G24LT30MK2 Akku-Rasentrimmer inkl. Akku 2.0Ah - Grass trimmer GREENWORKS - Free user manual and instructions

USER MANUAL G24LT30MK2 Akku-Rasentrimmer inkl. Akku 2.0Ah GREENWORKS

English (Original Instructions)

SPECIFICATIONS

Voltage 24 Volts
No Load Speed	9,000 - 10,000 rpm
Cutting head	Automatic feed
Cutting Line Diameter	1.65 mm
Cutting Path Diameter	250/300 mm
Measured sound pressure level	L_PA=82 dB(A), K_PA=3 dB(A)
Guaranteed sound power level	L_WA=96 dB(A),
Vibration	2 m / s ^2 , k=1.5
Battery pack	29807/29837/29697
Charger	29817/29827
Weight with battery pack	3.13 kg

ASSEMBLY

UNPACKING

This product requires assembly.

■ Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included.

WARNING

Do not use this product if any parts on the Packing List are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury.

■ Inspect the product carefully to make sure no breakage or damage occurred during shipping.
■ Do not discard the packing material until you have carefully inspected and satisfactorily operated the product.

WARNING

If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

WARNING

Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING

To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the product when assembling parts.

DESCRIPTION

1. Switch trigger
2. Rear handle
3. Lock-out trigger
4. Front handle
5. Upper shaft
6. Shaft coupler
7. Lower shaft
8. Plant protector
9. Grass deflector
10. Cutting diameter slide
11. Cutting line
12. Pivoting button
13. Edger wheel
14. Trimmer/Edger button
15. Battery pack
16. Charger

English

ATTACHING GRASS DEFLECTOR

See Figure 2.

WARNING

The line cut-off blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury.

■ Remove supplied screws from the motor housing.
■ Fit the grass deflector into the slots on trimmer head.
■ Turn counterclockwise to lock grass deflector into place.
■ Line up the screw holes in the grass deflector with the holes in the motor housing head.
■ Install supplied screws and tighten by turning clockwise with a phillips screwdriver.

OPERATION

WARNING

Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING

Always wear eye protection. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.

WARNING

Never use blades, flailing devices, wire, or rope on this product. Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

For complete charging instructions, refer to the Operator's Manuals for your battery pack and charger models.

NOTE: To avoid serious personal injury, always remove the battery pack and keep hands clear of the lock-out button when carrying or transporting the tool.

TO INSTALL BATTERY PACK

See Figure 3.

• Place the battery pack in the trimmer. Align raised ribs on battery pack with grooves in the trimmer's battery port.
  ■ Make sure the latch on bottom of the battery pack snaps in place and that battery pack is fully seated and secure in the trimmer before beginning operation.

TO REMOVE BATTERY PACK

See Figure 3.

■ Release the variable speed control trigger to stop the trimmer.
■ Press and hold the battery latch button at the bottom of the battery pack.
■ Remove battery pack from the trimmer.

SHAFT ASSEMBLY

See Figure 4.

The shaft's length cannot be adjusted.

■ Insert the lower shaft into the shaft coupler on the upper shaft.
■ Tighten the coupler by turning clockwise. Make sure the upper and lower part of shafts are securely tightened before reinstalling the battery pack.

STARTING/STOPPING THE TRIMMER

See Figure 5.

■ To start the trimmer, grip the front handle with one hand while holding the rear handle with your other hand making sure to depress the lock-out trigger while squeezing the variable speed trigger.
■ To stop the trimmer, just release the variable speed control trigger.

English

■ Hold the trimmer with your right hand on the rear handle and your left hand on the front handle.
- Keep a firm grip with both hands while in operation.
■ Trimmer should be held at a comfortable position with the rear handle about hip height.
- Cut tall grass from the top down. This will prevent grass from wrapping around the shaft housing and string head which may cause damage from overheating.

If grass becomes wrapped around the string head:

■ Remove the battery pack from the trimmer.

■ Remove the grass.

WARNING

Contact with the trimmer cutting head while operating can result in serious personal injury.

CUTTING TIPS

See Figure 8

• Keep the trimmer tilted toward the area being cut; this is the best cutting area.
  ■ The trimmer will cut better when moved from left right across the area to be cut; it is less effective when moved from right to left.
  ■ Use the tip of the cutting line to do the cutting; do not force cutting head into uncut grass.
  ■ Wire and picket fences cause extra cutting line wear, even breakage. Stone and brick walls, curbs, and wood may wear cutting line rapidly.
  ■ Avoid trees and shrubs. Tree bark, wood moldings siding, and fence posts can easily be damaged by the cutting line.

ADVANCING CUTTING LINE

NOTE: The trimmer is equipped with an auto-feed head. Bumping the head to try to advance the line will damage the trimmer and void the warranty.

■ With the trimmer running, release the switch trigger.
■ Wait two seconds, and press the switch trigger.

NOTE: The cutting line will extend approximately 0.635cm with each stop and start of the trigger until the cutting line reaches the length of the grass deflector cut-off blade.

■ Resume trimming.

ADVANCING THE CUTTING LINE MANUALLY

See Figure 7.

■ Remove the battery pack.
■ Push the black button located on the cutting head while pulling on cutting line to manually advance the cutting line.
■ After extending new cutter line, always return the machine to its normal operating position before switching on.

ADJUSTABLE CUTTING DIAMETER

See Figure 9.

■ Rotate the plant protector to its working position to avoid cutting flowers or plants by mistake.
■ Remove the battery pack.
■ Adjust the "cutting diameter slide" on the grass deflector to adjust the cutting path diameter. There are 2 diameter options: 30cm, 25cm.

Note: a smaller diameter cutting path will maximize run time and cutting speed, while a larger cutting path will help complete the trimming task quicker.

LINE CUT-OFF BLADE

See Figure 10.

This trimmer is equipped with a line cut-off blade on the grass deflector. For best cutting, advance line until it is trimmed to length by the line cut-off blade. Advance line to whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep line long enough to advance properly.

WARNING

When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING

To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.

GENERAL MAINTENANCE

Before each use, inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until all missing or damaged parts are replaced.

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of

English

commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING

Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at an Authorised Service Centre.

CHARGER AND BATTERY PACK

29697/29807- 24V 43Wh Lithium battery pack 29837- 24V 86Wh Lithium battery pack 29817/29827- 24V charger

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

Contact customer service for the latest replacement parts and accessories.

WARNING

Upon removal, cover the battery pack's terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Lithium-ion and nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

SPOOL REPLACEMENT

See Figure 12.

Use only 1.65 mm diameter monofilament cutting line. Use original manufacturer's replacement cutting line for best performance.

■ Remove the battery pack.
■ Push in tabs on side of spool cover.
■ Pull spool cover up to remove.
■ Remove the old spool.
■ To install the new spool, make sure the cutting line is captured in the slot on the new spool. Make sure the end of the cutting line is extended approximately 15cm beyond the slot.

■ Install the new spool so that the cutting line and slot align with the eyelet in the cutting head. Thread the cutting line into the eyelet.
■ Pull the cutting line extending from the cutting head so the cutting line releases from the slot in the spool.
■ Reinstall the spool cover by depressing tabs into slots and pushing down until spool cover clicks into place.

CUTTING LINE REPLACEMENT

See Figures 12 - 13.

■ Remove the battery pack.
■ Remove the spool from the cutting head.

NOTE: Remove any old cutting line remaining on the spool.

■ Cut a piece of cutting line approximately 3m long. Use only 1.65mm diameter monofilament cutting line.
■ Insert the cutting line into the anchor hole in the upper part of the spool. Wind the cutting line around the upper part of the spool clockwise, as shown by the arrows on the spool. Place cutting line in the slot on upper spool flange, leaving about 15cm. extended beyond the slot. Do not overfill. After winding the cutting line, there should be at least 0.635 cm between the wound cutting line and the outside edge of the spool.
■ Replace the spool, and the spool cover. Refer to spool replacement earlier in this manual.

STORING THE TRIMMER

■ Remove the battery pack from the trimmer before storing.
■ Clean all foreign material from the trimmer.
■ Store it in a place that is inaccessible to children.
- Keep away from corrosive agents such as garden chemicals and de-icing salts.
■ Store and charge your batteries in a cool area. Temperatures above or below normal room temperature will shorten battery pack life.

■ Never store batteries in a discharged condition. Wait for battery pack to cool and fully charge immediately.
■ Store the battery pack where the temperature is below 27^ C and away from moisture.
■ All batteries gradually lose their charge. The higher the temperature, the quicker they lose their charge. If you store your unit for long periods of time without using it, recharge the batteries every month or two. This practice will prolong battery pack life.

English

TROUBLESHOOTING

Problem Possible cause Solution
String will not advance when using the auto-feed head.	String is welded to itself. Lubricate with silicone spray.
	Not enough string on spool.	Install more string. Refer to string replacement earlier in this manual.
	String is worn too short. Pull string while pressing line release button.
	String is tangled on spool.	Remove string from spool and rewind. Refer to string replacement earlier in this manual.
Grass wraps around shaft housing and string head.	Cutting tall grass at ground level.	Cut tall grass from the top down to prevent wrapping.
Motor fails to start when switch trigger is depressed.	Battery is not secure.	To secure the battery pack, make sure the latch on bottom of the battery pack snaps into place.
	Battery is not charged.	Charge the battery pack according to the instructions included with your model.
	Shaft not connected completely.	Make sure lower shaft is fully seated in shaft coupler on upper shaft and secure shaft coupler.

Deutsch

SPEZIFIKATION

REPLACEMENT DE LA BOBINE

Cf. Figure 12.

Å SETTE PÅ GRESSAVELEDEREN

Se Figur 2.

ADVARSEL

FREMF∅RING AV SNOREN MANUELT

Se Figur 7.

GENERELT VEDLIKEHOLD

MANUEL FREMF∅RING AF TRÅDEN

Se Fig. 7.

INDSTILBAR KLIPPEDIAMETER

Se Fig. 9.

UDSKIFTNING AF SPOLE

Se Fig. 12.

Brug kun twist 1,5mm diameter monofilament-klippetråd.

■ Tag batteriet af.

ROZWIaZYWANIE PROBLEMÓW

■ Never store batteries in a discharged condition. Wait for battery pack to cool and fully charge immediately.

Greenworks Tools Warranty Policy for DIY machines

PERIOD OF WARRANTY

All new Greenworks Tools machinery is supplied with a 2 year parts and labour warranty from original date of purchase. A 30 day warranty is available for machines used professionally as Greenworks Tools are designed primarily to be used by DIY consumers. This warranty is non-transferable.

LIMITATIONS

This warranty applies only to defective parts/components and does not cover repairs due to:

1. Normal wear and tear.
2. Routine tune up or adjustment.
3. Damage caused by improper handling/abuse/misuse or neglect.
4. Overheating due to lack of maintenance.
5. Damage due to fittings/fasteners becoming loose/detached through lack of maintenance.
6. Damage caused by cleaning with water.
7. Machines serviced or repaired by non-authorised Greenworks Tools service centres.
8. Machines incorrectly assembled or adjusted.
9. Damage caused by improper use of the machine.
10. Damage caused by improper winterisation (pressure washers)
11. Items considered as consumable parts are not normally covered by the warranty, including but not limited to:

- Batteries

• Electric cables
• Blade and blade assemblies
• Belts
• Filters

• Chucks and tool holders

• Certain products may contain components such as engines, transmissions from an alternative manufacturer, these items will be subject to the appropriate manufacturer's warranty policy except where Greenworks Tools Europe GmbH agrees to underwrite any claims outside the said manufacturer's warranty period.

• Second hand goods are not covered under this warranty policy.
• The fitting of spares, replacements or extra components which are not supplied or approved by Greenworks Tools Europe GmbH.

Warranty

To claim a warranty on any product under this policy a proof of original purchase is required. Credit card statement do not qualify as sufficient proof of purchase. In the first instance of a warranty event occurring the consumer should return the product to the original place of purchase with their proof of purchase. The machine will be sent to our central service facility and an inspection made. If the machine be found to be at fault it will be repaired and sent back to the address of the consumer free of charge. Machines that retail for less than €100 euros including sales taxes will generally be replaced.

If the central service facility finds that machine is not found to be at fault then the consumer will be advised they will need to pay for the cost of the repair.

This warranty policy is subject to change from time to time to accommodate the needs of new products. A copy of the latest warranty policy will be available at www.greenworkstools.eu.

Greenworks Tools (DIY)

نامضلا قدم

"הכלהה" Greenworks Tools

תְקָרִי אַלְאָה

EC DECLARATION OF CONFORMITY FOR MACHINERY

Manufacturer: Changzhou Globe Co., Ltd.

Address: No.65 Xinggang Road Zhonglou Zone Changzhou, Jiangsu 213000

P.R.China

Name and address of the person authorised to compile the technical file:

Name: Gary Gao Naixin (Director of Outdoor Power Equipment)

Address: Greenworks Tools Europe GmbH

Wankelstrasse 40.

50996 Koln

Germany

Herewith we declare that the product

Category .....LINE TRIMMER

Model 21227

Serial number ...... See product rating label

Year of Construction ...... See product rating label

• is in conformity with the relevant provisions of the Machinery Directive (2006/42/EC)

- is in conformity with the provisions of the following other EC-Directive

2014/30/EU (EMC-Directive), and

2000/14/EC (Noise-Directive) incl. modifications (2005/88/EC)

And furthermore, we declare that

• the following (parts/clauses of) European harmonised standards have been used

EN60335-1, EN 50636-2-91, EN ISO 3744, ISO 11094, EN 55014-1, EN 55014-2

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Measured sound power level 93.3 dB(A)

Guaranteed sound power level 96 dB(A)

Conformity assessment method to Annex VI/ Directive 2000/14/EC

The notified body: Intertek Testing & Certification Ltd.

Address: Davy Avenue, kwowchill, Milton Keynes, MK5 8NL

Place, date: Changzhou, 02/09/2016

Signature: Gary Gao Naixin (BEng, CEng,

MIET) Vice president of Engineering

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Endereço: No.65 Xinggang Road Zhonglou Zone Changzhou, Jiangsu 213000

China

Máquinas (2006/42/EC)

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Naam: Gary Gao Naixin (Director of Outdoor Power Equipment)

Adres: Greenworks Tools Europe GmbH

Wankelstrasse 40.

50996 Koln

Germany

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Gemeten geluidsdrukniveau 93.3 dB(A)

Endereço: No.65 Xinggang Road Zhonglou Zone Changzhou, Jiangsu 213000

China

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Mitattu äänenteho 93.3 dB(A)

Adress: Greenworks Tools Europe GmbH

Wankelstrasse 40.

50996 Koln

Germany

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Målt lydeffektniveau 93.3 dB(A)

Garanteret lydeffektniveau 96 dB(A)

DEKLARACJA ZGODNOŚCI WE DLA MASZYN

Producent: Changzhou Globe Co., Ltd.

Adres: No.65 Xinggang Road Zhonglou Zone Changzhou, Jiangsu 213000 P.R. Chiny

TS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Izmjerena razina zvučne snage

93.3 dB (A)

Jamčena razina zvučne snage

96 dB (A)

Metoda procjene usklađenosti prema dodatkuvi/Direktive 2000/14/EC

Mjesto, datum: Changzhou, 02/09/2016

Potpis: Gary Gao Naixin (BEng,

CEng, MIET) Potpredsjednikinženjeringa

EK GÉPÉSZETI MEGFELELŐSÉGI NYILATKOZAT

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Adresă: No.65 Xinggang Road Zhonglou Zone Changzhou, Jiangsu 213000 China

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Измерено ниво на шум

93.3 dB(A)

Address: Greenworks Tools Europe GmbH

Wankelstrasse 40.

50996 Koin

Germany

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

No.65 Xinggang Road Zhonglou Zone Changzhou,

Jiangsu 213000 P.R.China.

:يَنْقُتُلَا فَلِجُلا عَمْجِب لُوْخُمْلَا صَخْشُلَا نَارِنْ عَرْ مَسَا

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

VI/ Directive 2000/14/EC

16 02/09/2016 : Gary Gao Naixin (دردنه سرويرولالكعب)

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Imza: Gary Gao Naixin (BEng, CEng,

Address: Greenworks Tools Europe GmbH

Wankelstrasse 40.

50996 Koln

תְקּרָה

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

אַלְרָה אַתִי:

93.3 dB(A)

בַרְשָׁה בִרְשָׁה

96 dB(A)

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Adrese: No.65 Xinggang Road Zhonglou Zone Changzhou, Jiangsu 213000

P.R.China

Adrese: Greenworks Tools Europe GmbH

Wankelstrasse 40.

50996 Koln

Germany

Ar šo mês paziņojam, ka prece

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Paraksts: Gary Gao Naixin (BEng,

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Mōōdetud helivōimsuse tase 93.3 dB(A)