Question 1

Can the GREENWORKS GD24RS saw cut metal?

Accepted Answer

Yes, the GREENWORKS GD24RS jigsaw can cut metal, as well as other materials like wood, plastic, and drywall.

This device is a 24V reciprocating saw with a maximum no-load speed of 2700 RPM and a stroke length of 28 mm, making it versatile for different types of cutting.

Usage tips for metal:

Do not apply excessive force. The manual states: “Do not force. Use only sufficient force.” Excessive pressure can bend or break the blade.
Securely clamp your metal workpiece in a vise before cutting, for safety and stability reasons.
Use a blade suitable for metal for optimal results.

Question 2

The mower starts but stops after a few seconds

Accepted Answer

Several factors can cause this quick stop on the GREENWORKS G24X2LM41 mower. Here are the checks to perform in order:

1. Battery condition

Even if the mower starts, a weak battery does not provide enough power to keep the motor running. The G24X2LM41 uses two combined 24V lithium-ion batteries (48V total). Check that both batteries are fully charged. A full charge lasts about 40 minutes with a new battery. If one battery is degraded, replace it.

2. Cutting height too low

The machine has 5 adjustable positions between 25 and 80 mm. If you have lowered the height too close to the ground, the blade immediately overloads the motor, which stops as a protection. Increase the cutting height by at least one notch and try again.

3. Debris stuck under the deck

Grass, leaves, or other debris stuck around the blade slow down or block the rotation. This causes the motor to overload and stop. Remove the battery, wait for the motor to come to a complete stop, and then carefully clean all debris from under the cutting deck.

4. Damaged or unbalanced blade

A bent or unbalanced blade causes excessive vibration and motor overload. Visually check that the blade is not twisted. If it is, it must be replaced. The recommended torque is 33-37 Nm.

In summary: Start by fully recharging both batteries, check that nothing is blocking the blade, and then increase the cutting height. These are the most common causes of this stop after 5 seconds.

Question 3

Why does my GREENWORKS GD24X2LM46SP mower start and then stop immediately even though the batteries indicate they are charged?

Accepted Answer

If your GREENWORKS GD24X2LM46SP mower starts and then stops immediately, even though the batteries indicate they are charged, it is usually due to a safety or contact issue. According to the technical manual, the dual-hand safety system of this mower prevents normal operation in case of doubt.

First, check the battery installation. Make sure that both 24V batteries are fully inserted into their respective compartments and that they are securely locked (you should hear an audible click). Also, check that the battery connectors and the receptacle slots are free from dust, corrosion, or debris that could create a poor contact. A poor electrical contact may give the impression that the battery is charged but prevent regular operation.

Check the bail switch. This essential safety element must remain pressed down constantly during operation. You need to hold the start button and then pull the bail switch towards the handlebar and keep it pressed down. If this switch is faulty or poorly engaged, the mower will stop immediately. Test if you feel any abnormal resistance or if the switch is "sticking".

Check the safety key. This key must be fully inserted for the motor to start. Even a slightly incomplete repositioning can cause an immediate stop. Remove it and reinsert it firmly, ensuring that it is properly in place.

Inspect the blades and the deck. Grass clippings, leaves, or debris stuck under the deck can block the blades or trigger immediate thermal protection. Although less likely at startup, a significant blockage can cause a very quick stop. Check the bottom of the deck and clear anything that could block the blades.

Let the machine cool down. If you have just used the mower or if the motor has overheated, an automatic thermal protection may cut off the motor. Wait 15 to 20 minutes before trying again. According to the manual, excessive operating temperature causes an automatic safety stop.

If the problem persists after these checks, the bail switch or an electronic safety component is likely faulty. Contact an authorized Greenworks service center for repair or replacement, especially if your machine is covered by the 2-year warranty.

User manual GREENWORKS : user manuals and guides in PDF

Models GREENWORKS most viewed

Browse manuals GREENWORKS by appliance type

Recent questions about devices GREENWORKS