Q: How to assemble the parts of the hood in recirculation mode?

Recirculation mode - Key elements to know: The ELECTROLUX HOTTELFT416X hood can operate in recirculation mode (also known as filtering mode). In this mode, the air is filtered and then expelled back into the room. Essential component For recirculation mode, an active charcoal filter is essential . This filter: Cannot be cleaned or washed Must be replaced every 4 months of use (more often in case of intensive use) Should be ordered from Electrolux (original spare parts) Meanwhile, grease filters should be regularly cleaned (approximately every 2 months). About assembly Unfortunately, the manual for your hood does not contain detailed step-by-step instructions for assembling the parts in recirculation mode. For precise assembly details (filter orientation, fixings, etc.), we recommend consulting the specific installation manual or contacting Electrolux directly, as this configuration depends on the exact version of your model. Generally, for this type of hood, recirculation mode involves installing the charcoal filter in its designated housing, securing the grease filters if necessary, and checking the tightness of the circuit to prevent air leaks.

Q: Can I use a bulb with a power lower than 20 W in this hood?

No, you must not use a bulb with a power lower than 20 W. The ELECTROLUX EFC60640X hood is designed exclusively to operate with a 20 W halogen bulb . Why not use a lower power? Insufficient lighting: A bulb with lower power will provide significantly less light for the cooking area, making it difficult to clearly see your dishes in preparation. Fixture incompatibility: The socket and power supply of the hood are calibrated for 20 W. A lower power may lead to unstable operation or damage the lighting circuit. Warranty risk: Using a non-recommended bulb may void your manufacturer's warranty. Tip: Always replace the bulb with an identical 20 W halogen bulb to the original. If your bulb frequently blows, it may indicate an electrical problem that you should have checked rather than reducing the power.

Q: How do I open and close the lid of the Electrolux DVE5671HG hood?

On the Electrolux DVE5671HG , the lid opens by simply pulling it. Here are the precise steps: Opening the lid Pull on the lid to open it. This is the only action needed to access the inside of the hood. Removing and reinstalling the filters Once the lid is open, you can access the filters: Press the lever of the filter clamp located under the hood Gently tilt the front of the filter downwards Pull the filter towards you to remove it If necessary, use pliers to manipulate the pivots on the opposite side Closing and reassembling To close, simply follow the first two steps in reverse order after cleaning or replacing the filters. The lid will close by pushing it until you hear the locking click.

Question 1

How to assemble the parts of the hood in recirculation mode?

Accepted Answer

Recirculation mode - Key elements to know:

The ELECTROLUX HOTTELFT416X hood can operate in recirculation mode (also known as filtering mode). In this mode, the air is filtered and then expelled back into the room.

Essential component

For recirculation mode, an active charcoal filter is essential. This filter:

Cannot be cleaned or washed
Must be replaced every 4 months of use (more often in case of intensive use)
Should be ordered from Electrolux (original spare parts)

Meanwhile, grease filters should be regularly cleaned (approximately every 2 months).

About assembly

Unfortunately, the manual for your hood does not contain detailed step-by-step instructions for assembling the parts in recirculation mode. For precise assembly details (filter orientation, fixings, etc.), we recommend consulting the specific installation manual or contacting Electrolux directly, as this configuration depends on the exact version of your model.

Generally, for this type of hood, recirculation mode involves installing the charcoal filter in its designated housing, securing the grease filters if necessary, and checking the tightness of the circuit to prevent air leaks.

Question 2

Can I use a bulb with a power lower than 20 W in this hood?

Accepted Answer

No, you must not use a bulb with a power lower than 20 W. The ELECTROLUX EFC60640X hood is designed exclusively to operate with a 20 W halogen bulb.

Why not use a lower power?

Insufficient lighting: A bulb with lower power will provide significantly less light for the cooking area, making it difficult to clearly see your dishes in preparation.
Fixture incompatibility: The socket and power supply of the hood are calibrated for 20 W. A lower power may lead to unstable operation or damage the lighting circuit.
Warranty risk: Using a non-recommended bulb may void your manufacturer's warranty.

Tip: Always replace the bulb with an identical 20 W halogen bulb to the original. If your bulb frequently blows, it may indicate an electrical problem that you should have checked rather than reducing the power.

Question 3

How to unclip the bulb locking device?

Accepted Answer

To remove the metal locking device from the halogen bulb (20 W) of your ELECTROLUX EFC60640X:

Hold the glass with one hand to support it
Apply pressure under the tip of the locking device
The device will unclip and can be removed
Once the new bulb is installed, reinstall the device by clicking it back in until you hear a click

This operation is detailed on pages 69-80 of the manual with 14 illustrations to guide you.

Question 4

How to replace the halogen bulbs in the extractor hood?

Accepted Answer

To replace the 20 W halogen bulb in your ELECTROLUX EFC60640X:

Replacement Steps

Remove the locking device - Hold the glass with one hand and press under the tip of the metal locking device to remove it by snapping it off.
Extract the used bulb - Carefully remove the lamp from the socket.
Insert the new bulb - Insert a new halogen bulb, strictly identical (20 W). Ensure that both pins of the connector are correctly positioned in the socket.
Reinstall the locking device - Snap the metal locking device back in place until you hear a click, pressing from the top.

Important: Only use a 20 W halogen bulb identical to the original. Both connectors must be perfectly engaged for optimal operation and safety. The PDF of your manual contains 14 detailed illustrations for this operation (pages 69-80).

Question 5

How do I open and close the lid of the Electrolux DVE5671HG hood?

Accepted Answer

On the Electrolux DVE5671HG, the lid opens by simply pulling it. Here are the precise steps:

Opening the lid

Pull on the lid to open it. This is the only action needed to access the inside of the hood.

Removing and reinstalling the filters

Once the lid is open, you can access the filters:

Press the lever of the filter clamp located under the hood
Gently tilt the front of the filter downwards
Pull the filter towards you to remove it
If necessary, use pliers to manipulate the pivots on the opposite side

Closing and reassembling

To close, simply follow the first two steps in reverse order after cleaning or replacing the filters. The lid will close by pushing it until you hear the locking click.

Question 6

How to install the charcoal filter on this kitchen hood?

Accepted Answer

The charcoal filter of your Electrolux LFP616K hood is easy to install and allows the hood to operate in recirculation mode (air recirculation). Here’s how to proceed:

Installing the charcoal filter

First, clean the grease filter: The charcoal filter works best when the grease filter is not clogged. Start by cleaning or replacing the grease filter if necessary.
Insert the filter: Slide the charcoal filter into its designated slot behind the hood's front panel. Make sure it is securely in place.
Check the fit: The filter must be firmly installed before turning the ventilation back on.

Important points to remember

Not washable: Unlike the grease filter, the charcoal filter is not washable. It can only be replaced.

Regular replacement: Replace the charcoal filter at least every 4 months, depending on your usage frequency and cooking type. A saturated filter reduces the efficiency of air recirculation.

Note: The manual does not include detailed installation images for the charcoal filter. For additional instructions, please refer to the Electrolux support website.

Question 7

Is there an electrical diagram available for the Electrolux CE6010GR hood?

Accepted Answer

No, this manual does not include a complete electrical diagram. However, it provides the essential electrical specifications:

Power supply: 220-240 V with mandatory grounding
Required bipolar switch with a minimum contact opening of 3 mm
3 motor speeds (low, medium, high) controlled by mechanical switches

For a repair or modification of the electrical circuit, contact the authorized Electrolux after-sales service. The replacement of the power cord, in particular, must be carried out by an authorized professional for safety reasons.

If you need the complete original diagram, detailed technical sheets are available from the Electrolux technical service with the model number CE6010GR.

Question 8

How to wire and connect the Electrolux CE6010GR hood to electricity?

Accepted Answer

The Electrolux CE6010GR hood operates on an electrical supply of 220-240 V with mandatory grounding. This grounding must comply with current standards to ensure your safety: check that the domestic electrical installation has a properly connected ground before making the connection.

Installation of the bipolar switch: The connection to electricity must be made by interposing a bipolar switch with a contact opening of at least 3 mm. This switch allows for complete disconnection of the hood's power supply, ensuring total disconnection from the electrical network. Do not connect the hood directly to a power outlet.

Verification before installation: Before proceeding with the connection, check that the voltage of your electrical network (indicated on the rating plate affixed inside the hood) matches your domestic supply (220-240 V). This verification is crucial to avoid any malfunction or damage to the appliance.

Maintenance of the power cord: If the cord or power cable is damaged, it must be replaced exclusively by the manufacturer Electrolux or by an authorized after-sales service. Never attempt to repair a defective cable yourself, as this poses serious risks of electrocution. Professional repair ensures compliance and safety of the installation.

Commissioning: Once the bipolar switch is installed and the grounding verified, the hood is ready to be commissioned. The three motor speeds and lighting can then be controlled via the mechanical switches on the control panel. For more details on other installation elements (extraction ducting, mounting height), refer to the complete product manual.

Question 9

How do I change the activated charcoal filter in my hood?

Accepted Answer

The activated charcoal filter in your Electrolux EFP60460OX hood must be replaced regularly as it is not washable and not regenerable.

Filter Replacement

Recommended frequency: Replace the charcoal filter at most every four months. The saturation of the filter depends on the frequency of use and the regularity of cleaning the grease filter.

To obtain the original replacement filter suitable for your EFP60460OX model, visit www.electrolux.com/shop where you will find the appropriate accessories and original parts.

Replace the filter as soon as it is saturated or its absorption efficiency decreases, to maintain good odor absorption.

Question 10

How do I change the activated charcoal filter of my hood?

Accepted Answer

The activated charcoal filter of your Electrolux EFP60460OX hood is not washable and not regenerable. It must therefore be systematically replaced, not cleaned. It cannot be regenerated in the oven or by any other means.

Replacement frequency: The charcoal filter should be changed every four months at most. This duration varies depending on your usage: if you cook frequently, the filter will saturate more quickly. The saturation state of the activated charcoal also depends on the regularity of cleaning the grease filter, which plays a preliminary role in filtration. A regularly maintained grease filter extends the life of the charcoal filter.

Before you begin: Completely disconnect the hood from the electrical circuit by removing the plug or turning off the main switch of your home. Wait a few minutes for the motor to stop completely.

Removal and replacement: Access the charcoal filter located inside the hood. Generally, you need to press firmly on the sides of the filter or on the fastening clips to release the filter, then pull it towards you. The filter should detach with a dry sound (“Clack”). Insert the new filter in the reverse direction by sliding it into its housing until it clicks securely (you will hear a confirmation click). Ensure that the filter is properly in place before reconnecting the hood.

Warning: Strictly follow these instructions for regular filter replacement. Neglecting filter maintenance creates a fire risk and can damage the motor. Electrolux disclaims any responsibility for damages or incidents related to insufficient maintenance.

Spare parts: To purchase the original activated charcoal filter suitable for your EFP60460OX model, visit www.electrolux.com/shop. Only use original spare parts to ensure the effectiveness of filtration and the safety of your appliance. You can also register your hood at www.electrolux.com/productregistration for easy access to accessories and support.

User manual ELECTROLUX Range hood : user manuals and guides in PDF

Models ELECTROLUX Range hood most viewed

Other categories ELECTROLUX

Recent questions about Range hood ELECTROLUX