PBKP 8000 A1 - Water pump PARKSIDE - Free user manual and instructions

USER MANUAL PBKP 8000 A1 PARKSIDE

Industrial pump or motor device with green and black casing, mounted on a black platform (no visible text or symbols)

PDF ONLINE www.fid-service.com

PETROL CLEAR WATER PUMP - PBKP 8000 A1 BENZIN-KLARWASSERPUMPE - PBKP 8000 A1 POMPE À EAU CLAIRE À ESSENCE - PBKP 8000 A1

GBIENICYMT

PETROL CLEAR WATER PUMP

Operating and Safety Instructions

Translation of the original operating instructions

FR CH BE

Before reading, unfold the page with the illustrations and then familiarise yourself with all the functions of the product.

DE AT CH

GB / IE / NI / CY / MT Operating and Safety Instructions Page 1

1 Explanation of the symbols on the product.... 2
2 Introduction.... 3
3 Product description (Fig. 1-10).... 3
4 Scope of delivery (Fig. 2) 3
5 Proper use.... 3
6 Safety instructions 4
7 Technical data 5
8 Unpacking.... 6
9 Before commissioning 6
10 Operation 8
11 Cleaning and maintenance 8
12 Storage 9
13 Transport.... 10
14 Repair & ordering spare parts.... 10
15 Disposal and recycling 10
16 Maintenance plan.... 11
17 Troubleshooting.... 11
18 EU Declaration of Conformity.... 12
19 Warranty certificate.... 13
20 Exploded view.... 150

1 Explanation of the symbols on the product

Symbols are used in this manual to draw your attention to potential hazards. The safety symbols and the accompanying explanations must be fully understood. The warnings themselves will not rectify a hazard and cannot replace proper accident prevention measures.

	Before commissioning, read and observe the operating manual and safety instructions!	[G72G]	Direction of rotation of the pump
	Attention! Failure to observe the safety signs and warning information affixed to the product and failure to observe the safety and operating manual can result in serious injury or even death.		Tank contents
	Wear hearing protection. Fuel-oil mixture
	Naked flames or smoking near the device is strictly prohibited!		Flow rate per hour
	No naked flames. Max. fluid temperature
	Danger of poisoning! Only use the product outdoors and never in closed or poorly ventilated rooms.		Max. pressure delivered
	Important. Always switch off the engine before refuelling. Do not refill during operation.	[SZYT]	Weight kg
	Choke ON/OFF		Guaranteed sound power level of the product.
	Press the primer.		The product complies with the applicable European directives.
	Flow rate speed - Low-High

2 Introduction

Manufacturer:

Scheppach GmbH

Günzburger Straße 69

D-89335 Ichenhausen

Dear Customer

We hope your new product brings you much enjoyment and success.

Note:

In accordance with the applicable product liability laws, the manufacturer of this product assumes no liability for damage to the product or caused by the product arising from:

• Improper handling
  • Non-compliance with the operating manual
  • Repairs carried out by third parties, unauthorised specialists
  • Installing and replacing non-original spare parts
• Improper use

Note:

Read the whole text of the operating manual before assembly and commissioning.

This operating manual should help you to familiarise yourself with your product and to use it for its intended purpose.

The operating manual includes important instructions for the safe, proper and economic operation of the product, for avoiding danger, for minimising repair costs and downtimes and for increasing the reliability and extending the service life of the product.

In addition to the safety instructions in this operating manual, you must also observe the regulations applicable to the operation of the product in your country.

Keep the operating manual package with the power tool at all times and store it in a plastic cover to protect it from dirt and moisture. They must be read and carefully observed by all operating personnel before starting the work.

The product may only be used by personnel who have been trained to use it and who have been instructed with respect to the associated hazards.

In addition to the safety instructions in this operating manual and the separate regulations of your country, the generally recognised technical rules relating to the operation of such products must also be observed.

We accept no liability for accidents or damage that occur due to a failure to observe this manual and the safety instructions.

3 Product description (Fig. 1-10)

1. Water filler port
2. Spark plug connector
   2a. Spark plug
3. Choke
   3a. Fuel pump "primer"
4. Exhaust pipe
5. Pull starter
6. Fuel tank
7. Fuel filler cap
8. Wing screw
9. Air filter cover
   9a. Air filter
10. Suction connection
11. Off switch
12. Pressure connection
13. Throttle
14. Water drain plug
15. Hose adapter
16. Union nut
17. Seal
18. Hose clamps
19. Pre-filter
20. Spark plug wrench

4 Scope of delivery (Fig. 2)

Item Quantity Designation

15 2 x Hose adapter
16 2 x Union nut
17 2 x Seal
18 3 x Hose clamp
19 1 x Pre-filter
20 1 x Spark plug wrench
1 x Operating manual

5 Proper use

The product is suitable for watering and irrigating green areas, vegetable beds and gardens and for operating lawn sprinklers. Suitable pumping media are clear water (fresh water), rainwater and light detergent/soap solutions. With a pre-filter, water can be drawn from ponds, streams, rainwater barrels, rainwater cisterns and wells. The maximum temperature of the pumped liquid must not exceed +35°C in continuous operation.

The product may only be used in the intended manner.

Any use beyond this is improper. The user/operator, not the manufacturer, is responsible for damages or injuries of any type resulting from this.

An element of the intended use is also the observance of the safety instructions, as well as the assembly instructions and operating information in the operating manual.

Persons who operate and maintain the product must be familiar with the manual and must be informed about potential dangers.

The liability of the manufacturer and resulting damages are excluded in the event of modifications of the product.

The product may only be operated with original parts and original accessories from the manufacturer.

The safety, operating and maintenance specifications of the manufacturer, as well as the dimensions specified in the technical data, must be observed.

Please note that our products were not designed with the intention of use for commercial or industrial purposes.

We assume no guarantee if the product is used in commercial or industrial applications, or for equivalent work.

WARNING

For your own safety, please thoroughly read this manual and the general safety instructions before turning the product on. If you give the product to third parties, always include these usage instructions.

5.1 Improper use

The use of the pump is strictly prohibited for the following substances:

• Paints and varnishes of all kinds
- All types of solvents or thinners
- All types of fuels or lubricants
• Propane or other liquefied gases
- Flammable liquids of all kinds
- Food for people and animals
- Granules or substances with solid particles
- Chemicals
• Liquids with temperatures above 40°C
- All liquids not explicitly referred to in this manual
- Liquids with anti-parasites, herbicides and pesticides.

Follow the safety instructions

ATTENTION

The pump must not be used for filling containers which may explode under excess pressure.

• The pump is not suitable as a safety device for fire extinguishing systems.
• The pump is not suitable for continuous operation (e.g. industrial use, continuous circulation operation).
• The pump is approved exclusively for use in pumping water and neutral liquids at room temperature.

Explanation of the signal words in the operating manual

DANGER

Signal word to indicate an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Signal word to indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Signal word to indicate a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.

ATTENTION

Signal word to indicate a potentially hazardous situation which, if not avoided, could result in product or property damage.

6 Safety instructions

ATTENTION

Attention!

When using products, several safety warnings must be observed to prevent injuries and damage. For this reason, please carefully read this operating manual / safety instructions. If you hand the product over to another person, please hand over this operating manual / safety instructions as well. We accept no liability for accidents or damage that occur due to a failure to observe this manual and the safety instructions.

Follow the safety instructions

Keep all safety information and instructions for future reference!

6.1 Product-specific safety instructions

• Place the product on a level, even surface (such that it cannot topple).
• Check the entire product for loose parts (nuts, bolts, screws, etc.). Service or replace if necessary before using the product.

ATTENTION

For your own safety, only use accessories and additional equipment that are indicated in the operating manual or have been recommended or indicated by the manufacturer. Use of other tools or accessories that those recommended in the operating manual or in the catalogue could represent a personal danger to you.

• People should keep a safe distance of at least 15 metres from the work area.
• Do not use the product if it is damaged. Never remove protective devices from the product. This can result in serious injuries.
• Children are not permitted to use the product. Children should be supervised in order to ensure that they do not play with the product.
• Do not leave the product unattended.
  • People under the influence of alcohol, drugs and medication, as well as those who are tired or ill.

6.2 Handling fuel

DANGER

Risk of fire and explosion!

When filling, fuel may ignite and even explode. This can lead to severe burns or death.

• Only store fuel in containers (canisters) designed for this purpose.
• The tank caps must always be properly screwed on and tightened.
• Fuel must be filled before starting the engine. While the engine is running or immediately after switching off the product, do not open the fuel filler cap or add fuel.
• Before refuelling, switch off the combustion engine and let it cool down.
• Refuel outdoors only and do not smoke while refuelling.
• Never store the product with fuel in the tank inside a building. Any fuel vapours produced can come into contact with naked flames or sparks and ignite.
• Do not place the product and fuel tank near heaters, radiant heaters, welding machines or other sources of heat.
• If fuel has overflowed, do not start the combustion engine until the area contaminated with fuel has been cleaned. Avoid starting the engine until the fuel vapours have evaporated (wipe dry).
• For safety reasons, check fuel line, fuel tank, fuel cap and connections regularly for damage, ageing (brittleness), tight fit and leaks and replace if necessary.

6.3 Residual risks

The product has been built according to state-of-the-art and the recognised technical safety rules. However, individual residual risks can arise during operation.

• Residual risks can be minimised if the "Safety Instructions" and the "Intended Use" together with the operating manual as a whole are observed.
• Use the product in the way that is recommended in this operating manual. This is how to ensure that your product provides optimum performance.
• Prevent the product being unintentionally started up.
• Keep your hands away from the working area when the product is in operation.
• Comply with the stipulated maintenance and safety instructions in the operating manual.
  • Furthermore, despite all precautions having been met, some non-obvious residual risks may still remain.

7 Technical data

Engine 2-Stroke engine / air cooled
Displacement 42.7 cm3
Max. Output power (kW) 1.25 kW / 1.7 HP
Max. engine speed 9500 rpm
Max. flow rate in l 8000 l/h
Nominal flow rate in l 5500 l/h
Suction connection	G1"
Pressure connection	G1"
Tightening torques for screws	8 Nm
Tightening torques for inlet and outlet connection ports	8-10 Nm
Max. delivery height	25-30 m
Max. suction height	8 m
Max. pressure	3 bar
Fuel	Mixture 1:40
Tank contents	1.05 l
Dimensions	425x255x315 mm
Weight	8.5 kg

Subject to technical changes!

Noise and vibration

WARNING

Noise can have serious effects on your health. If the machine noise exceeds 85 dB, please wear suitable hearing protection for you and persons in the vicinity.

The noise emission values have been determined in accordance with EN ISO 3744:1995.

Noise data

Sound pressure level L_pA	96 dB
Measurement uncertainty K_pA	3 dB
Sound power level L_wA	109 dB
Measurement uncertainty K_wA	3 dB
Guaranteed sound power level L_wA	112 dB

If necessary, adhere to rest periods and limit the duration of work to the bare minimum.

8 Unpacking

• Open the packaging and carefully remove the product.
• Remove the packaging material, as well as the packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport damage. Immediately report any damage to the transport company that delivered the Product. Later claims will not be recognised.
• If possible, keep the packaging until the expiry of the warranty period.
• Familiarise yourself with the product by means of the operating manual before using for the first time.
• With accessories as well as wearing parts and replacement parts use only original parts. Spare parts can be obtained from your specialist dealer.
• When ordering please provide our article number as well as type and year of manufacture for the product.

WARNING

The product and the packaging material are not children's toys!

Do not let children play with plastic bags, films or small parts! There is a danger of choking or suffocating!

9 Before commissioning

WARNING

Health hazard!

Inhalation of fuel / lubricating oil vapours and exhaust gases can cause serious damage to health, unconsciousness and in extreme cases death.

• Do not breathe fuel / lubricating oil vapours and exhaust gases.
• Operate the product outdoors only.

* = not included in the scope of delivery!

Note:

The product has a centrifugal clutch. This creates a frictional connection as the speed increases by pressing the clutch facings against the inner wall of the clutch housing due to the centrifugal force.

Check before operation

• Check all sides of the engine for oil or fuel leaks.
• Check the fuel level – the fuel tank should be at least half-full.
• Check the condition of the air filter.
• Check the condition of the fuel lines.
• Look for signs of damage.
• Check that all protective covers are in place and all screws, nuts and bolts are tightened.
• Ensure that the product is sufficiently ventilated.
• Make sure that the spark plug connector is attached to the spark plug.
• The suction and pressure lines must be installed in such a way that they do not exert any mechanical pressure on the pump.

9.1 Installation of the suction line\* (Fig. 3)

Note:

The pump has a non-return valve which prevents the water from flowing back into the suction line.

• The suction line* must be reinforced with rigid walls or wire mesh.
• Do not use a hose* that is smaller than the suction line* of the pump.
• The suction line* should only be as long as necessary.
• Pumping performance is best when the pump is as close to the surface of the water as possible and the hoses* are short.

• A leaking suction line* will prevent the water from being sucked in due to air ingress.

• Insert the hose adapter (15) into the union nut (16).

• Insert the seal (17) into the union nut (16).
• Screw a union nut (16) onto the suction connection (10) and tighten it firmly (8 - 10 Nm). Make sure that the seal (17) of the union nut (16) is in contact with the suction connection (10).

• Attach the suction line* to the hose adapter (15) of the suction line* with a hose clamp (18) to avoid air leakage and loss of suction power. Use the Phillips screwdriver on the spark plug spanner (20) to tighten the hose clamp (18).

• Fit the pre-filter (19) to the other end of the suction line* and fasten it with a hose clamp (18). Use the Phillips screwdriver on the spark plug spanner (20) to tighten the hose clamp (18). Avoid sucking in foreign bodies (sand etc.). If necessary, fit a pre-filter (19).

• Disassembly takes place in reverse order.

9.2 Installation of the pressure line\* (Fig. 4)

1. Insert the hose adapter (15) into the union nut (16).
2. Insert the seal (17) into the union nut (16).
3. Screw a union nut (16) onto the pressure connection (12) and tighten it firmly (8-10 Nm). Make sure that the seal of (17) the union nut (16) is in contact with the pressure connection (12).
4. To improve pump performance and reduce fluid friction, use a short, large diameter pressure line*. A long or thin hose* increases fluid friction and reduces pumping performance.
5. Attach the pressure line* to the hose adapter (15) of the pressure line* with a hose clamp (18). Tighten the hose clamp (18) firmly with the Phillips screw-driver on the spark plug wrench (20) to prevent the pressure line* from slipping off the hose adapter (15) under pressure.
6. Disassembly takes place in reverse order.

9.3 Priming the product with water (Fig. 5)

Note:

Dry operation of the pump will cause damage to the pump seals. If the pump runs dry, switch off the engine immediately and let the pump cool down before priming with water.

Note:

If the pump is removed after use, it is essential to fill up with water again when it is reconnected and put into operation.

1. Before starting the engine, remove the water filling plug (1) from the pump chamber and fill the pump chamber with water.
2. Screw in the water filling plug (1) again and tighten it firmly.

Note:

Filling the suction line with water is not necessary!

9.4 Check the level of the fuel/oil mixture (Fig. 6)

DANGER

Risk of fire and explosion!

When filling, fuel may ignite and even explode. This can lead to severe burns or death.

• Switch off the engine and let it cool down.
  • Always use fresh fuel/oil mixture.
• Keep heat, flames and sparks away.
• Only fill up with fuel outdoors.
• Wear protective gloves.
• Avoid contact with skin and eyes.
• Start the product at a distance of at least 3 m from the fuel filling point.
• Watch out for leaks. If fuel is leaking, do not start the engine.
• Use a suitable funnel or filler pipe for refuelling so that no fuel can spill onto the combustion engine and housing.

Do not overfill the fuel tank!

1. Check the fuel level.
2. The fuel level must be between MAX and MIN.
3. Add fuel if the fuel level is too low.
   – Pay attention to the correct mixing ratio!
4. Unscrew the fuel filler cap (7). The fuel filler cap (7) is connected to an anti-loss device in the fuel tank (6) and thus cannot fall off.

9.4.1 Filling up fuel/oil mixture

Fuel and 2-stroke oil

Special 2-stroke oil for air-cooled 2-stroke engines with a mixing ratio of 1:40 must be used.

WARNING

Do not use fuel that has not been correctly mixed with 2-stroke oil. This may cause permanent engine damage and will void the manufacturer's warranty on this product. Never use a fuel mixture that has been stored for more than 90 days.

9.4.1.1 Fuel mixture

Do not mix the fuel mixture in the tank.

Add the 2-stroke oil in accordance with the fuel mixture table.

Fuel 2-stroke engine oil (1:40)
1 litre 0.025 litres
2 litres 0.050 litres
5 litres 0.125 litres

10 Operation

10.1 Start the engine (Fig. 8)

DANGER

Danger of poisoning!

Only use the product outdoors and never in closed or poorly ventilated rooms.

ATTENTION

• Do not let the pull starter whip back in. This can result in damage.
  – In case of cool weather, it may be necessary to repeat the starting process numerous times.

NOTE

Only use the fuel pump "primer" when the engine is cold!

NOTE

If the engine is being started for the first time, several tries are required to start until the fuel has been delivered from the tank to the engine.

When the engine is "cold":

1. Set the "CHOKE" (3) to the position.
2. In colder temperatures, press the fuel pump "primer" (3a) several times. This makes it easier to start the engine.
3. Now pull the pull starter (5) and the engine should start. If the engine does not start, repeat the process.
4. Once the engine is started (after approx. 15-30), move the "CHOKE" (3) from the position to the position (Fig. 8).

5. Use the throttle to set the required speed (13). This is how you increase or decrease the delivery rate. L = Engine at idle speed H = Maximum delivery rate

6. If the engine does not start even after several attempts, read the "Troubleshooting" chapter.

When the engine is "warm":

1. Now pull the pull starter (5) quickly. The product should start after 2 pulls. If the product has still not started, repeat the procedure described under.
2. Use the throttle to set the required speed (13).

Note:

Let the engine warm up at idle for about 10 minutes.

10.2 Switch off the engine (Fig. 1)

Note:

Allow the product to run for a short time (approx. 30 seconds) switching it off so that the engine can cool down.

1. To switch off the engine, press the off switch (11).
2. Disconnect the spark plug connector (2) from the spark plug (2a) to prevent the engine from restarting.

10.3 After work

* = not included in the scope of delivery!

1. Remove the pressure line*.
2. Remove the suction line*.
3. Unscrew the water drain plug (14) and let the water flow out of the pump chamber.
4. Refit the water drain plug (14).

11 Cleaning and maintenance

WARNING

Have maintenance and repair tasks that are not described in this operating manual, carried out by a specialist workshop. Use only original spare parts.

There is a risk of accident! Always carry out maintenance and cleaning work when the engine is switched off. There is a danger of injury! Let the Product cool down before all maintenance and cleaning tasks. Elements of the engine are hot. There is a danger of injury and burning!

The product can start unexpectedly and cause injuries.
- Switch off the engine before carrying out any cleaning or maintenance work.
- Disconnect the spark plug connector from the spark plug.
- Allow the engine to cool down.

11.1 Cleaning

• Keep protective devices, air vents and the motor housing as free of dust and dirt as possible. Rub the product clean with a clean cloth or blow it off with compressed air at low pressure. We recommend that you clean the product directly after every use.
• Clean the product at regular intervals using a damp cloth and a little soft soap. Do not use any cleaning products or solvents; they could attack the plastic parts of the product. Make sure that no water can penetrate the product interior.

11.2 Maintenance

11.2.1 Cleaning the air filter (9a) (Fig. 9)

ATTENTION

Risk of damage!

Operating the engine without a filter element or with a damaged filter element can cause engine damage.

- Never run the engine without the air filter element or with a damaged filter element. This would allow dirt into the engine, which would result in severe damage to the engine.

Clean the air filter (9a) every 50 operating hours, replace if necessary.

1. Remove the wing screw (8).
2. Remove the air filter cover (9). Pay attention to the lug on the air filter cover (9).
3. Remove the air filter (9a).
4. Do not use harsh cleaners or petrol to clean the filter.
5. Clean the elements by knocking them out on a flat surface. If heavily soiled, wash with soapy water, then rinse with clean water and allow to air dry.
6. The re-assembly takes place in reverse order.

11.2.2 Cleaning the spark plug (2a) (Fig. 10)

ATTENTION

Only replace the spark plug when the engine is cold!

Check the spark plug for dirt for the first time after 20 operating hours and clean it with a copper wire brush if necessary. Then service the spark plug every 50 operating hours.

1. Pull the spark plug connector (2) off carefully. Do not pull on the cable, but directly on the plug.
2. Remove the spark plug (2a) with the enclosed spark plug wrench (20).
3. Remove any dirt from the base of the spark plug (2a).
4. Visually inspect the spark plug (2a). Remove any deposits present using a wire brush.
5. Check the spark plug gap. Set the electrode gap to 0.6 to 0.7 mm with a feeler gauge.
6. The re-assembly takes place in reverse order.

NOTE

A loose spark plug can overheat and cause damage to the engine. Tightening the spark plug too much can damage the thread in the cylinder head.

12 Storage

DANGER

Risk of fire and explosion!

Storing the product near potential sources of ignition can result in a fire or an explosion. This can lead to severe burns or death.

- Eliminate possible sources of ignition, such as furnaces, hot water boilers with gas, gas dryers, etc.

ATTENTION

Risk of damage!

If the product is not stored properly, the engine can be damaged.

- Store the product protected against dirt, dust and moisture.

12.1 Preparation for storage

WARNING

Do not remove the fuel in enclosed spaces, near fire or when smoking. Petrol fumes can cause explosions and fire.

1. Clean and check the product for damage.
2. Empty the fuel tank using a petrol extraction pump (not included in the scope of delivery) into a collection container.
3. Start the engine and let it run until the remaining fuel is used up.
4. Store fuel in tanks specifically designed for this purpose.
5. Remove the spark plug (2a) and clean it as described in 11.2.2.
6. Pour 1 teaspoon of clean 2-stroke oil into the combustion chamber. Pull the starter rope slowly several times to coat internal components.
7. Screw the spark plug (2a) back in (Fig. 10).
8. Store the product in a well-ventilated place or area.

12.2 Drain fuel/oil mixture with a fuel extraction pump (Fig. 7)

In case of storage over a longer period of time, the fuel must be drained.

1. Hold a collection bucket under the hose of the fuel extraction pump (not included in the scope of delivery).

2. Unscrew the fuel filler cap (7). The fuel filler cap (7) is connected to an anti-loss device in the fuel tank (6) and thus cannot fall off.

3. Push the hose of the fuel extraction pump into the fuel tank (6) and drain out the fuel/oil mixture completely using the fuel extraction pump.

4. Retighten the fuel filler cap (7).

13 Transport

Preparation for transport

1. Empty the fuel tank using a petrol extraction pump (not included in the scope of delivery) into a collection container.
2. If operational, keep the engine running until the remaining fuel has been used up.
3. Remove the spark plug connector from the spark plug.
4. Secure the product against slipping using a tension strap, for example.
5. The product can be lifted and moved via the handle.

14 Repair & ordering spare parts

After repairs or maintenance, make sure that all safety-related parts are installed and are in perfect condition. All parts which may cause injury must be kept where they are inaccessible to children or others.

ATTENTION

According to the German Product Liability Act, no liability is accepted for damage caused by improper repairs or by not using original spare parts.

Such work should be performed by a customer service centre or an authorised specialists. The same applies to accessory parts.

Connections and repairs

Connections and repair work on the electrical equipment may only be carried out by electricians.

NOTE

Important note in the case of repairs

When returning the product for repair, for safety reasons, ensure that it is free of oil and fuel when it is sent to the service centre.

14.1 Ordering spare parts

Please provide the following information when ordering spare parts:

• Model designation
• Item number
• Type plate data

Spare parts / accessories

Sealing ring 30x20x3,6 - Item number:	3914601001
Adapter - item number: 391	4601002
Union nut - item number: 39	914601003

14.2 Service information

With this product, it is necessary to note that the following parts are subject to natural or usage-related wear, or that the following parts are required as consumables.

Wearing parts*: Spark plug, air filter

* = not included in the scope of delivery!

Spare parts and accessories can be obtained from our Service Centre. To do this, scan the QR code on the front page.

15 Disposal and recycling

Notes for packaging

The packaging materials are recyclable. Please dispose of packaging in an environmentally friendly manner.

You can find out how to dispose of the disused device from your local authority or city administration.

Fuels and oils

• Before disposing of the product, the fuel tank and the engine oil tank must be emptied!
• Fuel and engine oil do not belong in household waste or drains, but must be collected or disposed of separately!
• Empty oil and fuel tanks must be disposed of in an environmentally friendly manner.

16 Maintenance plan

Always comply with the following maintenance intervals in order to ensure problem-free operation. Attention! The fuel/oil mixture must be filled in before the device is used for the first time.

Component Before		every use	Every 3 months or 20h	Every 6 months or 50h	Every 12 months or 100h	Every 2 years or 300h
Checking the air filter	Check X
	Clean X
Spark plug Check	and adjust X X X
	Replace X
Spark plug connector	Clean X
Cooling fins Test X
Fasteners such as screws and nuts	Check (tighten if necessary)	X
Seals of the connecting elements	Check and replace if necessary				X
Idle Check and adjust				X
Combustion chamber	Clean X
Fuel/oil mixture	Check X
Fuel tank	Check				X
Fuel line	Check	Every year (replace if necessary)
	Attention: Have points “X” carried out only by an authorised specialist company.

17 Troubleshooting

The following table shows fault symptoms and describes remedial measures in the event of your product failing to work properly. If you cannot localise and rectify the problem with this, please contact your service workshop.

Troubleshooting during commissioning
Fault		Possible cause	Remedy
No ignition spark	Spark plug	Carbon deposit between the spark plug electrodes	Clean the spark plug.Set the electrode gap to 0.6 to 0.7 mm.Replace the spark plug.
	Other	Ignition coil defective, flywheel magnet too weak	Contact customer service for this.
Weak spark	Compression	Too much fuel in the combustion chamber, bad fuel or water in the tank	Remove spark plug and allow to dry, change fuel/oil mixture.

Troubleshooting during operation
Fault	Possible cause	Remedy
Engine does not come up to speed	Choke is in "Z" position	Set the choke to ≡.
	Movable elements worn out	Replace
	Exhaust system blocked, no air supply	Replace exhaust system, check or replace ignition coil.
	Ignition spark weak, cylinder head sooty Set the electrode gap to 0.6 to 0.7 mm.
Carburettor leaking	Carburettor gasket worn	Contact customer service for this.

18 EU Declaration of Conformity

Translation of the original Declaration of Conformity

Manufacturer:

Scheppach GmbH

Günzburger Straße 69

D-89335 Ichenhausen

We declare under our sole responsibility that the product described here complies with the applicable directives and standards.

Brand: Parkside

Art. designation: PETROL CLEAR WATER PUMP -

PBKP 8000 A1

Item No. 3914601974, 3914601980,

39146019915, 39146019959

IAN no. 440149 2304

Series no. 01001-04788

EU directives:

2014/30/EU, 2006/42/EC, 2000/14/EC_2005/88/EC, 2011/65/EU*

* The object of the declaration described above fulfils the regulations of the directive 2011/65/EU of the European Parliament and Council from 8th June 2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

2016/1628/EU

Emission. No:

e24*2016/1628*2021/1398SHA1/P*0521*00

Applied standards:

EN:809:1998/A1:2009; EN 61000-6-1:2007;

EN IEC 61000-6-1:2019; EN 55012:2007/A1:2009;

Documentation authorised representative:

David Rümpelein

Günzburger Str. 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

Warranty certificate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under the service number printed below. Please note the following terms under which guarantee claims can be made:

• These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee.

- Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The following are also excluded from our guarantee: compensation for transport damage, damage caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by the device being dropped) and normal wear resulting from proper operation of the device.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

- The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies when an on-site service is used.

- In order to assert your guarantee claim, please contact the service partner shown below. If the complaint is within the guarantee period, we will provide you with a return slip, with which you can return your defective device free of charge to us. It would help us if you could describe the nature of the problem in as much detail as possible. If the defect is covered by our guarantee then your device will either be repaired immediately and returned to you, or we will send you a new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.

Service-Hotline (GB):

00800 4003 4003

Service-Email (GB):

[e-mail]

Service Address (GB):

Forest Park & Garden

Coed Court, Taffsmead Road

Treforest, Ind. Estate, Pontypridd

CF375SW

Service-Hotline (IE):

00800 4003 4003

Service-Email (IE):

[e-mail]

Service Address (IE):

Forest Park & Garden

Coed Court, Taffsmead Road

Treforest, Ind. Estate, Pontypridd

CF375SW

Service-Hotline (NI):

00800 4003 4003

Service-Email (NI):

[e-mail]

Service Address (NI):

Forest Park & Garden

Coed Court, Taffsmead Road

Treforest, Ind. Estate, Pontypridd

CF375SW

Service-Hotline (CY):

00800 4003 4003

Service-Email (CY):

[e-mail]

Service Address (CY):

GEORGE C SOLOMONIDES & SON LTD

PO.BOX 56236 / 169, LEONTIOS A'

GR - 3305 LIMASSOL/CYPRUS

[e-mail]

At www.lidl-service.com you can download this and many more manuals, product videos plus installation software.

The QR code takes you directly to the Lidl service page (www.lidl-service.com) and you can open your operating manual by entering the article number (IAN) 440149_2304.

Inhaltsverzeichnis

Günzburger Straße 69

D-89335 Ichenhausen

Verehrter Kunde

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

Garantieurkunde

Service-Adresse (DE):

Scheppach GmbH

Günzburger Str. 69

DE - 89335 Ichenhausen

Service-Hotline (AT):

00800 4003 4003

[e-mail]

Service-Adresse (AT):

Gausch Hubert

Günzburger Straße 69

D-89335 Ichenhausen

Cher client,

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

Certificat de garantie

Chère Cliente, Cher Client,

Service-Hotline (BE):

00800 4003 4003

Service-Email (BE):

[e-mail]

Service Adresse (BE):

TeleMarCom European Services GmbH

Am Ziegelweiher 24

DE - 61130 Nidderau

Service-Hotline (CH):

00800 4003 4003

Service-Email (CH):

[e-mail]

Service Adresse (CH):

Klaus-Häberlin AG

Industriestraße 6

CH - 8610 Uster

Günzburger Straße 69

D-89335 Ichenhausen

Geachte klant,

10.1 Motor starten (afb. 8)

GEVAAR

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

Garantiebewijs

Geachte klant,

Service-hotline / Hotline du service (NL): Service-hotline (BE):

00800 4003 4003

00800 4003 4003

E-mailadres / Email du service (NL):

E-mailadres (BE):

[e-mail]

[e-mail]

Serviceadres / Adresse du service (NL):

Serviceadres (BE):

TeleMarCom European Services GmbH

TeleMarCom European Services GmbH

Am Ziegelweiher 24

Am Ziegelweiher 24

DE - 61130 Nidderau

DE - 61130 Nidderau

Günzburger Straße 69

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

Günzburger Straße 69

89335 Ichenhausen, Germania

Egregio cliente,

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

[e-mail]

Günzburger Straße 69

D-89335 Ichenhausen

Vážený zákazníku,

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

Záruční list

Važena zakaznice, važeny zakazniku,

Günzburger Straße 69

D-89335 Ichenhausen

Vážený zákazník,

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

Záručný list

Günzburger Straße 69

D-89335 Ichenhausen

Tisztelt Ügyfelünk!

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

JÓTÁLLÁSI TÁJÉKOZTATÓ

Günzburger Straße 69

D-89335 Ichenhausen

Szanowny Kliencie

Günzburger Straße 69

D-89335 Ichenhausen

Division Manager Product Center

Andreas Pecher

Head of Project Management

Gwarancja

Drodzy Klienci,

Günzburger Straße 69

D-89335 Ichenhausen, Tyskland

Kære kunde

Günzburger Straße 69

D-89335 Ichenhausen, Tyskland

Division Manager Product Center

Head of Project Management

Garantibevis

Kære kunde,

Exploded view diagram of a mechanical assembly with numbered components and exploded views

Notizen

CE

SCHEPPACH GMBH

Günzburger Str. 69

D-89335 Ichenhausen

FR RECO

FSC

www.fsc.org

MIX

Paper from responsible sources

C167024 C167024 C167024 C

FSC

www.fsc.org

MIXTE