TE-CC 1825 U - Saw EINHELL - Free user manual and instructions

USER MANUAL TE-CC 1825 U EINHELL

1. Safety regulations
2. Layout and items supplied
3. Proper use
4. Technical data
5. Before starting the equipment
6. Assembly
7. Operation
8. Operation
9. Replacing the power cable
10. Cleaning, maintenance and ordering of spare parts
11. Disposal and recycling
12. Storage

GB

Caution - Read the operating instructions to reduce the risk of inquiry

Wear ear-muffs. The impact of noise can cause damage to hearing.

Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!

Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.

Important. Risk of injury! Do not reach into the running saw blade.

GB

Important!

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be found in the enclosed booklet.

Caution!

Read all safety regulations and instructions. Any errors made in following the safety regulations and instructions may result in an electric shock, fire and/or serious injury.

Keep all safety regulations and instructions in a safe place for future use.

2. Layout and items supplied

2.1 Layout (Fig. 1-9)

1. Saw table
2. Splitter
3. Cover for extractor connection
4. Saw blade guard
5. Saw blade
6. Stop rail (parallel stop)
7. Parallel stop
8. Width extension, left
9. Guide rail for parallel stop
10. Width extension, right
11. Clamp lever for parallel stop
12. Scale for saw blade angle
13. Adjustment lever for cutting height
14. Setting wheel for saw blade angle
15. Setting screw
16. Leg
17. Rubber foot (type A)
18. Cross strut, bent type
19. Plate
20. Cross strut, straight type
21. Rubber foot (type B)
22. Adjustment lever 45^ - 47^
23. Adjustment lever -2° - 0°

24. Locking button for table width extension, left

25. Locking lever for table width extension, right

26. Transport handle
27. Stop rail for angle stop
28. Angle stop
29. Push stick
30. Key for changing the saw blade
31. Open-ended spanner 10mm / 13mm
32. Hex screw, short
33. Hex screw, medium
34. Hex screw, long
35. Washer
36. Self-locking nut
37. Slide
38. Locking lever for slide
    39.Wheel
39. Axle
40. Axle holder
41. Extractor connection (housing)
42. Table insert
43. Locking lever for saw blade angle
44. On/Off switch
45. Overload switch
46. Scale
47. Groove
48. Locking grip
49. Locking button
50. Nut, fl at

2.2 Items supplied

Please check that the article is complete as spcified in the scope of delivery. If parts are missing, please contact our service center or the nearest branch of the DIY store where you made your purchase at the latest within 5 work days after purchasing the article and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the warranty provisions at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
  If possible, please keep the packaging until the end of the guarantee period.

Important!

The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

GB

• Splitter
  Saw blade guard
• Stop rail (parallel stop)
• Parallel stop
  Leg (3x without setting screw, 1x with setting screw)
  Rubber foot, type A (2x)
• Rubber foot, type B (2x)
  Cross strut, bentype (2x)
  Plate
  Cross strut, straight type (2x)
  Transport handle (2x)
• Stop rail for angle stop
  Angle stop
  Push stick
  Key for changing the saw blade
• Open-ended spanner 10mm / 13mm
• Hex screw, short (4x)
• Hex screw, medium (28x)
• Hex screw, long (8x)
• Washer (40x)
• Nut, flat (4x)
  Self-locking nut (28x)
• Axles with wheels and axle holder (pre-assembled)
  Original operating instructions
  Safety information

3. Proper use

The format circular saw is designed for the slitting and cross-cutting (only with the cross stop) of all types of timber commensurate with the machine's size. The equipment is not to be used for cutting any type of round wood.

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

The equipment is to be operated only with suitable saw blades (saw blades made of HM or CV) It is prohibited to use any type of HSS saw blade and cutting-off wheel.

To use the equipment properly you must also observe the safety information, the assembly instructions and the operating instructions to be found in this manual.

All persons who use and service the equipment have to be acquainted with these operating instructions and must be informed about the equipment's potential hazards. It is also imperative to observe the accident prevention regulations in force in your area. The same applies for the general rules of health and safety at work.

The manufacturer will not be liable for any changes made to the equipment nor for any damage resulting from such changes. Even when the equipment is used as prescribed it is still impossible to eliminate certain residual risk factors.

The following hazards may arise in connection with the machine's construction and design:

• Contact with the saw blade in the uncovered saw zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces.
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw blade.
• Damage to hearing if essential ear-muffs are not used.
• Harmful emissions of wood dust when used in closed rooms.

GB

4. Technical data

Mains voltage. 230 V ~ 50Hz
Power P .S1 1500 W S6 40% 1800 W
Idle speed n_0 4,500 min-1
Carbide blade .0 250 x 0 30 x 3 mm
Number of teeth .48
Table size .625 x 500 mm
Table size with width extensions .625 x 740 mm
Max. cutting height .75 mm / 90° .53 mm / 45°
Height adjustment .infine 0 - 75 mm
Tilting saw blade .infine -2° - 47°
Extractor socket .0 36 mm
Weight approx. 27 kg

Sound and vibration

Sound and vibration values were measured in accordance with EN 61029.

Operation

LpA sound pressure level 98,5 dB(A)
Kuncertainty .3dB
LWA sound power level 109,4 dB(A)
Kuncertainty .3dB

The quoted values are emission values and not necessarily reliable workplace values. Although there is a correlation between emission and immission levels it is impossible to draw any certain conclusions as to the need for additional precautions. Factors with a potential influence on the actual immission level at the workplace include the duration of impact, the type of room, and other sources of noise etc., e.g. the number of machines and other neighboring operations. Reliable workplace values may also vary from country to country. With this information the user should at least be able to make a better assessment of the dangers and risks involved.

Wear ear-muff s.

The impact of noise can cause damage to hearing.

Keep the noise emissions and vibrations to a minimum.

Only use appliances which are in perfect working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
- Have the appliance serviced whenever necessary.
- Switch the appliance off when it is not in use.

Residual risks

Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment's construction and layout:

1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

5. Before starting the equipment

Before you connect the equipment to the mains supply make sure that the data on the rating plate are identical to the mains data.

Always pull the power plug before making adjustments to the equipment.

• Unpack the format circular saw and check it for damage which may have occurred in transit.
• Make sure the machine stands securely, i.e. bolt it to a workbench or solid base.
• All covers and safety devices have to be properly fitted before the equipment is switched on.
  It must be possible for the blade to run freely.
• When working with wood that has been processed before, watch out for foreign bodies such as nails or screws, etc.
  Before you actuate the On/Off switch, make sure that the saw blade is correctly fitted and that the equipment's moving parts run smoothly.

GB

6. Assembly

Important. Always screw together the connections which have self-locking nuts (see. Fig. 3, Item 36) by turning the hex screw while holding the self-locking nut firmly to fasten tightly.

6.1 Assembling the base frame (Fig. 1, 8-14)

• Turn the format circular saw upside down and place it on the floor.
  One of the legs (16) has a mount for the setting screw (15). Screw the setting screw in this mount. Use the leg with the setting screw as one of the front legs; it will then be readily accessible for fine adjustments.
  Use the hex screws (34), washers (35) and nuts (36) to fasten the two front legs (16) loosely to the front of the saw.
  Use the hex screws (34), washers (35) and nuts (36) to fasten the two back legs (16) loosely to the back of the saw.
  Use the hex screws (33), washers (35) and nuts (36) to fasten all four legs to the sides of the machine.
• Mount the rubber feet (17, 21) on the legs.
  Use the hex screws (33), washers (35) and nuts (36) to screw the cross struts (20) loosely to the legs.
• Screw the plate (19) to the bent cross struts (18), then screw the bent cross struts loosely to the legs. If necessary, adjust the cross struts (18) by bending with your hands so that the holes in the plate (19) coincide with those in the cross struts (18).
  Use the screws (33) and washers (35) to screw the axle holders (41) to the rear legs such that they point towards the rear of the machine and touch the ground.
  Use the screws (32), washers (35) and nuts (51) to screw the transport handles (26) to the feet at the front of the machine.
• Align the table so that it is level and tighten all the nuts and screws.

6.2 Fitting and setting the splitter (Fig. 15a, 15b)

• Important. Pull out the power plug.
  Take out the table insert (43) (see 6.4).
• Slacken the screw (z) for mounting the splitter.
• Insert the splitter (2) in the provided holder.
• Set the blade (5) to max. cutting depth, move to 0^ position and lock in place.
• Push up the splitter (2) until the gap between

the saw table (1) and the upper edge of the splitter equals approx. 10cm .

The distance between the blade (5) and the splitter (2) should be 3 - 5mm
- Tighten the screw (z) and mount the table insert.

6.3 Fitting the saw blade guard (Fig. 1, 16)

• Fit the saw blade guard (4) in the oval hole (y) in the splitter. Fasten the saw blade guard using the screw (x) and tighten the screw only enough to allow the saw blade guard to move still.
  The saw blade guard must always be lowered over the workpiece before you begin to cut.
  To connect the suction hose of an extraction system, the cover (3) on the saw blade guard can be removed (suction hose/extraction system not included).
  The machine is not allowed to be used without the saw blade guard.

6.4 Replacing the table insert (Fig. 17)

The table insert has to be opened if you need to replace it if it gets damaged and whenever you change the blade or set the splitter.
- To prevent increased likelihood of injury, you should replace the table insert whenever it is worn or damaged.
Important.Pull out the power plug.
- Remove the saw blade guard (4).
- Remove the countersunk head screws on the table insert.
Take out the table insert (43).
- Fit the replacement table insert by following the above in reverse.

6.5 Fitting/replacing the blade (Fig. 18)

Important. Pull out the power plug.
Always wear gloves when handling saw blades. Risk of injury!
- Remove the table insert by undoing the two countersunk head screws (see 6.4).
- Undo the nut with the one wrench (30) on the nut itself and an open-ended wrench (31) on the motor shaft to apply counter-pressure.
- Important. Turn the nut in the direction of rotation of the saw blade.
Take off the outer flange and pull the old saw blade off the inner flange by dropping the blade at an angle.
Clean the blade flange thoroughly before fitting the new blade.
- Mount and fasten the new saw blade in reverse order. Important. Note the running

GB

direction. The cutting angle of the teeth must point in running direction, i.e. forwards (see the arrow on the blade guard).

• Refit and set the splitter (2) and the saw blade guard (4) (see 6.2., 6.3.)
• Check to make sure that all safety devices are properly mounted and in good working condition before you begin working with the saw again.

7. Operation

7.1.ON/OFF switch and overload switch (Fig. 7)

To turn the saw on, press the green button "I". Wait for the blade to reach its maximum speed of rotation before commencing with the cut.
To turn the equipment off again, press the red button 0^#

The motor of this equipment is protected against overload by an overload switch (46). If the rated current is exceeded, the overload switch (46) will shut down the equipment.

• Let the equipment cool down for several minutes.
  Press the overload switch.
• Press the green button, I^k to switch on the equipment.

7.2.Cutting depth (Fig.1)

Turn the hand crank (13) to set the blade (5) to the required cutting depth.

Turn anti-clockwise:

smaller cutting depth

Turn clockwise:

larger cutting depth

7.3. Parallel stop

7.3.1. Stop height (Fig. 21, 22)

• Push the stop rail (6) onto the parallel stop (7)
• The parallel stop (7) supplied with the bench-type circular saw has two different guide faces.
• For thick material you must use the stop rail (6) as shown in Fig. 21, for thin material you must use the stop rail as shown in Fig. 25.
  To change over the stop rail (6) you have to slacken the two knurled screws (w) in order to

disconnect the stop rail (6) from the parallel stop (7).

Depending on the required cutting height, the stop rail can be slid into two different grooves on the parallel stop and secured with the knurled screws.
- The stop rail can be taken off and fastened to either the right or left parallel stop depending on the purpose.
The parallel stop is set at right-angles to the guide rail at the factory. It can be readjusted using two Allen screws (in the parallel stop).
If you need to readjust the parallel stop: Slacken the screws (u) on the parallel stop (7). Adjust the parallel stop so that it is parallel to the saw blade (5) or vertical to the guide rail (9). Retighten the screws (u).

7.3.2.Cutting width (Fig.1, 21, 22)

The parallel stop (7) has to be used when making longitudinal cuts in wooden workpieces.
The parallel stop (7) can be mounted on either side of the saw table (1).
The parallel stop (7) has to be mounted in the guide rail (9) of the saw table (1).
The parallel stop (7) can be set to the required dimension with the help of the scale (47) on the guide rail (1).
- You can clamp the parallel stop in the required position by pressing the lever (11).

7.3.3. Table width extension left/right and scale (Fig. 6a, 6b, 23-26)

• To pull out the left table width extension (8), open the locking buttons (24) at the front and rear on the bottom side of the table. Then pull the table width extension to the left and secure the locking buttons again.
• To pull out the right table width extension (10), open the locking buttons (25) at the front and rear on the bottom side of the table. Then pull the table width extension to the right and secure the locking buttons again.
  The right table width extension has a traveling scale indicator. The scale has a total of four different readings for the high and low adjustment of the parallel stop (see 7.3.1), each with a retracted and extended table.
• With the right table width extension retracted, the width set at the parallel stop can be read off the lower scale row. It is indicated by the pointer (a) of the stop rail. The lower scale row has two lines, marked for the high and low setting of the parallel stop (see 7.3.1)

GB

• With the right table width extension extended, the upper scale row applies: Secure the stop rail with pointer (a) at the end point of the lower scale row. The end points are 25cm for the low parallel stop and 30cm for the high parallel stop. The value of the total width can now be read off the upper scale row at indicator (b). The maximum value is 47cm (with the parallel stop set low) or 52cm (with the parallel stop set high).

7.3.4. Setting the stop length (Fig. 27)

• The stop rail (6) can be moved in longitudinal direction in order to prevent the workpiece from becoming jammed.
• Rule of thumb: The rear end of the stop comes up against an imaginary line that begins roughly at the center of the blade and runs at an angle of 45^ to the rear.
• Set the required cutting width
• Slacken the knurled screws (w) and push the stop rail (6) forward until it touches the imaginary 45^ line.
• Retighten the knurled screws (w).

7.4. Angle stop (Fig. 19)

• Push the stop rail (27) onto the angle stop (28)
• Slide the angle stop (28) into the groove (48) of the saw table.
• Undo the locking grip (49).
• Turn the stop rail (27) until the arrow points to the angle required.
• Re-tighten the locking grip (49).

Important.

• Do not push the stop rail (27) too far toward the blade.
  The distance between the stop rail (27) and the blade (5) should be approx. 2cm

7.5. Setting the angle (Fig. 5)

• Undo the locking grip (44) by turning it counter-clockwise. To have enough room for adjustment, the locking lever can be disengaged by pulling (similar to a ratchet).
• Undo the locking grip (44).
• Turn the wheel (14) to set the desired angle on the scale.

• Secure the locking grip in the required angle position.
  For angles between -2^ and 0^ open the adjustment lever (22) at the front of the machine in order to release the setting wheel (14) for this angle range.

• Similarly for angles between -45^ and 47^ open the adjustment lever (23) at the front of the machine.

• Secure the locking grip (44) by turning it clockwise.

8. Operation

Important!!

After every new adjustment we recommend you to make a trial cut in order to check the new settings.
If you discover a deviation on a trial cut, you can adjust the indicator of the scale (a) at the parallel stop or at the table (b) by undoing their screws.
After switching on the saw, wait for the blade to reach its maximum speed of rotation before commencing with the cut.
Take extra care when starting the cut!
- Never use the equipment without the suction function.
Regularly check and clean the suction channels.

8.1. Making longitudinal cuts (Figure 29)

Longitudinal cutting (also known as slitting) is when you use the saw to cut along the grain of the wood. Press one edge of the workpiece against the parallel stop (7) while the fl at side lies on the saw table (1). The blade guard (4) must always be lowered over the workpiece. When you make a longitudinal cut, never adopt a working position that is in line with the cutting direction.

• Set the parallel stop (7) in accordance with the workpiece height and the desired width. (See 7.3.)
• Switch on the saw.
• Place your hands (with fingers closed) flat on the workpiece and push the workpiece along the parallel stop (7) and into the blade (5).
  Guide at the side with your left or right hand (depending on the position of the parallel stop) only as far as the front edge of the guard hood.
  Always push the workpiece through to the end of the splitter (2).
  The offcut piece remains on the saw table (1) until the blade (5) is back in its position of rest.
• Secure long workpieces against falling off at the end of the cut (e.g. with a roller stand etc.)

GB

8.1.2. Cutting narrow workpieces (Fig. 30) Be sure to use a push stick (29) when making longitudinal cuts in workpieces smaller than 120 mm in width. A push stick is supplied with the saw! Replace a worn or damaged push stick immediately.

8.1.3.Cutting very narrow workpieces (Fig. 31)

• Be sure to use a push block when making longitudinal cuts in very narrow workpieces with a width of 30mm and less.
  The low guide face of the parallel stop is best used in this case.
  There is no push block supplied with the saw! (Available from your specialist dealer) Replace the push block without delay when it becomes worn.

8.1.4. Making angular cuts (Fig. 32)

Angular cuts must always be used using the parallel stop (7).

• Set the blade (5) to the desired angle. (See 7.5.)
• Set the parallel stop (7) in accordance with the workpiece width and height (see 7.3.1)
• Carry out the cut in accordance with the workpiece width (see 8.1.1., 8.1.2 and 8.1.3.)

8.1.5. Making cross cuts (Fig. 33)

• Slide the angle stop (28) together with the stop rail (27) into one of the grooves in the saw table (1) and adjust to the required angle. (See 7.4.) If you also want to tilt the blade (5), use the groove which prevents your hand and the cross stop from making contact with the blade guard.
  If necessary, position the stop rail (27) so that it cannot collide with the saw blade when you make your cut.
• Press the workpiece firmly against the stop rail (27).
• Switch on the saw.
• Push the angle stop (28) and the workpiece toward the blade in order to make the cut.
• Important: Always hold the guided part of the workpiece. Never hold the part which is to be cut off.
• Push the angle stop (28) forward until the workpiece is cut all the way through.
• Switch off the saw again. Do not remove the offcut until the blade has stopped rotating.

8.2 Working with the slide

8.2.1 Releasing the slide (Fig. 5, 20)

Open the two locking levers (38).
- Secure the angle stop (28) with the locking button (50) at the front end of the slide (37).

8.2.2 Making cuts with the help of the sliding table (Fig. 28)

• Set the angle stop to the required angle value.
• Press the workpiece firmly against the stop rail (27) and push the sliding table slowly toward the blade.
• Push the sliding table forward until the workpiece is cut all the way through.
• Switch off the saw again. Important: Do not remove the offcut until the blade has stopped rotating.

9. Replacing the power cable

If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.

10. Cleaning, maintenance and ordering of spare parts

Always pull out the mains power plug before starting any cleaning work.

10.1 Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
  We recommend that you clean the device immediately each time you have finished using it.
  Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

GB

10.2 Carbon brushes

In case of excessive sparking, have the carbon brushes checked only by a quali edlectrician. Important! The carbon brushes should not be replaced by anyone but a quali edlectrician.

10.3 Maintenance

There are no parts inside the equipment which require additional maintenance.

10.4 Transport

For transporting, lift the saw table slightly by the transport handles (26) so that it can be moved on the rollers.
- Transport the machine only when the safety devices and blade guard are fitted.
- Secure the equipment against slipping; tie it down securely.

10.5 Ordering replacement parts:

Please quote the following data when ordering replacement parts:

Type of machine
Article number of the machine
- Identification number of the machine
- Replacement part number of the part required

For our latest prices and information please go to www.isc-gmbh.info

11. Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.

12. Storage

Store the equipment and accessories out of children's reach in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30^ . Store the electric tool in its original packaging.

GB

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

GB

Warranty provisions

iSC GmbH or the DIY store where you made you purchase guarantees the repair of defects or replacement of the equipment in accordance with the overview below. Statutory guarantee claims are unaffected.

Category Example Warranty
Defect with regard to material or construction		24 months
Wear parts* V-belt, carbon brushes	es, table insert, push stick	6 months
Consumables* Saw blade Warranty only in case of an im-		mediate defect (24 hours after purchase / date on the bill)
Missing parts 5 work days

• Not necessarily included in the scope of delivery!

For consumables, wear parts and missing parts iSC GmbH guarantees the correction of defects or a new delivery only if the defect is reported within 24 hours (consumables), 5 work days (missing parts) or 6 months (wear parts) after purchase and the purchase date is verified with the bill.

In case of defects concerning the material or construction, we kindly request you to submit the equipment together with the fully completed warranty card supplied with the equipment. It is important that you enter an exact description of the defect.

To do so, answer the following questions:

Did the equipment work at all or was it defective from the beginning?
Did you notice anything (symptom or defect) prior to the failure?
What malfunction does the equipment have in your opinion (main symptom)?

Describe this malfunction.

GB

Warranty certificate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under the service number printed below. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee.
2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The following are also excluded from our guarantee: compensation for transport damage, damage caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by the device being dropped) and normal wear resulting from proper operation of the device. This applies in particular to rechargeable batteries for which we nevertheless issue a guarantee period of 12 months. The guarantee is rendered null and void if any attempt is made to tamper with the device.
3. The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies when an on-site service is used.
4. In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if you could describe the nature of the problem in as much detail as possible. If the defect is covered by our guarantee then your device will either be repaired immediately and returned to you, or we will send you a new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.

Also refer to the restrictions of this warranty concerning wear parts/consumables and missing parts as set forth in the warranty conditions in these operating instructions.

F

Sommaire

Chere CLIENT, Cher Client

Uttag for spanutsugning 36 mm

Vikt ca 27 kg

S

MoC P. S1 1500 W S6 40% 1800 W

Stevilo vrtljajev prostem tekun.4500 min-1

Zagin list iz trde kovine ...0 250 x 0 30 x 3 mm

Stevilo zob 48

Velikost mize .625 x 500 mm

Velikost mize z razsrirvami .625 x 740 mm

Maksimalna visina reza .75 mm/90°

53 mm/45°

Nastavitev visine .brezstopenjsko 0 - 75 mm

Zagin list - premičen

vstran . -2° -47°

GB explains the following conformity according to EU directives and norms for the following product

Subject to change without notice

Archive-File/Record: NAPR003420

Documents registrar: Siegfried Roider

Wiesenweg 22, D-94405 Landau/Isar

EH 03/2013 (01)