PKA 20Li B2 - Air compressor PARKSIDE - Free user manual and instructions

USER MANUAL PKA 20Li B2 PARKSIDE

20V CORDLESS COMPRESSOR AND AIR PUMP / 20-VOLT-AKKU-KOMPRESSOR UND -LUFTPUMPE COMPRESSEUR 20 V ET POMPE À AIR SANS FIL PKA 20-Li B2

GB IE

20V CORDLESS COMPRESSOR AND AIR PUMP

Translation of the original instructions

FR BE

COMPRESSEUR 20 V ET POMPE A AIR SANS FIL

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

DE AT CH

GB/IE Translation of the original instructions Page 1

Intended use 2
Features 2
Package contents 3
Technical specifications 3

General power tool safety warnings 4

1.Work area safety 4
2. Electrical safety
3. Personal safety 5
4. Power tool use and care 5
5. Battery tool use and care 6
6. Service 6

Appliance-specific safety instructions 6
Extended safety guidelines 7
Safety guidelines for battery chargers and blowers. 7

Before use 8

Charging the battery pack (see fig. A) 8
Attaching/disconnecting the battery pack to/from the appliance. 8
Checking the battery charge level 8

Operation 8

Switching on and off 9

Display 9

Setting the pressure 9

Use 9

Inflation withblowerhose 9
Deflation with compressed air hose. 10
Adapers 10
Inflation 10
Adapers 10

Maintenance, storage and cleaning 11

Disposal 11
Kompernass Handels GmbH warranty 12
Service 13
Importer 13
Original declaration of conformity 14
Ordering a replacement battery 15
Telephone ordering 15

20V CORDLESS COMPRESSOR AND AIR PUMP PKA 20-Li B2

Introduction

Congratulations on the purchase of your new appliance. You have chosen a high-quality product. The operating instructions are part of this product. They contain important information about safety, usage and disposal. Before using the product, please familiarise yourself with all operating and safety instructions. Use the product only as described and for the range of applications specified. Please also pass these operating instructions on to any future owner.

Intended use

The appliance is suitable for inflating bicycle tyres and inflatable toys, sports and beach articles using the adapters supplied. The appliance is not suitable for the operation of pneumatic tools. It is also suitable for measuring the current pressure in an inflated item. The pressure display is not calibrated. The compressor is not suitable for inflating car tyres.

The appliance is not intended for commercial use. Any other usage or modification of the appliance is deemed to be improper and carries a significant risk of accidents. The manufacturer accepts no responsibility for damage attributable to misuse.

NOTE

• Store these operating instructions in the immediate vicinity of the compressor and make them available to all operators.

Features

Appliance handle
Release button for the battery pack
3 Battery pack
4"-" button
ON/OFF button (for the display)
6"++button
ON/OFF switch (2 steps fan switch)
7a ON/OFF switch (LED work light)
7b LED work light
8 Display
Storage compartment (for the compressed air hose)
10 Compressed air hose valve adapter
1 Compressed air hose
12 Foot
Blower hose
14 Adapter nozzle
15 Adapter nozzle
16 Connection for the blower hose
Air outlet on the appliance
Air inlet on the appliance
Storage compartment (for the blower hose)
20 Storage compartment (for the accessories)
2 Battery charge level button
2 Battery display LED
23 High-speed charger
24 Red charge control LED
25 Green charge control LED
26 Valve adapter (Dunlop valve)
27 Ball needle
28 Universal adapter

Package contents

1 20V cordless compressor and air pump
1 compressed air hose with valve adapter
1blower hose
1 valve adapter (Dunlop valve)
1 ball valve (ball needle)
1 plastic adapter (universal adapter for valves with an inner of approx. 8mm
1 set of operating instructions

Technical specifications

Rated voltage 20V (DC)

Max. pressure 10.3 bar (150 psi)

Max. Speed 3500 rpm

Operating mode Continuous operation at constant load

Air flow rate blower 380 l/min

Air flow rate compressor 21 l/min

Weight, without

battery pack approx. 1.425kg

Battery PAP 20 A1*

Type
Rated voltage	20 V	= (DC)
Capacity	2	Ah
Cells	5

High-speed battery charger PLG 20 A1*

INPUT

Rated voltage 230-240 V\~, 50 Hz (AC)

Rated power

consumption 65 W

Fuse (internal) 3.15 A

OUTPUT

Rated voltage 21.5V (DC)

Rated current 2.4 A

Charging time approx. 60 min

Protection class II (double insulation)

• BATTERY AND CHARGER ARE NOT INCLUDED

Risk of burns caused by hot surfaces!

Wear hearing protection!

For indoor use only!

Do not expose to rain!

Noise emission value

The measured values were determined in accordance with the European Directives 2000/14/EC and 2005/88/EC. The A-weighted noise level is typically as follows:

Sound pressure level

LITHIUt the operator station) ION L_pA = 70.1 dB (A)

Uncertainty K_PA = 3dB

According to 2000/14/EC and 2005/88/EC:

Sound power level measured L_WA = 83.3 dB (A)

Uncertainty K_WA = 3.05 dB

Sound power level guaranteed L_WA = 86 dB (A)

Sound power level L_WA data in dB.

NOTE

The vibration emission values and the noise emission values given in these instructions have been measured in accordance with a standardised test procedure and can be used for comparison of the power tool with another tool.
The specified total vibration values and the noise emission values can also be used to make a provisional load estimate.

WARNING!

Depending on the manner in which the power tool is being used, and in particular the kind of workpiece that is being worked, the vibration and noise emission values can deviate from the values given in these instructions during actual use of the power tool.
Try to keep the load as low as possible. Measures to reduce the vibration load are, e.g. wearing gloves and limiting the working time. Wherein all states of operation must be included (e.g. times when the power tool is switched off and times where the power tool is switched on but running without load).

General power tool safety warnings

WARNING!

Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Battery tool use and care

a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
e) Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130^ (265^) may cause explosion.
g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

CAUTION! RISK OF EXPLOSION! Never charge non-rechargeable batteries!

Protect the recharge- at, for example from to sunlight, fire, water a risk of explosion.

6. Service

a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Appliance-specific safety instructions

This appliance may not be used by children or people with reduced physical, sensory or mental capabilities or a lack of experience and knowledge. Do not allow children to use the appliance as a toy. Cleaning and user maintenance tasks may not be carried out by children unless they are supervised.
Protect the unit from rain and moisture.
Avoid using the compressor at temperatures below 5^
Never leave the compressor unsupervised while it is in use.
Caution! Operate the compressor for short periods only. The appliance may overheat if operated for longer than 10 minutes. Switch the appliance off immediately and allow it to cool down for at least 10min

■ Risk of injury! Do not pump any objects up to more than the intended pressure. They could burst and cause injuries and/or material damage.

• Do not exceed the permissible output range of the compressor. Do not use the compressor to pump up lorry, tractor or other large tires.

Do not work on materials that are or could be potentially flammable or explosive.

Never use the appliance for purposes other than those for which it was designed.

The appliance must always be kept clean, dry and free from oil or grease.

Never use petrol or other flammable liquids to clean the appliance! Vapours remaining in the appliance can be ignited by sparks and cause the appliance to explode.

Remain alert at all times! Do not use the appliance if you are distracted or feeling unwell.

• Avoid heavy loads on the pipe system by using flexible hose connections to avoid kinks.

Avoid heavy loads on the piping system by using flexible hose connections to avoid kinks.

It is recommended that feed hoses are fitted with a safety cable, e.g. B. should be equipped with a wire rope.

Extended safety guidelines

Do not use a damaged or modified battery. Damaged or modified batteries may behave unexpectedly and cause fires, explosions or pose a risk of injury.

Do not expose a battery to fire or excessively high temperatures. Fire or temperatures in excess of 130^ (265^) can cause an explosion.

Follow all instructions regarding charging and never charge the battery or the cordless tool outside the temperature range given in the operating instructions. Incorrect charging or charging outside of the permissible temperature range can destroy the battery and increase the risk of fire.

Safety guidelines for battery chargers and blowers

This appliance may be used by children aged 8 years and above and by persons with limited physical, sensory or mental capabilities or lack of experience and knowledge, provided that they are under supervision or have been told how to use the appliance safely and are aware of the potential risks. Do not allow children to use the appliance as a toy. Cleaning and user maintenance tasks may not be carried out by children unless they are supervised.

The charger is suitable for indoor use only.

WARNING!

To avoid potential risks, damaged mains cables should be replaced by the manufacturer, their customer service department or a similarly qualified person.

ATTENTION!

This charger can only charge the following batteries: PAP 20 A1/PAP 20 A2/ PAP 20 A3/PAP 20 B1/PAP 20 B3/ PAPS 204 A1/PAPS 208 A1.

A current list of battery compatibility can be found at www.Lidl.de/Akku.

Before use

Charging the battery pack (see fig. A)

CAUTION!

Always unplug the charger before you remove the battery pack 3 from or connect it to the charger.

NOTE

The recommended ambient temperature range for using tools and batteries is between -5^ and 50^ .
- Never charge the battery pack at an ambient temperature of below 10^ or above 40^ . If a lithium-ion battery is going to be stored for an extended period, the charge level should be checked regularly. The optimum charge level is between 50% and 80% . The storage climate should be cool and dry and the ambient temperature should be between 0^ and 50^ .

Connect the battery pack 3 to the high-speed battery charger 2 see fig.A).
Insert the mains plug into the mains socket. The control LED 24 lights up red.
The green control LED25 indicates that the charging process is complete and the battery pack 3 ready for use.

ATTENTION!

If the red control LED24 flashes, this means that the battery pack 3 as overheated and cannot be charged.
If the red and green control LED24 25 both flash, this means that the battery pack 3 defective.
Switch off the charger for at least 15 minutes between successive charging sessions. Also disconnect the power plug from the mains power socket.

Attaching/disconnecting the battery pack to/from the appliance

Inserting the battery pack

Allow the battery pack to click into place in the appliance.

Removing the battery pack

Press the release butto 2 and remove the battery pack 3.

Checking the battery charge level

Press the battery charge level button 2 to check the status of the battery (see also figure A on the fold-out page).

The status/remaining charge will be shown on the battery display LED 2 as follows:

RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge

RED = low charge - charge the battery

Operation

NOTE

The appliance vibrates during operation. Place it on a solid surface during operation. There are four feet 12 on the bottom of the appliance for this purpose.

ATTENTION!

This appliance is not designed for continuous operation. The appliance may be used for a maximum of 10 minutes continuous operation. If the appliance overheats, remove the battery pack 3. Allow the appliance to cool down completely and then try using it again.

Remove the required accessories from the storage compartment 20.

Switching on and off

Switching on the appliance (air pump)

Set the ON/OFF switch to the position

Switching on the appliance (compressor)

Set the ON/OFF switch to the position

The appliance starts as soon as you switch on the display (see section "Display").

Switching on the LED work light

Set the ON/OFF switch to position "l". The LED work light lights up.

NOTE

The compressor will not work if the display is switched off.

Switching off the appliance

Set the ON/OFF switch to the position

Switching off the LED work light

Set the ON/OFF switch to position "O".

Display

Press the ON/OFF button to switch on the display

After two seconds, the current pressure of the connected item is shown.

NOTE

If the compressed air hose is not connected to a suitable item, the display indicator shows "0".

You can switch between "bar", "psi" and "kpa" on the display by pressing the ON/OFF button

NOTE

The display (and also the compressor) switches off after around three minutes of inactivity.

The compressor will not work if the display is switched off.

NOTE

The compressor switches off automatically when the preset pressure has been reached.

Press and hold the ON/OFF butto ⑤ for 5 seconds to turn off the display 8.

Setting the pressure

Press the "+" button or the "-" button set the desired pressure.

TIP

When you press and hold the "+" butto 6 or the "-" button 4 or a little longer, the pressure setting changes quickly.

Use

Inflation with blower hose

Remove the valve cap of the item you want to inflate.

Remove the blower host from the storage compartment 19

Fit the connection of the blower host onto the air outlet 16crew it in tight by turning it clockwise.

Fit the appropriate adapter or 1nto the blower hose 13

Push the adapter or into the valve of the item.

Switch the appliance on by moving the ON/OFF switch ⑦ to the position.

Once the desired level of inflation has been reached, switch off the appliance by moving the ON/OFF switch to the position

Now remove the adapter or 15

Replace the valve cap on the item that you have inflated.

Deflation with compressed air hose

Remove the valve cap of the item you want to deflate.
Remove the blower hose from the storage compartment 19
Push the connection of the blower hose onto the air inlet 18
Fit the appropriate adaptet or into the blower hose 13
Push the adapteto the valve of the item.
Switch the appliance on by moving the ON/OFF switch 7 to the position
Once the item is fully deflated, switch off the appliance by moving the ON/OFF switch to the position.
Now remove the adapter or 15

Adapters

Adapter 14

For standard valves with an internal diameter of 8mm

Adapter 15

For inflatable items with a screw valve. Deflation is only possible with an unscrewed valve and with this adapter.

Inflation

Switch on the display (see section "Display").
Select the desired pressure (see section "Setting the pressure").
Remove the compressed air host from the storage compartment
Plug in one of the supplied adapter36,27r 28 into the compressed air hose valve adapter10 (see illustration).

Connect the adapter, 25r t3he object you want to inflate.
Set the ON/OFF switch to the position The appliance starts.
The compressor switches off automatically when you reach the preset pressure.
Pull the adapte26, 2r of the now inflated item.

Adapters

Adapter 26

The Dunlop valve can be used for inflating bicycle tyres.

Adapter

The ball needle can be used to inflate various balls.

Adapter 20

The universal adapter can be used to inflate air mattresses or similar.

Maintenance, storage and cleaning

WARNING! RISK OF ELECTROCUTION! Before cleaning, disconnect the charger from the mains socket.

NOTE

Before carrying out any work on the appliances, ensure that the battery pack 3 has been removed. This prevents the appliance from being switched on unintentionally.
The cordless appliances are maintenance-free.
The appliances must always be clean, dry and free from oil or grease.
Never allow liquids to get into the appliances.
Use a soft cloth to clean the housing. Never use petrol, solvents or cleansers which can damage plastic.
Always ensure the appliances and attachments are clean, free of dust and dry before storing.
If you do not intend to use the appliances for a longer time, remove the batteries and store them in a clean, dry place away from direct sunlight.
If a lithium-ion battery is going to be stored for an extended period, the charge level should be checked regularly. The optimum charge level is between 50% and 80% . The optimum storage environment is cool and dry.
- Never try to repair damaged batteries. Batteries should only be maintained by the manufacturer or an approved customer service centre.

NOTE

• Replacement parts that are not listed (such as batteries, chargers) can be ordered via our Service Hotline.

Disposal

The packaging is made from environmentally friendly material and can be disposed of at your local recycling centres.

Do not dispose of power tools in the normal domestic waste!

European Directive 2012/19/EU requires that worn-out power tools

be collected separately and recycled in an environmentally compatible manner.

Lion

Do not dispose of batteries in your normal household waste!

Defective or worn-out rechargeable batteries must be recycled according to Directive 2006/66/EC. Take the

battery pack and/or the appliance to a nearby collection facility.

Please contact your local authority or town council for information about disposal options for used power tools/battery packs.

Dispose of the packaging in an environmentally friendly manner.

Note the labelling on the packaging and separate the packaging material

components for disposal if necessary. The packaging material is labelled with abbreviations (a) and numbers (b) with the following meanings: 1-7: plastics, 20-22: paper and cardboard, 80-98: composites.

Your local community or municipal authorities can provide information on how to dispose of the worn-out product.

The product is recyclable, subject to extended producer responsibility and is collected separately.

KompernassHandelsGmbH warranty

Dear Customer,

This appliance has a 3-year warranty valid from the date of purchase. If this product has any faults, you, the buyer, have certain statutory rights. Your statutory rights are not restricted in any way by the warranty described below.

Warranty conditions

The warranty period starts on the date of purchase. Please keep your receipt in a safe place. This will be required as proof of purchase.

If any material or manufacturing fault occurs within three years of the date of purchase of the product, we will either repair or replace the product for you or refund the purchase price (at our discretion).

This warranty service requires that you present the defective appliance and the proof of purchase (receipt) within the three-year warranty period, along with a brief written description of the fault and of when it occurred.

If the defect is covered by the warranty, your product will either be repaired or replaced by us. The repair or replacement of a product does not signify the beginning of a new warranty period.

X 12 V and X 20 V Team Series battery packs come with a 3-year warranty valid from the date of purchase.

Warranty period and statutory claims for defects

The warranty period is not prolonged by repairs effected under the warranty. This also applies to replaced and repaired components. Any damage and defects present at the time of purchase must be reported immediately after unpacking. Repairs carried out after expiry of the warranty period shall be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accordance with strict quality guidelines and inspected meticulously prior to delivery.

The warranty covers material faults or production faults. The warranty does not extend to product parts subject to normal wear and tear or to fragile parts which could be considered as consumable parts such as switches or parts made of glass.

The warranty does not apply if the product has been damaged, improperly used or improperly maintained. The directions in the operating instructions for the product regarding proper use of the product are to be strictly followed. Uses and actions that are discouraged in the operating instructions or which are warned against must be avoided.

This product is intended solely for private use and not for commercial purposes. The warranty shall be deemed void in cases of misuse or improper handling, use of force and modifications / repairs which have not been carried out by one of our authorised Service centres.

The warranty period does not apply to

Normal reduction of the battery capacity over time
Commercial use of the product
Damage to or alteration of the product by the customer
Non-compliance with safety and maintenance instructions, operating errors
Damage caused by natural hazards

Warranty claim procedure

To ensure quick processing of your case, please observe the following instructions:

Please have the till receipt and the item number (IAN) 380759_2110 available as proof of purchase.
You will find the item number on the type plate on the product, an engraving on the product, on the front page of the operating instructions (below left) or on the sticker on the rear or bottom of the product.
If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.
You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.

You can download these instructions along with many other manuals, product videos and installation software at www.lidl-service.com.

This QR code will take you directly to the Lidl service page (www.lidl-service.com) where you can open your operating instructions by entering the item number (IAN) 380759_2110.

WARNING!

Have your appliances repaired by the Service Centre or a qualified electrician and only using genuine replacement parts. This will ensure that the safety of the appliance is maintained.
Always ensure that the power plug and power cord are replaced only by the manufacturer of the appliance or the company customer service. This will ensure that the safety of the appliance is maintained.

Service

GB Service Great Britain Tel.:[phone] E-Mail: [e-mail]
IE Servicelreland Tel.:[phone] E-Mail:[e-mail] IAN380759_2110

Importer

Please note that the following address is not the service address. Please use the service address provided in the operating instructions.

KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com

Original declaration of conformity

We, KOMPERNASS HANDELS GMBH, documents officer: Mr. Semi Uguzlu, BURGSTR. 21, 44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards, normative documents and EC directives:

Machinery Directive (2006/42/EC)

EC Low Voltage Directive (2014/35/EU, only charger)

Noise emission directive (2000/14/EC), (2005/88/EC)

Sound power level LWA:Guaranteed:86 dB (A)

EMC (Electromagnetic Compatibility) (2014/30/EU)

RoHS Directive (2011/65/EU)*

• The manufacturer bears the full responsibility for compliance with this conformity declaration. The subject of the declaration described above meets the requirements of Directive 2011/65/EU of the European Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic appliances.

Related harmonised standards

EN 1012-1:2010

EN 62841-1:2015

EK9-BE-103:2020

EN IEC 55014-1:2021

EN IEC 55014-2:2021

EN IEC 63000:2018

Type designation of machine: 20V Cordless Compressor and Air Pump PKA 20-Li B2

Year of manufacture: 02-2022

Serial number: IAN 380759_2110

Bochum, 01/02/2022

Semi Uguzlu

• Quality Manager -

We reserve the right to make technical changes in the context of further product development.

Ordering a replacement battery

If you want to order a replacement battery for your tool, you can do so easily via the Internet on www.kompernass.com or by telephone.

Due to limited stocks, this item may sell out in a relatively short time.

NOTE

• Online ordering of replacement parts is not possible in all countries. If this is the case, please contact the Service hotline.

Telephone ordering

GB Service Great Britain Tel.: [phone]
IE ServiceIrelandTel.: 1800 101010

To ensure fast processing of your order, have the article number of your appliance to hand (IAN 380759_2110) in case of questions. The article number can be found on the type plate or the title page of these instructions.

Inhaltsverzeichnis

Einleitung 18

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

(Courant alternative)

Puisssance nominale

absorbee

65W

Fusible (interne)

3,15A

SORTIE/output

Tension nominale 21,5 V (courant continu)

Chere cliente, cher client,

Chere cliente, cher client,

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

ALLEMAGNE

www.kompernass.com

Directive relative aux machines (2006/42/CE)

Directive RoHS (2011/65/EU)*

• Responsible qualite -

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

NEMECKO

www.kompernass.com

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

NIEMCY

www.kompernass.com

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

NEMECKO

www.kompernass.com

Originalne vyhlasenie o zhode

My, spolocnost' KOMPERNASS HANDELS GMBH, osoba zodpovedna za dokumentaciu: pán Semi Uguzlu, BURGSTR. 21, 44867 BOCHUM, DEUTSCHLAND/NEMECKO vyhlasujeme, ze tento vyrobok je v sulade s nasledujucimi normami, normativnymi dokumentmi a smernicami ES:

Smernica o strojovych zariadeniach (2006/42/EC)

Smernica ES o nizkom napati (2014/35/EU, iba nabijačka)

Sernica emisia hluku (2000/14/EC), (2005/88/EC)

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

ALEMANIA

www.kompernass.com

Bestilling of reservebatteri 144

Telefonisk bestilling 144

20 V BATTERIDREVET KOMPRESSOR OG LUFTPUMPE PKA 20-Li B2

Indledning

Luffflow compressor 21 l/min

Vaegt,edenbatteri ca.1,425kg

Batteri PAP 20 A1*

Type

LITHIUM-ION

pu

续表

tsia

101

men)

L_PA = 70,1 dB( A)

Usikkerhed

K_PA = 3 dB

Maerkespaending

-20 (jævn'srøm)

Kapacitet 2

Ah

Celler 5

Batteridrevet hurtigoplader PLG 20 A1*

INDGANG

Mærkespaending 230-240 V\~,50 Hz (vekselsstrom)

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

TYSKLAND

www.kompernass.com

Original overensstemmelseserklaering

Vi, KOMPERNASS HANDELS GMBH, dokumentansvarlig: Semi Uguzlu, BURGSTR. 21, 44867 BOCHUM, TYSKLAND, erklær hermed, at dette produktstemmer overens med følgende standarder, standardiseringsdokumenter og EU-direktiver:

Maskindirektivet (2006/42/EC)

RoHS-directivet (2011/65/EU)*

Bestilling of reservebatteri

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANIA

www.kompernass.com

Negotovost K_WA = 3,05 dB

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

NEMCIJA

www.kompernass.com

OPOZORILO!

Svoje naprave daje v popravilo samo servisni službi ali strokovnjaku za elektrotehniko, ki nj uporablja le originalne nadomestne dele. S tem zagotovite, da se ochrani varnost naprave.
Zamenjavo vtica ali elektricnega kabla zmeraj prepustite proizvajalu naprave ali njegovi servisni sluzbi. S tem zagotovite, da se ohrani varnost naprave.

Pooblasceni serviser

SI ServisSlovenija

Tel.: [phone]

E-Mail: [e-mail]

IAN380759_2110

Garancijski list

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompermass.com

Last Information Update · Stand der Informationen · Version des informations · Stand van de informatie · Stav informaci · Stan informacji

Stav informacié - Estado de las informaciones - Tilstand af information - Versione delle informazioni - Informacionk allasa - Stanje informacij:

02/2022·Ident.-No.:PKA20-LiB2-022022-1