Q: How to install a charcoal filter on the ELECTROLUX LFP716X hood?

Replacing the ELECTROLUX LFP716X charcoal filter Installing a charcoal filter on your ELECTROLUX LFP716X hood is a simple operation that effectively filters cooking odors. This operation should be performed at least every four months depending on the type of cooking and frequency of use. Before you begin: Ensure that the hood is turned off and unplugged for safety reasons. Steps to remove the old filter: Remove the grease filters from the appliance by following the specific instructions for this model (refer to the section "Cleaning the grease filter") Pull the tabs towards the bottom of the charcoal filter Gently tilt the front of the filter downwards, then pull it out completely Steps to install the new filter: Position the new charcoal filter by following the same procedure in reverse order Insert the bottom part of the filter first, then lift the front part until it is securely in place Replace the grease filters on the hood Important information: The charcoal filter is an optional accessory, mainly used when the hood operates in air recycling mode. Depending on the type of filter provided with your appliance, it may be disposable or regenerable (cleanable); refer to the instructions included with the filter for the exact type. A LED alert signal will blink red twice per second for 30 seconds if the charcoal filter needs to be replaced or cleaned.

Question 1

How to wire and connect the Electrolux CE6010GR hood to electricity?

Accepted Answer

The Electrolux CE6010GR hood operates on an electrical supply of 220-240 V with mandatory grounding. This grounding must comply with current standards to ensure your safety: check that the domestic electrical installation has a properly connected ground before making the connection.

Installation of the bipolar switch: The connection to electricity must be made by interposing a bipolar switch with a contact opening of at least 3 mm. This switch allows for complete disconnection of the hood's power supply, ensuring total disconnection from the electrical network. Do not connect the hood directly to a power outlet.

Verification before installation: Before proceeding with the connection, check that the voltage of your electrical network (indicated on the rating plate affixed inside the hood) matches your domestic supply (220-240 V). This verification is crucial to avoid any malfunction or damage to the appliance.

Maintenance of the power cord: If the cord or power cable is damaged, it must be replaced exclusively by the manufacturer Electrolux or by an authorized after-sales service. Never attempt to repair a defective cable yourself, as this poses serious risks of electrocution. Professional repair ensures compliance and safety of the installation.

Commissioning: Once the bipolar switch is installed and the grounding verified, the hood is ready to be commissioned. The three motor speeds and lighting can then be controlled via the mechanical switches on the control panel. For more details on other installation elements (extraction ducting, mounting height), refer to the complete product manual.

Question 2

How do I change the activated charcoal filter in my hood?

Accepted Answer

The activated charcoal filter in your Electrolux EFP60460OX hood must be replaced regularly as it is not washable and not regenerable.

Filter Replacement

Recommended frequency: Replace the charcoal filter at most every four months. The saturation of the filter depends on the frequency of use and the regularity of cleaning the grease filter.

To obtain the original replacement filter suitable for your EFP60460OX model, visit www.electrolux.com/shop where you will find the appropriate accessories and original parts.

Replace the filter as soon as it is saturated or its absorption efficiency decreases, to maintain good odor absorption.

Question 3

How do I change the activated charcoal filter of my hood?

Accepted Answer

The activated charcoal filter of your Electrolux EFP60460OX hood is not washable and not regenerable. It must therefore be systematically replaced, not cleaned. It cannot be regenerated in the oven or by any other means.

Replacement frequency: The charcoal filter should be changed every four months at most. This duration varies depending on your usage: if you cook frequently, the filter will saturate more quickly. The saturation state of the activated charcoal also depends on the regularity of cleaning the grease filter, which plays a preliminary role in filtration. A regularly maintained grease filter extends the life of the charcoal filter.

Before you begin: Completely disconnect the hood from the electrical circuit by removing the plug or turning off the main switch of your home. Wait a few minutes for the motor to stop completely.

Removal and replacement: Access the charcoal filter located inside the hood. Generally, you need to press firmly on the sides of the filter or on the fastening clips to release the filter, then pull it towards you. The filter should detach with a dry sound (“Clack”). Insert the new filter in the reverse direction by sliding it into its housing until it clicks securely (you will hear a confirmation click). Ensure that the filter is properly in place before reconnecting the hood.

Warning: Strictly follow these instructions for regular filter replacement. Neglecting filter maintenance creates a fire risk and can damage the motor. Electrolux disclaims any responsibility for damages or incidents related to insufficient maintenance.

Spare parts: To purchase the original activated charcoal filter suitable for your EFP60460OX model, visit www.electrolux.com/shop. Only use original spare parts to ensure the effectiveness of filtration and the safety of your appliance. You can also register your hood at www.electrolux.com/productregistration for easy access to accessories and support.

Question 4

How to install a charcoal filter on the ELECTROLUX LFP716X hood?

Accepted Answer

Replacing the ELECTROLUX LFP716X charcoal filter

Installing a charcoal filter on your ELECTROLUX LFP716X hood is a simple operation that effectively filters cooking odors. This operation should be performed at least every four months depending on the type of cooking and frequency of use.

Before you begin: Ensure that the hood is turned off and unplugged for safety reasons.

Steps to remove the old filter:

Remove the grease filters from the appliance by following the specific instructions for this model (refer to the section "Cleaning the grease filter")
Pull the tabs towards the bottom of the charcoal filter
Gently tilt the front of the filter downwards, then pull it out completely

Steps to install the new filter:

Position the new charcoal filter by following the same procedure in reverse order
Insert the bottom part of the filter first, then lift the front part until it is securely in place
Replace the grease filters on the hood

Important information: The charcoal filter is an optional accessory, mainly used when the hood operates in air recycling mode. Depending on the type of filter provided with your appliance, it may be disposable or regenerable (cleanable); refer to the instructions included with the filter for the exact type. A LED alert signal will blink red twice per second for 30 seconds if the charcoal filter needs to be replaced or cleaned.

Question 5

How to replace the activated carbon filters on the Electrolux LFP316X hood?

Accepted Answer

Replacing the activated carbon filters on the Electrolux LFP316X hood is an important operation to maintain good suction efficiency and optimal air quality.

Replacement Frequency

The activated carbon filters should be replaced at most every 4 months. This frequency may vary depending on the use of the hood and the frequency of cleaning the grease filters.

Replacement Procedure

The activated carbon filters cannot be washed or regenerated.
The replacement is not a do-it-yourself operation as it requires the intervention of an authorized Electrolux technical service center.
It is recommended to contact customer service or an authorized assistance center to carry out this operation safely and ensure the proper functioning of the hood.

Additional Tips

To extend the life of the activated carbon filters, make sure to regularly clean the grease filters according to the manufacturer's instructions.

Question 6

Can the ELECTROLUX LFG337S kitchen hood be used with both filters and a ventilation duct?

Accepted Answer

No, the ELECTROLUX LFG337S hood cannot operate simultaneously with filters and a ventilation duct. You must choose one of the two modes and configure the hood accordingly.

Filter mode: The hood uses washable metal grease filters and an activated carbon filter to purify the air before releasing it back into the room. This mode is ideal if you cannot install a ventilation duct to the outside. The grease filters should be cleaned every 2 months at a minimum, and the carbon filter replaced every 4 to 6 months of use (more frequently depending on usage intensity).

Ventilation mode: The hood is connected to a ventilation duct that extracts stale air directly to the outside. This mode is generally more effective at completely eliminating odors and steam, as the air is not recirculated. In this case, filters are not used, and only the grease filter protects the motor.

The choice of mode depends on your kitchen setup and must be decided before installation. You cannot switch from one mode to another without modifying the hood. Once the mode is selected, configure the device accordingly to ensure optimal and safe operation.

Question 7

How to solve the problem of the knob that turns freely and prevents turning off the ELECTROLUX EFP126X extractor hood?

Accepted Answer

If the knob of your ELECTROLUX EFP126X hood turns freely and does not stop the device, it means that the internal control mechanism is not properly engaged. This hood has a retractable knob: it must be pressed to extend and make contact with the internal system. Here’s how to diagnose and resolve this issue.

Checking the retractable mechanism: Start by turning off the hood by unplugging it from the power outlet. Carefully examine the knob: it should push in and pop out correctly. Press firmly on the knob to check that it returns to its resting position. If it remains pressed or conversely does not retract, this indicates a mechanical blockage. Also inspect the end of the knob and the opening into which it fits for debris, kitchen residues, or hardened grease. Gently clean with a damp cloth if necessary.

Correctly reinserting the knob: After cleaning, the knob should partially push into the control panel and pop out freely. If it moves sideways or does not turn with gradual resistance, the internal mechanism may be disengaged. Try readjusting it by turning it slightly (clockwise or counterclockwise) while gently pressing it to correctly reinsert it into its housing.

Positioning to turn off the device: Normally, the off position (off position) is marked on the control panel. Press the knob and turn it until you reach this closed position. If it still turns without resistance and does not stop the hood, the internal contact mechanism is faulty and can no longer transmit commands to the device.

Emergency solution and service contact: While waiting for a repair, unplug the hood from the 220-240 V wall outlet to turn it off immediately. Since the problem concerns an electromechanical component (the internal rotary switch) that controls the power and speed of the ventilation, this type of fault cannot be resolved by the user. Contact an authorized Electrolux repair service mentioning model EFP126X and the specific problem of the knob turning freely. This component will need to be replaced to restore normal operation.

Question 8

What should I do if speed 2 of my ELECTROLUX LFV429K hood is not working while the other speeds are functioning?

Accepted Answer

If speed 2 of your ELECTROLUX LFV429K kitchen hood is not working while the other speeds are functioning normally, here are some steps to follow to identify and possibly resolve the issue:

1. Check the filters

Make sure that the grease filters are not clogged or heavily soiled, as this can affect the operation of the speeds. Clean or replace the filters if necessary.

2. Check the control panel

Check that the button or control corresponding to speed 2 is functioning correctly and is not damaged. Sometimes, a faulty contact can prevent this speed from being activated.

3. Check the internal electrical connections

A poor contact or a loose connection inside the hood can prevent speed 2 from working. If you are comfortable with electricity, you can check the internal connections; otherwise, consult a professional.

4. Reset the hood

Unplug the hood for a few minutes and then plug it back in. This operation may reset the electronic system and resolve some temporary malfunctions.

5. Technical support

If after these checks speed 2 still does not work, it is advisable to contact a customer service or a qualified technician for a more in-depth diagnosis and possible repair.

Question 9

How to remove the bulb cover from the ELECTROLUX LFP229X kitchen hood?

Accepted Answer

To remove the bulb cover from your ELECTROLUX LFP229X kitchen hood, follow these simple steps:

1. Safety first

Make sure the hood is unplugged or that the power supply is turned off to avoid any risk of electric shock.

2. Locate the bulb cover

The cover is usually located under the hood, just above the bulbs.

3. Removing the cover

Clip-on cover: Gently press on the sides or underneath the cover to release it. You may need to make a slight lever movement carefully.
Screwed cover: If the cover is secured with screws, use a suitable screwdriver to unscrew them before removing the cover.

4. Accessing the bulbs

Once the cover is removed, you can access the bulbs to replace or clean them.

5. Replacing the cover

After your intervention, reposition the cover by clipping it back on or screwing it in place depending on the type of fastening.

This procedure allows you to easily access the bulbs of your ELECTROLUX LFP229X hood while ensuring your safety.

Question 10

How to change the filter of the ELECTROLUX EFC90465OX extractor hood?

Accepted Answer

To change the filter of your ELECTROLUX EFC90465OX extractor hood, follow these simple steps:

Steps to replace the filter

Unplug the hood: Make sure the appliance is disconnected from the power supply to ensure your safety.
Access the filter: Open the panel located under the hood. Depending on the model, this may require unclipping a panel or unscrewing a few screws.
Remove the old filter: Carefully remove the used filter. Filters can be charcoal or metal, usually clipped or slid into a holder.
Install the new filter: Insert the new filter into the designated location, ensuring it is securely fixed and properly positioned.
Close the panel: Replace the panel or cover and secure it if necessary.
Plug the hood back in: Reconnect the appliance and check that it is functioning correctly.

Tip: Replace filters regularly, depending on your hood usage, to ensure optimal efficiency and good air quality.

User manual ELECTROLUX Basket : user manuals and guides in PDF

Models ELECTROLUX Basket most viewed

Other categories ELECTROLUX

Recent questions about Basket ELECTROLUX