller (excluded from warranty)
Included accessories	Elbow piece, connection nozzle (25 mm and 38 mm)
Warranty	2 years (wear parts excluded)

Frequently Asked Questions - 10500 GARDENA

How to start the Gardena 10500 pump?

Immerse the pump in water, plug it into a socket protected by an RCD. The pump starts immediately. Use the float for automatic shut-off in the absence of water.

Why is my pump not discharging water?

Check that the discharge hose is not closed, there is no air lock (wait 60 seconds), the suction opening is not blocked, and the impeller is not jammed. Clean if necessary.

What type of water can I pump with the Gardena 10500?

The pump can handle clear to slightly dirty water with particles up to 25 mm in diameter (dirty water). Do not pump salt water, flammable liquids, or oils.

How to adjust the float for automatic mode?

The float must float freely. To change the on/off levels, press the float cable into the provided clip. The shorter the cable, the lower the start level and the higher the stop level. Leave at least 10 cm of free cable.

Can I use the pump in manual mode?

Yes, slide the float down onto the clip to bridge it. Note that the pump will run continuously. The minimum residual water level is only achieved in manual mode.

How to maintain the pump after pumping chlorinated water?

Rinse the pump by pumping warm water (max. 35 °C) with a mild detergent like dish soap until the discharged water is clear.

How to store the pump in winter?

Disconnect the pump, drain it by placing it on its head, clean it, and store it in a dry, frost-free place. The pump is not frost-resistant.

What to do if the pump stops during operation?

This may be due to overheating (thermal cut-out triggered), power supply fault, or RCD tripping. Allow the pump to cool down or check the fuses.

What accessories are available for the Gardena 10500?

Hose clips for 25 mm (ref. 7193) and 38 mm (ref. 7195) hoses, a pump connection kit for 19 mm hose (ref. 1752), and a 10 m flat hose kit (ref. 5005).

Can the pump run dry?

No, the pump must not run dry. Use the float to stop it automatically in the absence of water. Do not let the pump run for more than 10 minutes with the discharge closed.

USER MANUAL 10500 GARDENA

Line drawing of a portable vacuum cleaner with attached tubing and control panel (no text or symbols)

8200

Art. 9000

8600

Art. 9001

Likaveden uppopumppu

NO Bruksanvisning

Nedsenkbarrentvannspumpe/

Line drawing of a portable water purifier with attached tubing and control panel (no text or symbols)

9200

Art. 9007

10500

Art. 9008

SK Návod na obsluhu

Original instructions.

This product may be used under supervision, or if instruction regarding the safe use of the product has been provided and the resulting dangers have been understood, by children aged 8 and above, as well as by persons with physical, sensory or mental disabilities or a lack of experience and knowledge. Children must not be allowed to play with the product. Cleaning and user maintenance must not be performed by children without supervision. The use of this product by young people under the age of 16 is not recommended. Never operate the product when you are tired, ill or under the influence of alcohol, drugs or medicine.

1. SAFETY

Intended use:

The GARDENA Submersible Pump is intended for drainage purposes if flooding occurs but also for transferring water to and from tanks and pumping them out, for drawing water from wells and shafts, for draining boats and yachts and for aerating and circulating water for limited periods and for pumping chlorinated water in private domestic gardens and allotments.

Liquids to be pumped:

The GARDENA Submersible Pump must only be used to pump water.

The pump is fully submersible (water-tight encapsulation) and is submerged in water (for max. submersion depth, see 7. TECHNICAL DATA).

The product is suitable for pumping the following liquids:

• Clear Water Submersible Pump: clean to slightly dirty water with a max. particle size of 5 mm.
• Dirty Water Submersible Pump: dirty water with a max. particle size of 25 mm.

The product is not intended for long term use (continuous circulationoperation).

IGER! Risk of injury!

→ The pump should not be used for the delivery of salt water, corrosive, easily inflammable or explosive liquids (e.g. petrol, paraffin, thinners), oil, heating oil or foodstuffs.

IMPORTANT!

Read the operator's manual carefully before use and keep for future reference.

Symbols on the product:

General safety warnings

Electrical safety

DANGER! Electric shock!

injury due to electric current.

→ The product must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.

DANGER! Risk of physical injury!

of injury due to electric current.

→ Disconnect the product from the mains before you maintain or replace parts. Thereby the disconnected socket must be in the visual range.

Safe operating practices

The water temperature should not exceed 35 °C.

The pump must not be used when people are in the water.

Pollution of the liquid could occur due to leakage of lubricants.

Keep bystanders away from the water.

Operate the pump only with the elbow connector.

图

Circuit breaker

Thermal protection switch:

In the event of an overload, the pump is switched off by the built-in thermal motor protection. After sufficient cooling of the motor, the pump is operational again.

Automatic venting

This pump is equipped with a vent valve which eliminates any air pockets in the pump. Depending on the function, a small amount of water can escape from the side of the housing.

Additional safety warnings

Electrical safety

DANGER! Cardiac arrest!

This product makes an electromagnetic field while it operates. This field may under some conditions interfere with active or passive medical implants. To decrease the risk of conditions that can possibly injure or kill, we recommend persons with medical implants to speak with their physician and the medical implant manufacturer before you operate the product.

Cables

If extension cables are used, these must comply with the minimum cross-sections in the table below:

Voltage Cable length Cross section

230 – 240 V / 50 Hz Up to 20 m 1.5 mm	^2
230 – 240 V / 50 Hz 20 – 50 m 2.5 mm	^2

DANGER! Electric shock!

With a cut off mains plug, moisture can get into electrical parts via the mains cable and cause a short circuit.

→ Never cut the mains plug off (e. g. to feed through wall).
→ Don't use the power cable for plugging off.
→ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Mains plug and extension connections must be protected from water splashes.

Ensure that the electrical connections for plugs and sockets are made in areas safe from flooding.

Protect the mains plug and the mains power cable from heat, oil and sharp edges.

Observe the mains voltage. The information on the name-plate must be in agreement with the data for the mains power grid.

The pump's mains plug must be disconnected before anybody enters the swimming pool or touches the surface of the water.

The mains power cable must not be used for fastening or transporting the pump.

For submerging or lifting / securing the pump, please use a fastening rope.

Please regularly check the connecting line.

Before using, always subject the pump (especially the power cables and the power connections) to a visual inspection.

A pump which is damaged should not be used. In the event of damage, have the pump checked by GARDENA Service.

Assembly instructions: Retighten all screws by hand.

Before use after maintenance, make sure that all parts are screwed together.

When using our pumps with a generator, the warnings of the generator manufacturer must be observed.

Personal safety

DANGER! Risk of suffocation!

Small parts can be easily swallowed. There is also a risk that the polybag can suffocate toddlers. Keep toddlers away when you assemble the product.

Observe the minimum water level in accordance with the characteristics given for the pump.

Allow the pump to run no longer than 10 minutes against a closed pressure side.

Sand and other abrasive substances cause increased wear and reduce the pump's output.

The float switch may only be operated outside the water. The hose must not be disconnected during operation.

Allow the pump to cool down before troubleshooting.

The pump must not be operated without the mounted contra-angle handpiece.

2. ASSEMBLY

DANGER! Risk of injury!

Injury when the product starts accidentally.

→ Disconnect the product from the mains before you assemble the product.

To screw the elbow connector into the pump [Fig. A1]:

DANGER! Risk of injury!

Cut Injury by the impeller.

→ Operate the pump only with the elbow connector.

→ Screw the elbow connector① clockwise into the pump.
The hose can be connected via the pump connection ① and the convection nipple② [25 mm (1") and 38 mm (1 1/2")] or via the GARDENA Connection System [13 mm (1/2") / 16 mm (5/8") / 19 mm (3/4)]. When using a 38 mm (1 1/2") hose, the pump has the maximum delivery capacity.

Connect hose via connection nipple [Fig. A2/A3/A4]:

25 mm (1")- and 38 mm (1 1/2")-hoses can be connected via the connection nipple②.

Hose diameter 25 mm (1") 38 mm (1 1/2")

GARDENA Hose Clamp Art. 7193 Art. 7195

Hose connection[Fig. A2]

Do not detach nipple[Fig. A3].

Detach nipple at 6[Fig. A4].

25 mm (1")- and 38 mm (1 1/2") hoses connected with a connectionnipple ② must be fastened, for example with a GARDENA Hose Clamp Art. 7193/7195.

1. Screw the elbow connector into the pump.
2. Screw connection nipple ② onto the pump connection ①. (For 38 mm (1 1/2") hoses, first detach the connection nipple ② in the groove at (b).
3. Push the hose onto the connection nipple ② and fix e.g. with a GARDENA Hose Clamp Art. 7193/7195.

Connect hose via the GARDENA Connection System [Fig. A5]:

We do not recommend to use hoses with a diameter smaller than 19 mm (3/4"), as otherwise the flow rate will be reduced.

Hose diameter Pump connection

19 mm (3/4") GARDENA Pump Connection Set Art. 1752

→ Connect the hose via the relevant GARDENA Connection System.

3. OPERATION

DANGER! Risk of injury!

/ when the product starts accidentally.

→ Disconnect the product from the mains before you connect, adjust or transport the product.

To pump water:

If the pump cannot be immersed into the water reservoir via the handle, the pump must always be immersed into the well or water reservoir via a rope. Minimum immersion depth during initial operation see 7. TECHNICAL DATA.

Take care that the pump is located where the inlet openings at the suction base are not obstructed neither completely nor partly.

Stand the pump on a brick if using in a pond.

1. Submerge the pump in water reservoir.
2. Connect the pump to the mains. Attention! The pump begins operating immediately.

Automatic mode with float switch [Fig. 01]:

So that the pump automatically switches off when there is no liquid to pump, the Float Switch ③ must be able to freely move on the surface of the water.

To adjust the Cut-in and Cut-out Height [Fig. O1]:

The maximum cut-in height and minimum cut-out height (see 7. TECHNICAL DATA) can be adjusted by pushing the float switch wire into the float switch lock.

• The shorter the length of cable between the float switch ③ and the float switch lock Ⓐ, the lower the cut-in height and the higher the cut-out height.
  → Push the cable of the float switch ③ into the opening in the float switch lock Ⓐ.

CAUTION!

In order to ensure that the float switch is able to switch on and off, the cable length between the float switch and the float switch lock must be at least 10 cm.

Manual operation [Fig. O2]:

The pump remains permanently in operation because the float switch is bypassed.

1. Slide the float switch ③ with the cable downwards onto the float switch locking device Ⓐ.
2. Stand the pump on a firm surface.
3. Connect the pump to the mains. Attention! The pump begins operating immediately.

The minimum residual water depth (see 7. TECHNICAL DATA) is only achieved in manual mode because the float switch already switches off the pump before this when in automatic mode.

E

4. MAINTENANCE

DANGER! Risk of injury! Injury when the product starts accidentally.

→ Disconnect the product from the mains before you maintain the product.

To flush the pump:

After pumping chlorinated water, the pump must be flushed.

1. Pump lukewarm water (max. 35 °C), possibly adding a mild cleaning agent (e.g. detergent) until the pumped water runs clear.
2. Remove residuals according to the waste disposal laws applicable in your area.

5. STORAGE

To put into storage:

The pump is not frost-proof!

The product must be stored away from children.

1. Disconnect the pump from the mains.
2. Turn the pump upside down until no more water runs out.
3. Clean the pump (see 4. MAINTENANCE).
4. Store the pump in a dry, enclosed and frost-free place.

Disposal:

(in accordance with RL2012/19/EC)

The product must not be disposed of to normal household waste. It must be disposed of in line with local environmental regulations.

IMPORTANT!

→ Dispose of the product through or via your municipal recycling collection centre.

6. TROUBLESHOOTING

DANGER! Risk of injury! Injury when the product starts accidentally.

→ Disconnect the product from the mains before you troubleshoot the product.

To clean the suction base and the impeller [Fig. T1]:

1. Unscrew the 4 Phillips screws ④.

2. Pull the suction base ⑤ off the pump.

3. Clean suction base ⑤ and impeller ⑥ (the warranty does not become void as a result of this maintenance work).
4. Reinstall the suction base ⑤.
5. Screw in the 4 Phillips screws ④ again.

For safety reasons a damaged impeller can only be exchanged by the GARDENA Service Centre.

Problem	Possible Cause	Remedy
Pump is running, but doesn't deliver water	Air cannot escape, because the pressure line is closed. (Possible kink in the pressure hose.)	→ Open the pressure line (e.g. shut-off valve, delivery units).
	Air in suction foot.	→ Wait for about 60 seconds until the pump has vented; if necessary, turn off and then on again.
	Suction opening is clogged.	→ Clean the suction opening with a water jet.
	Hose is clogged.	→ Remove the clog from the hose.
	Impeller is blocked.	→ Clean the impeller.
	Water level below minimum water level when put into operation.	→ Submerge the pump deeper.
Pump does not start, or stops suddenly during operation	Thermal switch has turned the pump off because of overheating.	→ Clean the suction opening. Observe the max. media temperature (35 °C).
	No power supply to the pump.	→ Check fuses and electrical plug connections.
	RCD has triggered (residual current).	→ Disconnect the pump and contact the GARDENA Service.

14

Problem Possible Cause Remedy

Pump is running but the delivery drops suddenly	Suction opening is clogged. → Clean the suction opening with a water jet.
	Hose is clogged. → Remove the clog from the hose.

NOTE: For any other malfunctions please contact the GARDENA service department. Repairs must only be done by GARDENA service departments or specialist dealers approved by GARDENA.

1. TECHNICAL DATA

Submersible Pump Unit Value		(Art. 9000)	Value (Art. 9001)	Value (Art. 9007)	Value (Art. 9008)
Rated power W 250 400 250 400
Mains voltage V (AC) 230 230 230 230
Mains frequency Hz 50 50 50 50
Max. delivery capacity	l/h	8200	8600	9200	10,500
Max. pressure/ max. delivery head	bar / m	0.5 5.0	0.55 5.5	0.4 4.0	0.5 5.0
Max. submersion depth	m	6	6	6	6
Min./max. cut-in height	cm	23 / 50	23 / 50	26 / 45	26 / 45
Min./max. cut-out height	cm	7 / 20	7 / 20	11 / 16	11 / 16
Residual water level	mm	4	4	25	25
Dirty water with max. particle diameter	mm	5	5	25 25
Minimum water depth for operation (approx.)	cm	25 25 50 50
Power cable	m	10 (H05RN-F)	10 (H05RN-F)	10 (H05RN-F)	10 (H05RN-F)
Weight without cable (approx.)	kg	2.55	2.85	2.55	2.9
Max. media temperature	°C	35 35 35 35

1. ACCESSORIES

GARDENA Hose Clamp	For 25 mm (1") hoses via the connection nipple.	Art. 7193
GARDENA Hose Clamp	For 38 mm (1 1/2") hoses via the connection nipple.	Art. 7195
GARDENA Pump Connection Set	For 19 mm (3/4") hoses via the GARDENA Connection System.	Art. 1752
GARDENA Flat Hose Set	10 m 38 mm (1/2") hose with hose clamp.	Art. 5005

EN

9. SERVICE/WARRANTY

Service:

Please contact the address on the back page.

Warranty statement:

In the event of a warranty claim, no charge is levied to you for the services provided.

GARDENA Manufacturing GmbH grants a warranty for all original GARDENA new products for two years from the date of original purchase from the retailer, provided that the devices have been for private use only. This manufacturer's warranty does not apply to products acquired second hand. This warranty includes all significant defects of the product that can be proved to be material or manufacturing faults. This warranty is fulfilled by supplying a fully functional replacement product or by repairing the faulty product sent to us free of charge; we reserve the right to choose between these options. This service is subject to the following provisions:

• The product has been used for its intended purpose as per the recommendations in the operating instructions.
• Neither the purchaser nor a third party has attempted to open or repair the product.
• Only Original GARDENA replacement parts and wear parts have been used for operation.

- Presentation of the receipt.

Normal wear and tear of parts and components (such as blades, blade fixing parts, turbines, light bulbs, V-belts / toothed belts, impellers, air filters, spark plugs), visual changes, wear parts and consumables are excluded from the warranty.

This manufacturer's warranty is limited to replacement and repair of products in accordance with the abovementioned conditions. The manufacturer's warranty does not constitute an entitlement to lodge other claims against us as a manufacturer, such as for damages. This manufacturer's warranty does not, of course, affect statutory and contractual warranty claims against the dealer / retailer.

The manufacturer's warranty is governed by the law of the Federal Republic of Germany.

In case of a warranty claim, please return the faulty product, together with a copy of the receipt and a description of the fault, with postage paid to the service address.

Consumables:

The impeller is a consumable and is not included in the warranty.

Please contact the address on the back page.

FARE! Fare for kvelning!

Close-up of a black industrial device with a white arrow pointing to a pipe fitting (no visible text or symbols)

Performance characteristics

Courbes de performance

Prestatiegrafiek

Kapacitetskurva

Ydelses karakteristika

Pumpun ominaiskäyrä

Pumpekarakteristikk

Curva di rendimento

ROBERTO C. RUMBO S.R.L.

Predio Norlog

Lote 7

Benavidez. ZC:1621

Buenos Aires

Husqvarna Australia Pty. Ltd.

Locked Bag 5

Central Coast BC

NSW 2252

Phone: (+61) (0) 2 4352 7400

customer.service@

husqvarna.com.au

Austria/Österreich

Husqvarna Austria GmbH

Industriezeile 36

4010 Linz

Tel.: [phone]

service.gardena@

husqvarnagroup.com

Azerbaijan

Firm Progress

a. Aliyev Str. 26A

1052 Baku

Belarus

Private Enterprise

"Master Garden"

Minsk

Sharangovich str., 7a

Phone: [phone]

Mob.: [phone]

[e-mail]

Belgium

Husqvarna Belgium nv

Gardena Division

Leuvensesteenweg 542

Planet II E

1930 Zaventem

België

Bosnia / Herzegovina

SILK TRADE d.o.o.

Industrijska zona Bukva bb

74260 Tešanj

Brazil

Brampton, Ontario L6T 4X3

Phone: [phone]

[e-mail]

Chile

REPRESENTACIONES

JCE S.A.

No207, Song Hong Rd.,

Chang Ning District,

Shanghai

PRC. 200335

上海市长宁区淞虹路207号明

基广场B座3楼，邮编：200335

Colombia

Husqvarna Colombia S.A.

Calle 18 No. 68 D-31, zona

Industrial de Montevideo

Bogotà, Cundinamarca

Tel. [phone] ext. 105

jairo.salazar@

husqvarna.com.co

Costa Rica

Compania Exim

Euroiberoamericana S.A.

Los Colegios, Moravia,

8/57 Beliashvili street

0159 Tbilisi, Georgia

Phone: [phone]

Great Britain

Husqvama UK Ltd

Preston Road

Avcliffe Industrial Park

Newton Avcliffe

County Durham

DL5 6UP

info.gardena@

husqvarna.co.uk

Greece

Π.ΠΑΠΑΔΟΠΟΥΛΟΣ ΑΕΒΕ

Λεωφ. Αθηνών 92

Αθήνα

T.K.104 42

Ελλάδα

Tηλ. ([phone]

[e-mail]

Hungary

Aycliffe Industrial Park

Newton Aycliffe

County Durham

DL5 6UF

info.gardena@

husqvarna.co.uk

Italy

23868 VALMADRERA (LC)

Phone: [phone]

assistenza.italia@

it.husqvarna.com

Japan

Husqvama Zenoah Co., Ltd

1-9 Minamidai

Kawagoe

350-1165 Saitama

gardena-ip@

husqvarnagroup.com

Kazakhstan

LAMED Ltd.

155/1, Tazhibayevoi Str.

050060 Almaty

IP Schmidt

Abavavenue 3B

110 005 Kostanay

Korea

Kyung Jin Trading CO.,LTD.

107-4, SunDuk Bld.,

YangJae-dong,

Seocho-gu

Seoul, (zipcode: 137-891)

Phone: (+82) (0)2 574-6300

Kyrgyzstan

Alye Maki

av. Moladaya Guardir J 3

720014

Bishkek

Latvia

Husqvarna Latvija SIA

Ulbrokas 19A

LV-1021 Rīga

[e-mail]

Lithuania

UAB Husqvarna Lietuva

Ateities pl. 77C

LT-52104 Kaunas

[e-mail]

Luxembourg

Magasins Jules Neuberg

1. rue Jacques Stas

Luxembourg-Gasperich 2549

Case Postale No. 12

Luxembourg 2010

Phone: [phone]

[e-mail]

Mexico

AFOSA

Husqvama New Zealand Ltd.

PO Box 76-437

Manukau City 2241

Phone: (+64) (0) 9 9202410