KW1200E - Milling machine BLACK & DECKER - Free user manual and instructions

Frequently Asked Questions - KW1200E BLACK & DECKER

USER MANUAL KW1200E BLACK & DECKER

ENGLISH (Original instructions)

Intended use Your BLACK+DECKER KW1200E, KW1200EKA router has been designed for routing wood and wood products. This tool is intended for consumer use only. Safety instructions Warning! When using mains-powered and battery powered appliances, basic safety precautions, including the following, should always be followed to reduce the risk of re, electric shock, personal injury and material damage. General power tool safety warnings Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, re and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents. b. Do not operate power tools in explosive atmospheres, suchasinthepresenceofammableliquids,gases or dust. Power tools create sparks which may ignite the dust or fumes. c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will reduce risk of electric shock. b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a powertoolwhileyouaretiredorundertheinuence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b. Usepersonalprotectiveequipment.Alwaysweareye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your nger on the switch or energising power tools that have the switch on invites accidents. d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.8 ENGLISH (Original instructions) d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g. Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

a. Haveyourpowertoolservicedbyaqualiedrepair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Additional power tool safety warnings Warning! Additional safety warnings for routers u Hold the power tool by the insulated gripping surfaces, because the cutter may contact its own cord. Cutting a "live" wire may make exposed metal parts of the power tool "live" and shock the operator. u Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. Warning! Contact with, or inhalation of dusts arising from routing applications may endanger the health of the operator and possible bystanders. Wear a dust mask specically designed for protection against dust and fumes and ensure that persons within or entering the work area are also protected. u Thoroughly remove all dust after routing. u Only use router bits with a shank diameter equal to the size of the collet installed in the tool. u Only use router bits suitable for the no-load speed of the tool. u Never use router bits with a diameter exceeding the maximum diameter specied in the technical data section. u Do not use the tool in an inverted position. u Do not attempt to use the tool in a stationary mode. u If the supply cord is damaged, it must be replaced by the manufacturer or an authorised BLACK+DECKER ServiceCentre in order to avoid hazard. u Take special care when routing where the paint is possibly lead based or when routing some woods which may produce toxic dust: u Do not let children or pregnant women enter the work area. u Do not eat, drink or smoke in the work area. u Dispose of dust particles and any other debris safely. u The intended use is described in this instruction manual. The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury and/or damage to property. Safety of others u Never allow children, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge or people unfamiliar with these instructions to use the machine, local regulations may restrict the age of the operator. u Never operate the machine while people, especially children, or pets are nearby. Residual risks Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc. Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include: u Injuries caused by touching any rotating/moving parts. u Injuries caused when changing any parts, blades or accessories. u Injuries caused by prolonged use of a tool. When using any tool for prolonged periods ensure you take regular breaks. u Impairment of hearing. u Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF.) Vibration The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN50636 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. Warning! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used.9 ENGLISH (Original instructions) The vibration level may increase above the level stated. When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time. Labels on tool The following pictograms, along with the date code, are shown on the tool: Warning! To reduce the risk of injury, the user must read the instruction manual. Electrical safety This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. u If the supply cord is damaged, it must be replaced by the manufacturer or an authorised BLACK+DECKER Service Centre in order to avoid a hazard Features This tool contains all or some of the following features:

10. Depth of cut scale

11. Dust extraction adaptor

Assembly Warning! Before assembly, make sure that the tool is switched off and unplugged. Fittingarouterbit(g.A) u Remove the chip deector (8). u Keep the spindle lock button (5) depressed and rotate the spindle until the spindle lock fully engages. u Loosen the collet nut (12) using the spanner provided. u Insert the shank of the router bit (13) into the collet (6). Make sure that the shank protrudes at least 3 mm from the collet as shown. u Keep the spindle lock button (5) depressed and tighten the collet nut (12) using the spanner provided. Fittingtheedgeguide(g.B) The edge guide helps to guide the tool parallel to an edge. u Fit the bars (14) to the edge guide (15) using the two screws (16) provided. u Insert the bars (14) into the router base as shown. u Set the edge guide to the required distance. u Tighten the xing screws (17). Fittingthedustextractionadaptor(g.C) The dust extraction adaptor allows you to connect a vacuum cleaner to the tool. u Connect the hose (18) of the vacuum cleaner to the adaptor (11). Fittingthetemplateguide(g.D) u Fit the template guide (19) to the base of the router, with the ange to the bottom (workpiece) side. u Insert the two long screws (20) from the bottom side through the template guide and the holes in the base. u Place a nut onto each of the screws and securely tighten the nuts. Fittingthedistancepiece(Optional)(g.E) u Fit the distance piece (21) to the base of the router using the screws provided. Fittingthecentringpin(g.F) u Fit the centring pin (22) to the workpiece side of the bars, then tighten it with the steel knob (23) provided . Fittingthecopyfollower(Optional)(g.G) u Fit the edge guide to the router as shown in g. B. u Fit the 'L' bar(24) to the upper side of the edge guide using the two screws and nuts provided. u Adjust the rotating attachment (25) on the 'L' bar with the wing knob (26). Use Warning! Let the tool work at its own pace. Do not overload. u Carefully guide the cable in order to avoid accidentally cutting it. Adjustingthedepthofcut(g.H,I&J) The depth of cut is the distance X between the depth stop bar (9) and the depth stop (7). The depth of cut can be set in two different ways as described below. Adjustingthedepthofcutusingthescale(g.I) u Fit the router bit as described above.10 ENGLISH (Original instructions) u Loosen the locking screw (28). u Pull the plunge lock lever (4) up. u Plunge the router down until the router bit touches the workpiece. u Push the plunge lock lever (4) down. u Move the pointer (29) in the zero position on the scale (10). u Add the desired depth of cut to the starting position. u Move the depth stop bar (9) to the calculated position on the scale. u Tighten the locking screw (28). u Fine adjust using the adjusting knob (30). u Pull the plunge lock lever (4) up and let the router return to its original position. u After switching the router on, plunge it down and make the desired cut. Adjusting the depth of cut using a piece of wood (g.J) u Fit the router bit and plunge the router down as described above. u Pull the depth stop bar (9) up. u Place a piece of wood with a thickness equal to the desired depth of cut between the depth stop (7) and the depth stop bar (9). u Tighten the locking screw (28). u Fine adjust using the adjusting knob (30). u Remove the piece of wood. u Pull the plunge lock lever (4) up and let the router return to its original position. u After switching the router on, plunge it down and make the desired cut. Adjustingtherevolverdepthstop(g.K) After turning the revolver depth stop to the desired setting, you can ne-adjust the depth stop to be used. If you want to make several cuts with a different depth of cut, adjust each of the depth stops. Setting the speed u Set the speed control knob (3) to the required speed. Use a high speed for small diameter router bits. Use a low speed for large diameter router bits. Usingabattenasaguide(g.L) When it is not possible to use the edge guide, for example when routing grooves in the back panel of a bookcase to support shelves, proceed as follows: u Select a piece of wood with a straight edge to use as a batten. u Place the batten onto the workpiece. u Move the batten until it is in the correct position to guide the tool. u Securely clamp the batten to the workpiece. Usingthetemplateguide(g.D) The template guide can be used to make a cutout shape from a template, for instance a letter. u Secure the template over the workpiece with double-sided tape or ‘G' clamps. u The router bit must extend below the ange of the template guide, to cut the workpiece in the shape of the template. Usingthedistancepiece(Optional)(g.E) The distance piece can be used for trimming wooden or laminate vertical projections. Usingthecentringpin(g.F) The centring pin can be used to cut out circular patterns. u Drill a hole for the point of the centring pin in the centre of the circle to be cut. u Place the router on the workpiece with the point of the centring pin in the drilled hole. u Adjust the radius of the circle with the bars. u The router can now be moved over the workpiece to cut out the circle. Usingthecopyfollower(Optional)(g.G) The copy follower helps to maintain an equal cutting distance along the edge of irregularly shaped workpieces. u Place the router on the workpiece at the desired distance from the edge to be copied. u Adjust the bars of the edge guide until the wheel is in contact with the workpiece. Switching on and off Switching on u Keep the lock-off button (2) depressed and press the on/ off switch (1). u Release the lock-off button. Switching off u Release the on/off switch. Warning! Always operate the tool with both hands. Hints for optimum use u When working on outside edges, move the tool counterclockwise (g. M). When working on inside edges, move the tool clockwise. u Use HSS router bits for softwood. u Use TCT router bits for hardwood.11 ENGLISH (Original instructions) u You can use the tool without a guide (g. N). This is useful for signwriting and creative work. Only make shallow cuts. u Refer to the table below for common types of router bits. Routerbits(Optional)(g.O) Description Application Straight bit (1) Grooves and rebates. Trimming bit (2) Trimming laminates or hardwood; accurate proling using a template. Rebating bit (3) Rebates on straight or curved workpieces. V-grooving bit (4) Grooves, engraving and edge bevelling. Core box bit (5) Fluting, engraving and decorative edge moulding. Cove bit (6) Decorative edge moulding Ogee moulding bit (7) Decorative edge moulding Rounding over bit (8) Rounding over edges Dovetail bit (9) Dovetail joints Chamfer bit (10) Chamfer edges Maintenance Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance, switch off and unplug the tool. u Regularly clean the ventilation slots in your tool using a soft brush or dry cloth. u Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner. Mainsplugreplacement(U.K.&Irelandonly) If a new mains plug needs to be tted: u Safely dispose of the old plug. u Connect the brown lead to the live terminal in the new plug. u Connect the blue lead to the neutral terminal. u Connect the green/yellow lead to the earth terminal. Warning! Follow the tting instructions supplied with good quality plugs. Recommended fuse: 13 A. Protecting the environment Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste. Products and batteries contain materials that can be recov- ered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com Technical Data KW1200E- KW1200EKA Input voltage V

EC declaration of conformity MACHINERY DIRECTIVE KW1200E, KW1200EKA Router Black & Decker declares that these products described under "technical data" are in compliance with: 2006/42/EC, EN 60745-1:2009 + A11:2010, EN 60745-2-17:2010 These products also comply with Directive 2014/30/EU and 2011/65/EU. For more information, please contact Black & Decker at the following address or refer to the back of the manual.(Übersetzung der ursprünglichen Anweisungen) DEUTSCH