FSP 5500 Economic - Pump GARDENA - Free user manual and instructions

USER MANUAL FSP 5500 Economic GARDENA

Line drawing of a mechanical device with a mesh grille and coiled cable (no text or symbols)

FSP 3500 Art. 7862

Technical line drawing of a mechanical device with a cylindrical shaft and threaded end (no text or symbols)

FSP 5500 Economic Art. 7863
FSP 8500 Economic Art. 7864
FSP 12000 Economic Art. 7865
FSP 16000 Economic Art. 7866

D Betriebsanleitung

Filter-/ Bachlaufpumpe

GB Operating Instructions

Filter / Stream Pump

F Mode d'emploi

Translation of the original instructions from German. Please read these operating instructions carefully and observe the notes given. Use these operating instructions to get to know the GARDENA Filter / Stream pump, its correct use and the safety instructions.

For safety reasons, children under 16 as well as persons not familiar with these operating instructions should not use this GARDENA Filter / Stream Pump.

→Keep these operating instructions in a safe place.

Contents

1. Where to use Your GARDENA Filter / Stream Pump.....10
2. Safety Instructions .... 10
3. Function 11
4. Initial Operation ...... 12
5. Storing your Filter / Stream Pump 13
6. Maintenance .... 13
7. Troubleshooting ..... 14
8. Accessories 15
9. Technical Data 15
10. Service 16

1. Where to use Your GARDENA Filter / Stream Pump

Intended Use

The GARDENA Filter / Stream Pump is intended for domestic use. It is intended for pumping water outdoors together with a pond filter in case of dirty water or for use with streams. It is not intended for operating watering tools and accessories or irrigation systems.

Please note

The GARDENA Filter / Stream Pump is not suitable for continuous operation in industrial applications. Corrosive, easily combustible, aggressive or explosive substances, (such as gasoline, petroleum or nitro thinner), saltwater and food must not be pumped.

2. Safety Instructions

Electrical Safety:

The pump should be operated via a residual current device with a residual current rating of ≤ 30 mA (DIN VDE 0100-702 and 0100-738). The pump must be placed on solid, even ground.

→Please ask your electrician for his advice.

Always disconnect the pump from the mains before undertaking any work on it.

Mains power cables should not have a smaller cross-section than a rubber sheathed cable of the designation H05 RN-F3G0,75 (art. no. 7862), H05 RN-F3G1 (art. no. 7863 / 7864 / 7865 / 7866). Extension cables must meet the requirements of DIN VDE 0620.

Check line voltage. Data indicated on the type plate must match technical data of the mains supply.

Please unplug the pump after operation and before carrying out any maintenance works.

The pump must not be operated when there are people in the water. Swimming pools and garden ponds should be designed according to international and national design regulations.

→Please consult a professional electrician.

For Austria:

Pumps for use on swimming pools and on ponds may only be operated via an isolating transformer.

→Please consult a professional electrician.

For Switzerland:

In Switzerland mobile appliances which are used outdoors, must be connected via a residual-current device.

Note:

Do not allow the pump to run without water because dry-running leads to an undesirable build up of heat.

Before operating the pump, look to see if there is any damage of the pump (esp. regarding power cable and plug). The connection cable of the pump cannot be replaced. If the cable is damaged the pump must be scrapped.

Do not use the power cable to carry the pump or to pull the plug out of the socket. Protect the power cable from heat, oil and sharp edges.

Ensure that the power cable cannot be crushed if it has not been laid in conduit in the earth or in gravel.

The temperature of the liquid used must not be below 4 °C or above 35°C.

Sand and other abrasive substances in the liquid cause increased wear and reduce the output of the pump.

Please observe the local noise prevention regulations.

3. Function

Economic Pumps:

The new GARDENA Economic Pumps come with energy-efficient, reliable motor technology for powerful continuous operation. Up to 40% energy saving compared to the technology used so far.

Automatic Energy Control (AEC) (only for FSP 12000 / 16000 Economic):

Automatic Energy Control Energy max. Energy min.

Thanks to AEC, the pump automatically optimises the flow rate depending on the water temperature and so cuts the power consumption by as much as a further 20% (AEC set to “On”). The flow rate is reduced in the process by up to 50%. The colder the pond water, the lower the flow rate.

To ensure that the delivery capacity is always constant (e.g. when the pump is used as a stream pump), AEC can also be switched off (AEC set to "Off").

4. Initial Operation

Connecting the hoses:

Technical diagram of a mechanical device with labeled parts ① and ②

Switch Automatic Energy Control (AEC) on:

Technical diagram of a vacuum cleaner with numbered parts labeled ② to ⑥

Switch pump on:

Diagram illustrating a water treatment or irrigation system with labeled components including a pump, tank, and vegetation.

The universal connector ① can be used to connect 3 14 (for FSP 3500 only), 1% , 1 14 and 1 12 hoses.

To achieve the best pumping results (maximum delivery rate of the pump) use a 38 mm (1½")-hose. We recommend that you secure all hoses using GARDENA Hose Clips art. no. 7192 / 7195.

1. Depending on the hose, cut away the parts of the universal connector ① you do not need using a saw.
   Otherwise loss of performance could occur.
2. Screw universal connector ① onto the pump.
3. FSP 5500 - FSP 16000: Pay attention that the O-ring Ⓞ is inserted correctly.
4. Connect hose to the universal connector ①.

Only for FSP 12000 Economic / FSP 16000 Economic:

1. Undo screws ⑥ (transit support).
2. Press in snap fastening ② and open up the filter housing ③.
3. Set switch ④ to the position wanted On / Off.

On = AEC switched on

Off = AEC switched off

1. Close the filter housing ③ and fit the screws ⑥ back into place, if applicable.

If using a pond filter, separate the filter outlet and the pump by as much distance as possible in the pond. This will achieve the best possible cleaning effect for the pond water.

→ Note the maximum submersion depth (see 9. Technical Data).

1. Place the pump in the water in such a way that the filter housing ③ is covered by at least 20 cm of water.

2. Plug mains plug into an AC socket.

Warning: Pump will start immediately.

For infinitely variable control of the flow rate and in case of 2 connection points (e.g. simultaneous operation of stream and filter), the GARDENA 2-way Regulator Valve Art. 7867 ^⑤ can be used.

5. Storing your Filter / Stream Pump

Overwintering:

The pump should be stored out of the reach of children.

For FSP 3500 / FSP 5500 Economic / FSP 8500 Economic:

1. Remove the pump from the pond before frost is expected and clean.
2. To avoid difficulties when starting up in the spring, we recommend storing the pump in a frost-free location in a container filled with water.
   The mains plug must not be submerged.

The FSP 12000 Economic / FSP 16000 Economic Pumps are frost-proof and therefore can be left in the pond over the winter.

Disposal: (in accordance with RL2002/96/EC)

The product must not be added to normal household waste. It must be disposed of in line with local environmental regulations.

→Important: Make sure that the unit is disposed of via your municipal recycling collection centre.

6. Maintenance

Clean filter housing:

Technical diagram of a vacuum cleaner with numbered components for identification

DANGER! Electric shock!

→Disconnect the pump from the mains before working on it!

Do not use any hard objects or powerful detergents for cleaning the set!

1. Take filter / stream pump out of the water.
2. Unscrew the screws ⑥ (not for FSP 3500).
3. Press in snap fastening ② and open up the filter housing ③.
4. Remove pump ⑦ and clean the filter housing ③ with a jet of water.
5. Re-insert pump ⑦, close the filter housing ③ and fit the screws ⑥ (not for FSP 3500) back into place if applicable.

7. Troubleshooting

Clean the pump:

Technical diagram of a mechanical assembly with numbered parts labeled 8, 9, and 11

FSP 3500

DANGER! Electric shock!

→Disconnect the pump from the mains before working on it!

FSP 3500:

1. Remove pump from the filter housing (see 6. Maintenance).
2. Turn pump housing ⑧ anti-clockwise and pull vertically off the motor housing ⑨ (bayonet fitting).
3. Clean the motor housing ⑨ and pump housing ⑧.
4. Pull the impeller unit ⑪ out of the motor housing ⑨ clean and push back into the motor housing ⑨.
5. Press pump housing ⑧ vertically onto the motor housing ⑨ and turn clockwise (bayonet fitting).

Technical diagram of an electric motor with numbered parts for identification

FSP 5500 Economic

FSP 5500 Economic / FSP 8500 Economic:

1. Remove pump from the filter housing (see 6. Maintenance).
2. Undo screws ⑯ and remove pump housing ⑧.
3. Pull the impeller unit ⑪ out of the motor housing ⑨ clean and push back into the motor housing ⑨.
4. Clean the motor housing ⑨ and pump housing ⑧.
5. Press pump housing ⑧ upright onto the motor housing ⑨ and fit the screws ⑯.
   During assembly, pay attention that the O-ring ^⑫ is correctly placed in the motor housing ^⑨ .

Technical diagram of a mechanical assembly with numbered components for identification

FSP 8500 Economic

FSP 12000 Economic /

FSP 16000 Economic

FSP 12000 Economic / FSP 16000 Economic:

1. Remove pump from the filter housing (see 6. Maintenance).
2. Unscrew and clean collar ⑬ along with foam plastic ⑭ and O-ring ⑮.
3. Undo screws ⑯ and remove pump housing ⑧.
4. Pull the impeller unit ⑪ out of the motor housing ⑨ clean and push back into the motor housing ⑨.
5. Clean the motor housing ⑨ and pump housing ⑧.
6. Press pump housing ⑧ upright onto the motor housing ⑨ and fit the screws ⑯.
   During assembly, pay attention that the gasket ^⑫ is correctly placed in the motor housing ^⑨ .
7. Screw on collar ⑬ along with foam plastic ⑭ and O-ring ⑮. During assembly, pay attention that the O-ring ⑮ is correctly placed in the pump housing ⑧.

Fault Possible Cause Remedy

No water being conveyed	Mains plug not plugged in. → Plug in mains plug.
	Impeller unit blocked. →Clean pump.
	Thermal overload switch has 1. Unplug the mains plug and been activated allow the pump to cool. (pump has run dry).	2. Plug the mains plug back in after approx. 2 minutes.
Reduced amount of water being conveyed	Filter housing is dirty. → Clean filter housing.
	AEC activated. →Switch off AEC.

In the event of other faults please contact GARDENA Service. Repairs should only be carried out by GARDENA service centres or dealers authorised by GARDENA.

1. Accessories

GARDENARemote Control Set	For remote control of electric devices, indoors and outdoors.	Art. Art. 7680
GARDENARibbed Pond Hose	For connecting pump and stream or pond filter.	Art. 7830 – 7833
GARDENA2-way Regulator Valve	For infinitely variable control of the flow rate and in case of 2 connection points (e.g. simultaneous operation of stream and filter).	Art. 7867

1. Technical Data

	Art. 7862FSP 3500	Art. 7863FSP 5500Economic	Art. 7864FSP 8500Economic	Art. 7865FSP 12000Economic	Art. 7866FSP 16000Economic
Rated power	70 W	60 W	80 W	130 W	170 W
Max. flow	3,300 l/h	5,300 l/h	8,300 l/h	12,000 l/h	15,500 l/h
Max. delivery head	2,6 m	2,8 m	3,2 m	5,0 m	5,6 m
Max. submersion depth	2 m	4 m	4 m	4 m	4 m
Power cable	H05 RN-F3G0.75	H05 RN-F3G0.75	H05 RN-F3G1.0	H05 RN-F3G1.0	H05 RN-F3G1.0
Pump universal connections	34" / 1" / 114" / 112"	1" / 114" 112"	1" / 114" 112"	1" / 114" 112"	1" / 114" 112"
Min./max. Media temperature	4°C - 35°C	4°C - 35°C	4°C - 35°C	4°C - 35°C	4°C - 35°C
Mains voltage/frequency	230 V/50 Hz	230 V/50 Hz	230 V/50 Hz	230 V/50 Hz	230 V/50 Hz

10. Service

Guarantee

GARDENA guarantees this product for 3 years (from date of purchase). This guarantee covers all serious defects of the unit that can be proved to be material or manufacturing faults. Under warranty we will either replace the unit or repair it free of charge if the following conditions apply:

• The unit must have been handled properly and in keeping with the requirements of the operating instructions.
• Neither the purchaser or a non-authorised third party have attempted to repair the unit.

The feed impeller is a wearing part and is not covered by the warranty.

This manufacturer's guarantee does not affect the user's existing warranty claims against the dealer/seller.

If you have any problems with your GARDENA Filter / Stream Pump, please contact our Service or return the defective unit together with a short description of the problem – in case of guarantee, with a copy of the receipt – postage paid to one of the GARDENA Service Centres listed on the back of this leaflet.

FSP 3500: Art. 7862

Pumpen-Kennlinie

Performance characteristics

Courbes de performance

Prestatiegrafiek

Kapacitetskurva

Curva di rendimento

Performance characteristics

Courbes de performance

Prestatiegrafiek

Kapacitetskurva

Curva di rendimento

Performance characteristics

Courbes de performance

Prestatiegrafiek

Kapacitetskurva

Curva di rendimento

Husqvarna Australia Pty. Ltd.

Locked Bag 18

Gosford NSW 2250

Phone: (+61) (0) 2 4372 1500

customer.service@

husqvarna.com.au

GARDENA Belgium NV/SA

Brampton, Ontario L6T 4X3

Phone: [phone]

[e-mail]

Chile

Antonio Martinic y Cia Ltda.

Cassillas 272

Centro de Cassillas

Santiago de Chile

Phone: [phone]

[e-mail]

Costa Rica

Compania Exim

Euroiberoamericana S.A.

Los Colegios, Moravia,

Husqvarna Consumer Outdoor

Products

Consumer Outdoor Products

Consumer Outdoor Products

Lautatarhankatu 8 B / PL 3

00581 HELSINKI

[e-mail]

France

GARDENA France

Immeuble Exposal

Aycliffe Industrial Park

Newton Aycliffe

County Durham

DL5 6UP

info.gardena@

husqvarna.co.uk

Greece

HUSQVARNA GREECE S.A.

Branch of Koropi

Ifestou 33A

Industrial Area Koropi

194 00 Athens – Greece

V.A.T. EL094094640

Phone: [phone]

[e-mail]

Hungary

Husqvarna

Magyarország Kft.

Ezred u. 1-3

1044 Budapest

Phone: [phone]

[e-mail]

Iceland

O. Johnson & Kaaber

Tunguhalsi 1

110 Reykjavik

[e-mail]

Ireland

Michael McLoughlin & Sons

Hardware Limited

Long Mile Road

Dublin 12

Italy

Phone: [phone]

[e-mail]

Japan

KAKUICHI Co. Ltd.

Sumitomo Realty &

Development Kojimachi

BLDG., 8F, 5-1 Nibanncyo,

Chiyoda-ku, Tokyo 102-0084

Phone: [phone]

[e-mail]

Latvia

Consumer Outdoor Products

Consumer Outdoor Products

Ateities pl. 77C

LT-52104 Kaunas

[e-mail]

Luxembourg

Magasins Jules Neuberg

Husqvarna New Zealand Ltd.

PO Box 76437

Manukau City 2241

Phone: (+64) [phone]

Norway

GARDENA

Husqvarna Consumer Outdoor

Products

Salgskontor Norge

Kleverveien 6

1540 Vestby

[e-mail]

Poland

Sintra Business Park

02-08 Tat Ann Building

Singapore 577185

Phone: [phone]

[e-mail]

Slovak Republic

GARDENA spol. s r.o.

Tuřanka 115

627 00 Brno

Phone: [phone]

Husqvarna Consumer Outdoor

Products