Safe Auto M1200 - Shredder HAMA - Free user manual and instructions

USER MANUAL Safe Auto M1200 HAMA

Line drawing of a modern kitchen appliance with control panel and door (no text or symbols)

OperatingInstructions

Bedienungsanleitung

Moded'emploi

Instruccionesdeuso

Gebruiksaanwijzing

Istruzioniperl'uso

Instrukcja o bsługi

Használatiútmutató

Manualdeutilizare

Návodk p oužití

Návodnapoužitie

Manualdeinstruções

Bruksanvisning

1. Connectingcable(backofthedevice)

2. Warningsymbols

3. Paperguideflap(automaticintake)

4. Pull-outcollectioncontainer

8.Viewingwindow

1. Onwheels

a)withwheellock(front)

b) withoutwheellock(rear)

10.MainswitchOn/Off(ontheside)

1. "REVERSE" button(backwards)

2. "FORWARD" button(forwards)

13."ON/OFF"key

1. ContainerstatusLED

2. Overheating / overload status LED

3. ReadystatusLED

1. Introduction

1.1 Foreword

Thankyouforchoosinga H amaproduct.

Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions onto the new owner.

Note— Importance of the operating instructions

Failure to observe the operating instructions when using the product constitutes incorrectuseorwilfulmisuseandisnotpermitted.

Note

This device is a new, unused product.

Anycuttingresiduepresentmayhavebeenleftoverfromqualityassurancetestsduring production.

1.2 Explanationofwarningsymbolsandnotes

Riskofelectricshock

This symbol indicates a risk of electric shock from touching product parts carrying hazardous voltage.

Warning

This symbol is used to indicate safety instructions to draw your attention to specific hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

1.3 Packagecontents

• "SAFEAutoM1200" shredder

• Theseoperatinginstructions

2.Safety

2.1 Correctuse

- This product is intended for the destruction of documents both in the home and in the commercial sector, provided the applications are comparable with typical household use (e.g. in offices, workshops and hotels, etc.).

- Usetheproductonlyfortheintendedpurpose.

- Theproductisintendedonlyforuseinsidebuildings.

- Protect the product from dirt, moisture and overheating and use it in dry rooms only.

- Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.

- Do not use the product in a damp environment and avoid splashing water.

- Do not operate the product outside the power limits specified in the technical data.

- Do not operate the product continuously, as it is not designed for this.

- Do not use the product in areas in which electronic products are not permitted.

- Do not drop the product and do not expose it to any major shocks.

- This product is not intended for use by persons, including children, with limited physical, sensory or mental abilities or lacking in experience or knowledge, unless they are supervised by a person responsible for their safety or have been instructed on how to use the product.

• As with all electrical products, this device should be kept out of the reach of children.

- Keep the packaging material out of the reach of children due to the risk of suffocation.

- Disposeofpackagingmaterialimmediatelyinaccordancewiththelocallyapplicable regulations.

- Do not modify the product in any way. Doing so voids the warranty.

- Onlyusethearticleundermoderateclimaticconditions.

• Always pull directly on the plug when disconnecting the cable, never on the cable itself.

Note

Theproductisonlyintendedforvolumesgeneratedbyhouseholds.

Warning

Any use is permitted only with the paper container provided.

Note— Commercial use

• If the device is used commercially, increased duty of care requirements apply.

- Therefore, please observe the accident prevention regulations of the German employer's liability insurance association for electrical systems and equipment. Please also observe all accident prevention regulations from other applicable employer's liability insurance associations and accident insurance companies, as well as any legal regulations applicable to the particular industry and/or location.

The following materials may and may NOT be shredded:

Paper

Paperwithstaples

Magneticstrip and I D c hipcards

CDs, DVDs, Blu-Rays

Continuous paper, sticky labels, slides, newspaper, cardboard, paper clips, laminate, plastic (with the exception of the objects stated earlier)

2.2 Basicsafetyinstructions

Please not the following safety instructions in order to set devices safely:

• Check the device before use for any visible external damage. Do not put a damaged device into operation.
• People who, as a result of their physical, mental or motor capacities, are unable to operate the device safely must only use the device under supervision or after instruction by a responsible person.
• Faulty components must only be replaced with original spare parts. Only these parts are guaranteed to meet the required safety standards.
• Protect the device against moisture and the penetration of liquids or objects. In the eventofcontactwithliquid, disconnectthe devicefromthepowersupplyimmediately.

Warning - risk of cutting on the cutting rollers

Donottouchthecuttingrollers.

Riskofelectric shock

• Do not open the device or continue to operate it if it becomes damaged.
• Do not use the product if the AC adapter, adapter cable or power cable is damaged.
• Do not attempt to service or repair the product yourself. Leave any and all service worktoqualifiedexperts.

2.3 Explanation of symbols used on the product label

Warning - risk of injury

Note the warning symbols in order to avoid injuries or damage to the device.

General warning symbol

Before c ommissioning, read the enclosed operating instructions.

You must comply with the safety instructions at all times.

• This device is not intended for use by children.
- Avoid touching the intake opening with hands, clothing or hair.
- Unplug the device if it is not going to be used for a prolonged period.

Children must be supervised when using the device.

Do not insert paper clips into the intake s haft.

Do not reach into the intake shaft.

Keep clothing away from the intake shaft.

Keep jewellery, e.g. necklaces, away from the intake shaft.

Keep hair away from the intake shaft.

Do not use any aerosol products on or near the device.

Insert no more than 5 sheets of paper at any one time into the manual intake shaft (1).

Do not insert CDs/DVDs into the intake shaft (1/2).

Intake shaft for credit cards. Only insert one credit cardata time into the intake shaft for credit cards.

Press the paper guide flap (6) down.

First load the unstapled side of the paper into the automatic intake shaft (2). Maximum 10 sheets stapled together.

Insert no more than 120 sheets of paper at any one time into the automatic intake shaft (2).

Plastic cards must not be shredded in the automatic intake shaft.

Do not insert paper clips into the automatic intake shaft.

Sharp edge! Do not touch!

2.4 Safety device

The device is equipped with a safety switch and can only be operated if the basket (7) is correctly inserted into the device.

Warning

Any tampering with or modification of the safety features can result in serious injury and is not permitted.

3. Installation / Setup

Warning

• Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
• Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
• If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip's maximum throughput rating.
• If you will not be using the product for a prolonged period, disconnect it from mains power.

Note

• Set the product up on a level, horizontal and sufficiently stable surface.
• Route all cables so that there is no risk of tripping.
• Do not bend or crush the cable.
• Protect the connecting cable from hot surfaces and sharp edges.

- Connect the mains cable to a properly installed and easily accessible mains socket.

4. Operation

Note

• Be aware that the thickness of paper increases when it is folded, leading to the device's maximum page capacity being exceeded.
  • Always wait until one cutting operation is finished before starting the next one.
• Do not use the device continuously for more than 60 minutes at a time.
• Empty the container regularly in order to avoid damaging the device.

4.1 Switching the device on

• Move the main switch (10) to the "|" position.
• Press the "ON/OFF" button (13).
  • The Ready status LED (16) lights up solid green.
  • The device is now ready for use.

4.2 Switching the device off

• Press the "ON/OFF" button (13).
  • The Ready status LED (16) goes out.
• Move the main switch (10) to the "O" position.

Note

If too much paper is fed in at the same time, the shredder stops automatically and ejects the paper backwards. The Overload status LED (15) lights up and the Ready status LED (16) starts flashing. This may have been caused by too much paper being stapled, paper that is too thick, folded or not stacked neatly. Remove the excess paper and reduce the number of sheets if necessary.

4.3 Manualintakeshaft

Shreddingpaper

• Insert the paper into the centre of the intake shaft (1). The cutting rollers switch on automatically.
• Let go of the paper. Once the cutting process is complete, the cutting rollers switch themselves off again.

Shreddingplasticcards

Note

This shredder is primarily designed for paper. Excessive shredding of plastic cards could reduce the life of the machine.

• Insert the plastic card into the centre of the intake shaft (1). The cutting rollers switch onautomatically.
• Let go of the plastic card. Once the cutting process is complete, the cutting rollers switch themselvesoffagain.

4.4 Automaticintakeshaft(only suitable for paper)

Warning

Plasticcardsmustnotbeshreddedintheautomaticintakeshaft.

Warning

Do not load additional paper in the automatic intake shaft if the shredding process is alreadyinprogress.

Warning

Do not load folded paper in the automatic intake shaft as this may cause a paper jam.

Note

It is recommended to remove all staples from the paper before shredding it to prolong the life of the machine. If you want to shred paper with staples, first load the non-stapled side of the paper in the automatic intake. This shredder cuts a maximum of 10 stapled sheets in the automatic intake.

• Arrange the paper to be shredded neatly in a pile. Open the cover (3).
• Press down the centre of the paper guide flap (6) and insert the stack of paper into the automaticintake(2).
  • Make sure you push the paper stack down as far as it will go. Let go of the stack of paper.
  • The cutting rollers switch on automatically.
• Once the cutting process is complete, the cutting rollers switch themselves off again.
  • Closethecover(3)topreventdamagetoit.

4.5 Forwards/ backwards modes

Note

These modes are designed to release any blockages of the cutting mechanism.

Manualintakeshaft

If a paper jam is detected in the manual intake shaft, the shredder stops automatically and ejects the paper backwards (1). If the paper then does not come loose, carry out the following steps.

• Press and hold the "REVERSE" button (11). The rollers of the cutting unit now rotate in theoppositedirectionanddischargethepaperbackwards.
• Remove the blocked cut material carefully from the intake shaft (1).
  • TheReadystatusLED(16)flashes.
• Ensure that the amount of paper does not exceed the maximum capacity.
• Oncethepaperjamiscleared, pressthe "FORWARD" button(12)tocontinuethe shreddingprocess.

Automaticintakeshaft

If a paper jam is detected in the automatic intake shaft, the shredder stops automatically and ejects the paper backwards (2). If the paper then does not come loose, carry out the following steps.

• Press and hold the "REVERSE" button (11). The rollers of the cutting unit now rotate in theoppositedirectionanddischargethepaperbackwards.
• Press down the centre of the paper guide flap (6) and carefully remove the jammed paper from the intakeshaft(2).
  •TheReadystatusLED(16)flashes.
• Stack the paper neatly on top of each other. Make sure the amount of paper does not exceed them maximum capacity and stapled paper pages are on top.
• Once the paper jam is cleared, press the "FORWARD" button (12) to continue the shredding process.

5. Care and maintenance

Danger – risk of death from electric shock

Disconnect the mains plug from the socket before starting any cleaning work.

Warning - risk of cutting on the cutting rollers

Donottouchthecuttingrollers.

Warning - damage to the device from moisture

Ensure, when cleaning, that no moisture penetrates the device in order to avoid irreparable damagetot.

5.1 Emptyingthecontainer

Note

The Container status LED (14) lights up solid red and the shredder stops when the containerisfull.

• Switch the device off - as described in 4.2 Switching the device off - and disconnect themainsplug.
• Pull thebasket(7)out.
• Emptythecontainer.
• Pushthebasket(7)backin.
• Reconnect the device - as described in 3. Installation/Setup - to the power supply.

5.2Cleaningthedevice

• Switch the device off - as described in 4.2 Switching the device off - and disconnect themainsplug.
• Clean the device with a dry cloth. In cases of heavy soiling, the cloth can be dampened a little.
• Allow the device dry completely afterwards.
• Reconnect the device - as described in 3. Installation/Setup - to the power supply.

5.3 Cleaning/o ilingthecuttingrollers

Note

• Oil the cutting rollers after each emptying of the waste paper basket in order to prolongtheshredder'sservicelife.
• You can find an appropriate selection of cleaning products at www.hama.com.

- Switch the device on - as described in 4.1 Switching the device on.

5.3.1 Cleaning with Hama cleaners for shredders (item number: 113820)

• Apply the Hama cleaner for shredders (item number: 113820) in several strips onto a pieceofDINA4-sizepaper.
• Insert the paper into the centre of the intake shaft (1). The cutting rollers switch on automatically.
• Once the cutting process is complete, the device is ready for operation again.

5.3.2 Cleaningwithcleaningpaper

• Insert the cleaning paper into the centre of the intake shaft (1). The cutting rollers switch onautomatically.
• Once the cutting process is complete, the device is ready for operation again.

6.Troubleshooting

ErrorPossiblecauseRemedy
Thecuttingrollersdonot switchonautomatically whenmaterialtobe shreddedisinserted.	Themainswitch(10) is in the"O"position.	Movethemainswitch (10)tothe"l"position.
	The"ON/OFF"button ( 13) wasnotpressed.	Pressthe"ON/OFF" button(13)untilthe ReadystatusLED(16) lightsupsolidgreen.
	Thecollectingcontainer (7)isnotinserted properly.	Insertthecollecting container(7)properly.
	Thepaperguideflap(6) (automaticintake)has no t beenpresseddown.	Holddownthepaper guideflap(6)andinsert thepaperstackasfaras itwill go.
	Theconnectingcableis notconnectedcorrectly.	Ensure t hatthemains plugisinthemains socket
	ThesocketisnotliveCheckthedomesticfuses
	Thedeviceisfaulty.	N otifyCustomerServices.
TheOverheating/ OverloadstatusLED(15) islitupred.	Too m uchpaperhasbeen insertedorithasbeen drawninatanangle.	Followthestepsin 4.5Forward/reverse modesandclearthe paperjam.
	Thedevicehasbecome toohot.	Switchthedeviceoffand allowittocooldownforat least60minutes.
TheContainerLED(14)is litupred.	Thecollectingcontainer (7)isfull.	Emptythecontainer (7)asdescribedin5.1 Emptyingthecontainer.
Thecuttingrollers continuetorunafterthe shreddingprocesshas beencompleted.	There i s jammedpaperin theintakeshaft(1)/(2).	Followthestepsas describedin4.5 Forwards/ b a c k w a r d s modes. S witchoffthe machine a ndcheckfor piecesofpaperstuckin theintakeshaft.

7.Technical data

Inputvoltage220-240V~
Mainsfrequency50Hz
Max.powerconsumption80W
Dimensions (W x H x D)	37.0 x 52.3 x 26 cm
Weight(net)	7600g
Weight(gross)	8900g
Basketcapacityforpaperandplasticcards	25litres
Noiselevelwhenidling	< 6 0 dB
Max. cutting performance - paper (70 gsm)	6 sheets (DIN A4 paper)* manual125sheets(DINA4paper)*auto
Max. cutting performance - paper (80 gsm)	5 sheets (DIN A4 paper)* manual120sheets(DINA-4 p aper)*auto
Max.cuttingperformance- p lasticcards	1
Max.cuttingspeed	1.8m/min.manual2.2m/min.auto
Max. feed width for paper / plastic cards	225 mm
Cutting size for paper / plastic cards	4 x 20 mm
Max. constant operation time	8 minutes manual60minutesauto
Nominalrestperiod	60minutes
Protectionclass(asperDIN66399)	2
Safety levels (as per DIN 66399)	P-4 / T-4 / E-3

* Thicker paper, moisture or any voltage other than that permitted may reduce the performance.

8.Warrantydisclaimer

All of the technical information, data and instructions regarding operation contained in these operating instructions was up to date at the time of printing and disprovided based on previous experience and to the best of our knowledge.

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe theoperatinginstructionsand/or safetynotes.

Maschinenaufbau

1. Voyantd'état LED desurchauffe/Surcharge

86652Monheim/Germany

Service& Support

QR code image containing encoded data, no visible human-readable text

support.hama.com/00050591

[phone]

D GB

CE