Q: How to clean the blade of the PARKSIDE PBHS 650 A1 hedge trimmer?

Before starting the cleaning: Stop the motor by pressing the switch, wait for the cutting unit to come to a complete stop, remove the spark plug connector, and let the device cool down. Always wear protective gloves to avoid injuries when cleaning the blade. Cleaning the blade and cutting unit: Regularly clean the cutting unit using a brush or a dry cloth. This is essential: never pour water on the blade as it causes corrosion. Water, solvents, and polishing agents are prohibited. After each use, regularly clear the motor's air vents to prevent overheating of the device. Lubricating moving parts: Regularly clean and oil all moving parts of the cutting unit with environmentally friendly oil. Important: never use grease for the moving parts of the blade, as this could damage the cutting mechanism. Lubricating the transmission: Lubricate the transmission every 10 to 20 hours of service with a small amount of grease using the supplied grease pump. Open the lubrication opening screw (18) located under the hedge trimmer with the 4 mm hex key, apply a small amount of grease, and then screw it back in. Caution: perform light greasing and never over-grease. Checking and maintaining the blade: Check the condition of the edge before each use. Regularly check the sliding movement of the cutting unit. When the blade becomes dull, have it sharpened to restore its cutting efficiency. A worn blade reduces performance and can damage the motor. Cleaning the housing: Clean the housing with a soft-bristled brush or with a dry cloth only. Do not use any chemicals, water, or detergent that could damage the motor or electronic components.

Q: My PLEM 50 A1 rangefinder no longer displays measurements - what should I do?

Here are the checks to perform in order: 1. Check the battery status The PLEM 50 A1 operates with 2 AAA (LR03) batteries . A battery alert symbol appears on the LCD screen if the battery is low. Replace both batteries and check if the display reappears. 2. Restart the device Press the button 11 (On/Off) to turn off the rangefinder, wait 3 seconds, then turn it back on. The screen should display with the LCD backlight. 3. Check if an error code is displayed If you see a numerical code instead of measurements, refer to: Error 255 = Signal too weak. Use a target plate or white paper as a reflective surface. Error 256 = Signal too strong. Adjust the target surface or move slightly closer. Error 261 = Distance out of range. The range of the PLEM 50 A1 is 0.05 to 50 m . Move closer or further away according to your measurement. Error 220 = Low battery. Replace the batteries. Error 500 = Hardware issue. Repeat steps 1 and 2 then test again. 4. Check the laser alignment Ensure that the laser beam (red dot) is properly emitted from the device and is aimed at the surface to be measured. In low light, the laser spot may be difficult to see. If after these steps the screen remains blank and no error code is displayed, the device may have an electronic fault.

Q: How to clean the spark plug and the carburetor?

Cleaning the spark plug Maintenance intervals: Check the fouling of the spark plug for the first time after 10 hours of operation, then every 50 hours of operation. If it is fouled, clean it with a copper brush. Procedure: Disconnect the spark plug connector (part 7a) by turning it Remove the spark plug using a spark plug wrench Clean the spark plug with a copper brush if it shows signs of fouling Set the electrode gap to 0.75 mm using a feeler gauge Reinstall the spark plug without overtightening Reconnect the spark plug connector Cleaning the carburetor The manual recommends specialized maintenance for the carburetor. However, you can perform basic cleaning: Before any intervention: Make sure to disconnect the spark plug connector and let the engine cool down. Procedure: Completely empty the fuel tank using a fuel siphon pump (it is necessary for this operation) Access the carburetor (part 14) located under the air filter cover Open the carburetor drain screw (part 14) with a 10 mm wrench , placing a collection pan underneath to catch residual fuel Let the fuel drain completely from the carburetor Close the screw once the carburetor is emptied Important: For a thorough cleaning of the carburetor or in case of persistent operational issues (difficult starting, engine stalling), it is highly recommended to entrust this operation to an authorized specialized workshop, as it is a complex intervention that requires disassembly and complete cleaning of the fuel system.

Q: What is the replacement blade for the PARKSIDE PBRM 39 C2 lawn mower and how do I replace it?

The reference of the blade for your PARKSIDE PBRM 39 C2 lawn mower is n° 7911200630 . You can order it from Parkside spare parts dealers. Replacement Steps First, empty the fuel tank Hold the blade with one hand Unscrew the fixing screw (n° 20) counterclockwise Remove the washer and install the new blade in reverse order Tighten the screw to a torque of 45 Nm Important: Sharpening and balancing of the blade must be done at an authorized Parkside service center to ensure proper balance and avoid vibrations. Never attempt to straighten a bent blade - it must be replaced.

Q: What is the Ian code of the PARKSIDE PRM 1800 A2?

The Ian code of the PARKSIDE PRM 1800 A2 is: 373339_2104 This code is the unique identifier of the product and can be used to find spare parts, check warranty information, or any additional documentation from the manufacturer.

Question 1

How to clean the blade of the PARKSIDE PBHS 650 A1 hedge trimmer?

Accepted Answer

Before starting the cleaning: Stop the motor by pressing the switch, wait for the cutting unit to come to a complete stop, remove the spark plug connector, and let the device cool down. Always wear protective gloves to avoid injuries when cleaning the blade.

Cleaning the blade and cutting unit: Regularly clean the cutting unit using a brush or a dry cloth. This is essential: never pour water on the blade as it causes corrosion. Water, solvents, and polishing agents are prohibited. After each use, regularly clear the motor's air vents to prevent overheating of the device.

Lubricating moving parts: Regularly clean and oil all moving parts of the cutting unit with environmentally friendly oil. Important: never use grease for the moving parts of the blade, as this could damage the cutting mechanism.

Lubricating the transmission: Lubricate the transmission every 10 to 20 hours of service with a small amount of grease using the supplied grease pump. Open the lubrication opening screw (18) located under the hedge trimmer with the 4 mm hex key, apply a small amount of grease, and then screw it back in. Caution: perform light greasing and never over-grease.

Checking and maintaining the blade: Check the condition of the edge before each use. Regularly check the sliding movement of the cutting unit. When the blade becomes dull, have it sharpened to restore its cutting efficiency. A worn blade reduces performance and can damage the motor.

Cleaning the housing: Clean the housing with a soft-bristled brush or with a dry cloth only. Do not use any chemicals, water, or detergent that could damage the motor or electronic components.

Question 2

How to replace the sanding sheet on the PARKSIDE XQ2 sander?

Accepted Answer

The sanding sheet easily attaches to the support plate of the PARKSIDE XQ2 thanks to a Velcro-type hook-and-pile system. This system allows for quick and simple changes of abrasives according to your needs.

Before you begin: Always unplug the device from the power outlet before replacing the sanding sheet. Do not perform any maintenance or change the sheet while the device is running.

Steps to replace the abrasive:

Simply pull the worn sanding sheet to remove it from the support plate
Position a new sanding sheet on the plate by pressing it firmly so that the hook-and-pile system holds it well
Ensure that the sheet is properly attached over the entire surface of the plate before plugging the device back in

Available grits: Your PARKSIDE XQ2 sander comes with 6 sanding sheets: 2 sheets of grit 60 (coarse sanding), 2 sheets of grit 80 (medium sanding), and 2 sheets of grit 100 (fine sanding). Choose the appropriate grit for your work: use grit 60 for roughing or stripping, grit 80 for standard sanding of wood or plastic, and grit 100 for fine abrasion and finishing.

Important advice: Change the sanding sheet at the right time to achieve the best results. Avoid sanding very different materials (for example, metal and wood) with the same sheet, as this reduces the effectiveness of the abrasive and may alter the quality of the finish. Only use the device with a sanding sheet attached.

Question 3

How to top up or change the oil of the PARKSIDE PBRM 39 E4 lawn mower engine?

Accepted Answer

Your Parkside PBRM 39 E4 mower is equipped with a 4-stroke engine that requires regular oil maintenance to operate correctly. The engine holds 0.4 liters of oil and you must use only SAE 10W-40 engine oil. A complete oil change should be performed before the start of each season, while the engine is warm but stopped.

Before you begin, prepare your workstation: place the mower on a flat, solid surface, equip yourself with an oil suction pump with hose, an oil dipstick (part no. 9), a clean, lint-free cloth, and a flat recovery pan to collect the used oil. Wear gloves and work outdoors or in a well-ventilated area, as oil vapors are toxic and hazardous to health.

To check the oil level: unscrew the oil dipstick by turning it to the left, wipe it completely with a clean cloth, reinsert it without screwing it back in, then remove it again and check the level while holding it horizontally. The level should be between the MAX and MIN marks on the dipstick. Once the check is done, screw the dipstick back in tightly.

To perform a complete oil change: unscrew the oil dipstick (part no. 9) by turning it to the left. Insert the hose of the oil suction pump into the filling tube and suck all the used engine oil into the recovery pan. Then pour in about 0.4 liters of new SAE 10W-40 oil through the same tube, and then check the level as described above.

Important warnings: never top up or change the oil while the engine is running or immediately after stopping (wait a few minutes for the engine to cool down). Collect all used oil in a suitable container and dispose of it according to local regulations. Immediately wipe up any accidental spills with a cloth and dispose of it properly. Never fill with another type of oil: using an unsuitable oil will damage the engine and void your 3-year warranty. If you are not comfortable with this operation, have it done by an authorized specialized workshop.

Question 4

Where can I find the complete technical manual for the PBH 800 A1 hammer drill?

Accepted Answer

The PDF of this technical notice contains the complete specifications of the PBH 800 A1: rated power 800 W, impact frequency 0-7500 min-1, impact energies, drilling capacities (13 mm in steel, 24 mm in wood, 19 mm in concrete), and a detailed description of each component (function selector 4 modes, SDS-plus tool holder, quick-release chuck, lock button).

To access the detailed exploded diagrams showing the assembly and disassembly of all components, refer to the complete PDF file available on this page. The manufacturer's technical manual PARKSIDE also describes the four operating modes (drilling, hammer drilling, chiseling, chisel adjustment) with detailed illustrations.

Question 5

My PLEM 50 A1 rangefinder no longer displays measurements - what should I do?

Accepted Answer

Here are the checks to perform in order:

1. Check the battery status

The PLEM 50 A1 operates with 2 AAA (LR03) batteries. A battery alert symbol appears on the LCD screen if the battery is low. Replace both batteries and check if the display reappears.

2. Restart the device

Press the button 11 (On/Off) to turn off the rangefinder, wait 3 seconds, then turn it back on. The screen should display with the LCD backlight.

3. Check if an error code is displayed

If you see a numerical code instead of measurements, refer to:

Error 255 = Signal too weak. Use a target plate or white paper as a reflective surface.
Error 256 = Signal too strong. Adjust the target surface or move slightly closer.
Error 261 = Distance out of range. The range of the PLEM 50 A1 is 0.05 to 50 m. Move closer or further away according to your measurement.
Error 220 = Low battery. Replace the batteries.
Error 500 = Hardware issue. Repeat steps 1 and 2 then test again.

4. Check the laser alignment

Ensure that the laser beam (red dot) is properly emitted from the device and is aimed at the surface to be measured. In low light, the laser spot may be difficult to see.

If after these steps the screen remains blank and no error code is displayed, the device may have an electronic fault.

Question 6

How to clean the spark plug and the carburetor?

Accepted Answer

Cleaning the spark plug

Maintenance intervals: Check the fouling of the spark plug for the first time after 10 hours of operation, then every 50 hours of operation. If it is fouled, clean it with a copper brush.

Procedure:

Disconnect the spark plug connector (part 7a) by turning it
Remove the spark plug using a spark plug wrench
Clean the spark plug with a copper brush if it shows signs of fouling
Set the electrode gap to 0.75 mm using a feeler gauge
Reinstall the spark plug without overtightening
Reconnect the spark plug connector

Cleaning the carburetor

The manual recommends specialized maintenance for the carburetor. However, you can perform basic cleaning:

Before any intervention: Make sure to disconnect the spark plug connector and let the engine cool down.

Procedure:

Completely empty the fuel tank using a fuel siphon pump (it is necessary for this operation)
Access the carburetor (part 14) located under the air filter cover
Open the carburetor drain screw (part 14) with a 10 mm wrench, placing a collection pan underneath to catch residual fuel
Let the fuel drain completely from the carburetor
Close the screw once the carburetor is emptied

Important: For a thorough cleaning of the carburetor or in case of persistent operational issues (difficult starting, engine stalling), it is highly recommended to entrust this operation to an authorized specialized workshop, as it is a complex intervention that requires disassembly and complete cleaning of the fuel system.

Question 7

What is the replacement blade for the PARKSIDE PBRM 39 C2 lawn mower and how do I replace it?

Accepted Answer

The reference of the blade for your PARKSIDE PBRM 39 C2 lawn mower is n° 7911200630. You can order it from Parkside spare parts dealers.

Replacement Steps

First, empty the fuel tank
Hold the blade with one hand
Unscrew the fixing screw (n° 20) counterclockwise
Remove the washer and install the new blade in reverse order
Tighten the screw to a torque of 45 Nm

Important: Sharpening and balancing of the blade must be done at an authorized Parkside service center to ensure proper balance and avoid vibrations. Never attempt to straighten a bent blade - it must be replaced.

Question 8

Is the PARKSIDE PBRM 39 C2 lawn mower self-propelled?

Accepted Answer

No, the PARKSIDE PBRM 39 C2 is not a self-propelled lawn mower. It is a manual mower that you must push yourself.

Equipped with a 4-stroke 131 cm³ gasoline engine (2.4 kW), the engine drives only the cutting blade (width 39 cm). The wheels are not motorized - it is the operator who provides the propulsion force by pushing on the handle.

This mower therefore requires constant physical effort to move forward. Depending on the terrain conditions and the grass to be cut, you will need to adjust your pushing force. It is suitable for flat or slightly sloped surfaces of small to medium size.

Question 9

How do I replace the power cord if it is damaged?

Accepted Answer

No, you should not replace the power cord of the PARKSIDE PNTS 1300 C3 vacuum cleaner yourself.

According to the device manual, if the power cord (4 m long) is damaged or broken, it must be replaced exclusively by the manufacturer, an authorized service center, or a qualified person. This applies to all class II devices like the PNTS 1300 C3.

Why shouldn't you do it yourself?

Risk of electric shock in case of improper connection
Non-compliance with the electrical safety standards required for this type of device
Potential loss of the product's 3-year warranty

What you should do:

Immediately stop using the vacuum cleaner
Contact PARKSIDE/Grizzly support
France Service: 0800 919270
Or visit www.grizzly-service.eu to request a repair

A professional repair ensures that the device remains compliant with standards and safe to use.

Question 10

What is the Ian code of the PARKSIDE PRM 1800 A2?

Accepted Answer

The Ian code of the PARKSIDE PRM 1800 A2 is: 373339_2104

This code is the unique identifier of the product and can be used to find spare parts, check warranty information, or any additional documentation from the manufacturer.

User manual PARKSIDE : user manuals and guides in PDF

Models PARKSIDE most viewed

Browse manuals PARKSIDE by appliance type

Recent questions about devices PARKSIDE