GD24CS - Saw GREENWORKS - Free user manual and instructions

Name: GD24CS
Brand: GREENWORKS
Rating: 8.5 (95 reviews)

Find the device manual for free GD24CS GREENWORKS in PDF.

📄 120 pages

EN ⬇ Download 💬 AI Question ❓ 10 questions ⚙️ Specs

View the manual :

Pick your language and provide your email: we'll send you a specifically translated version.

This manual is not available in your language

Desired language Your email address

Product Type	Cordless Circular Saw
Brand	Greenworks
Model	GD24CS
Voltage	24 V
No-load Speed	4,500 min⁻¹
Blade Diameter	184 mm
Weight without Battery	3.35 kg
Max Cutting Depth at 0°	63 mm
Max Cutting Depth at 45°	43 mm
Adjustable Cutting Angle	Yes (0° to 45°)
Adjustable Depth	Yes
Edge Guide Included	Yes
Lower Guard	Yes
Spindle Lock	Yes
Compatible Battery	G24B2/G2, 4B4 and BAG series (24 V)
Compatible Charger	2913907 and CAG series
Sound Pressure Level	84.6 dB(A)
Sound Power Level	95.6 dB(A)
Vibration	< 2.5 m/s²
Product Warranty	3 years
Battery Warranty	2 years
Maintenance	Clean with a soft damp cloth; vacuum the vents
Safety	Eye protection required; immediate stop if jam
Power Supply	24 V battery (sold separately)

Frequently Asked Questions - GD24CS GREENWORKS

How to install the battery on the Greenworks GD24CS saw?

Align the lifting tabs of the battery pack with the grooves in the compartment, then push until an audible click. To remove, press the release button without releasing it and pull out.

How to adjust the cutting angle?

Loosen the angle locking knob, adjust the angle using the angle scale, then tighten the knob.

What is the maximum cutting depth of the GD24CS?

At 0° angle, the max depth is 63 mm; at 45°, it is 43 mm.

How to change the saw blade?

First remove the battery. Use the lower guard lever to lift the guard. Press the spindle lock button, then use the hex key to loosen the bolt. Remove the bolt, outer flange, and blade. To install, follow the reverse, making sure the blade arrow points in the same direction as the upper guard arrow.

Which battery to use with the GD24CS?

Use a 24 V battery from the G24B2/G2, 4B4 or other compatible BAG series.

How to avoid kickbacks?

Maintain the correct cutting depth, check for nails, use sharp blades, support the workpiece, do not force the cut, and hold the saw firmly with both hands.

How to clean the circular saw?

Remove the battery. Clean the housing with a soft damp cloth. Use a vacuum to clear the vents. Do not use solvents or harsh detergents.

What to do if the blade jams during cutting?

Immediately release the trigger to avoid a kickback. Let the blade stop completely before removing the saw.

What is the weight of the saw without battery?

The weight without battery is 3.35 kg.

What is the warranty of the Greenworks GD24CS saw?

The warranty is 3 years on the product and 2 years on batteries for private use. It covers manufacturing defects. Wear parts are excluded.

User questions about GD24CS GREENWORKS

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

No questions yet. Be the first to ask one.

Download the instructions for your Saw in PDF format for free! Find your manual GD24CS - GREENWORKS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. GD24CS by GREENWORKS.

USER MANUAL GD24CS GREENWORKS

CRD401

Original Instructions / Übersetzung der Originalanweisungen / Traducción de las instrucciones originales / Traduzione delle istruzioni originali / Traduction des instructions d'origine / Traduzido a partir das instruções originais / Vertaling van de originele gebruiksaanwijzing / Перевод оригинальных инструкций / Alkuperäisten ohjeiden käännös / Översättning av originalinstruktionerna / Produsentens instruksjoner / Oversættelse af de originale vejledninger / Thumaczenie oryginalnej instrukcji / Překlad originálního návodu / Preklad originálneho návodu / Prevod originalnih navodil / Prijevod izvornih uputa / Az eredeti utasítás fordítása / Traducere a instructiunilor originale / Превод на оригиналните инструкции / Авθεντικές οδηγίες / ترجمة التعليمات الأصلية / Orijinal Talimatların Tercümesi / Originalių instrukciju vertimas / Instrukciju tulkojums no originalvalodas / Originaalkasutusjuhendi tõlge

English

1 Description......4

1.1 Purpose.... 4
1.2 Overview.... 4
1.3 Packing list.... 4

2 Safety...... 4

3 Installation.... 4

3.1 Unpack the machine.... 4
3.2 Install the battery pack....4
3.3 Remove the battery pack.... 4
3.4 Install the blade....4
3.5 Remove the blade.... 4

4 Operation.... 5

4.1 Start the machine.... 5
4.2 Stop the machine.... 5
4.3 Adjust the cutting angle....5
4.4 Adjust the cutting depth....5
4.5 Adjust the cutting width.... 5
4.6 Operate the machine.... 5

5 Maintenance....5

5.1 Clean the machine.... 5

6 Technical data....5

7 Warranty......6

8 EC Declaration of conformity......6

1 DESCRIPTION

1.1 PURPOSE

The machine is used to cut all types of wood.

1.2 OVERVIEW

Figure 1.

1	Switch trigger	7	Edge guide
2	Lock-off Button	8	Width adjustment knob
3	Spindle lock button
4	Hex key	9	Lower guard
5	Depth adjustment lever	10	Base
5	Depth adjustment lever	11	Lower guard lever
6	Bevel adjustment knob	12	Tube

1.3 PACKING LIST

1 Circular saw
2 Hex key
3 Cutting blade
4 Edge guide
5 Dust tube with a screw

6 Manual ( operation manual, safety instruction manual, figure sheet )

2 SAFETY

WARNING

Make sure that you do/obey all safety instructions.

Refer to Safety Manual.

3 INSTALLATION

3.1 UNPACK THE MACHINE

WARNING

Make sure that you correctly assemble the machine before use.

WARNING

If parts of the machine are damaged, do not use the machine.
If you do not have all the parts, do not operate the machine.
If the parts are damaged or missing, contact the service center.
Open the package.
Read the documentation in the box.
Remove all the unassembled parts from the box.
Remove the machine from the box.
Discard the box and package in compliance with local regulations.

3.2 INSTALL THE BATTERY PACK

Figure 2.

▲ WARNING

If the battery pack or charger is damaged, replace the battery pack or the charger.
Stop the machine and wait until the motor stops before you install or remove the battery pack.
Read, know, and do the instructions in the battery and charger manual.
Align the lift ribs on the battery pack with the grooves in the battery compartment.
Push the battery pack into the battery compartment until the battery pack locks into place.
When you hear a click, the battery pack is installed.

3.3 REMOVE THE BATTERY PACK

Figure 2.

Push and hold the battery release button.
Remove the battery pack from the machine.

3.4 INSTALL THE BLADE

Figure 3.

NOTE

Before you install the blade, remove the battery pack from the machine.

Use the lower guard lever to lift the lower guard and hold the lever.
Install the new blade.
Put the outer flange and the blade bolt on the spindle.
Push the spindle lock button to lock the spindle.
Use the hex key to tighten the bolt clockwise.

NOTE

The arrow on the blade points the same direction as the arrow on the top guard.

3.5 REMOVE THE BLADE

Figure 4.

i NOTE

Before you remove the blade, remove the battery pack.

Push the spindle lock button to lock the spindle.
Use the hex key to loosen the blade bolt counterclockwise.

English

Remove the bolt and outer flange.
Use the lower guard lever to lift the lower guard and hold the lever.
Remove the blade.

4 OPERATION

WARNING

Always wear eye protection.

WARNING

Do not use any attachments or accessories not recommended by the manufacturer of this product.

4.1 START THE MACHINE

Figure 5

i NOTE

The machine can not work until the lock-off Button is pushed fully to the left or right. Do not operate the machine at low speeds for extended periods of time.

Pull the trigger to turn the machine ON.

4.2 STOP THE MACHINE

Figure 5.

Release the trigger to stop the machine.

4.3 ADJUST THE CUTTING ANGLE

Figure 6.

Loosen the bevel lock knob.
Use bevel scale to set the necessary angle.
Tighten the bevel lock knob.

4.4 ADJUST THE CUTTING DEPTH

Figure 7.

Loosen the depth adjustment lever.
Raise or lower the base until the depth scale reaches the required cutting depth.
Tighten the depth adjustment lever.

4.5 ADJUST THE CUTTING WIDTH

Figure 8.

Loosen the width adjustment knob to move the edge guide to the necessary width.
Tighten the width adjustment knob after adjustment.

Kickback occurs when the blade stalls quickly and the machine is driven back to you. A step which pinches the blade in the wood can cuase blade stalling.

WARNING

To prevent kickback, release switch trigger immediately if the blade stalls.

Keep the blade at the correct depth position.
Examine the workpiece for nails before you cut. Do not saw into a nail.
Make straight cuts. Use a straight edge guide when rip cutting. This helps prevent you twist the blade.
Use clean, sharp, and correctly set blades. Do not make cuts with blunt blades.
Support the workpiece correctly before you begin a cut.
Use stable pressure when you make a cut. Do not force a cut.
Do not cut warped or wet lumber.
Hold the saw tightly with the two hands and keep your body in a balanced position to against the forces if kickback occurs.

5 MAINTENANCE

CAUTION

Do not let brake fluids, gasoline, petroleum-based materials touch the plastic parts. Chemicals can cause damage to the plastic, and make the plastic unserviceable.

CAUTION

Do not use strong solvents or detergents on the plastic housing or components.

WARNING

Remove the battery pack from the machine before maintenance.

5.1 CLEAN THE MACHINE

CAUTION

The machine must be dry. Humidity can cause risks of electrical shocks.

Clear the unwanted material out of the air vent with a vacuum cleaner.
Do not spray the air vent or put the air vent in solvents.
Clean the housing and the plastic components with a moist and soft cloth.

6 TECHNICAL DATA

Voltage 24 V

No Load Speed 4,500 min	-1
Blade diameter 184 mm
Weight without battery 3.35 kg
Max cutting depth at 0° 63 mm
Max cutting depth at 45° 43 mm
Battery model G24B2/G24B4	and other BAG series
Charger model 2913907 and other CAG series
Measured sound pressure level	84.6dB(A), K_pA = 3 dB(A)
Measured sound power level	95.6 dB(A), K_wA = 3 dB(A)
Vibration < 2.5 m/s	² , K = 1.5 m/s ²

The recommended ambient temperature range:

Item Temperature
Appliance storage temperature range	32°F (0°C) - 113°F (45°C)
Appliance operation temperature range	32°F (0°C) - 113°F (45°C)
Battery charging temperature range	39°F (4°C) - 104°F (40°C)
Charger operation temperature range	39°F (4°C) - 104°F (40°C)
Battery storage temperature range	32°F (0°C) - 113°F (45°C)
Battery discharging temperature range	32°F (0°C) - 113°F (45°C)

7 WARRANTY

(The full warranty terms and conditions can be found on Greenworks webpage)

The Greenworks warranty is 3 years on the product, and 2 years on batteries (consumer/private usage) from the date of purchase. This warranty covers manufacturing faults. A faulty product under warranty might be either repaired or replaced. A unit that has been misused or used in other ways then described in the owner's manual might be rejected for warranty. Normal wear, and wear parts are not considered as warranty. The original manufacturer warranty is not affected by any additional warranty offered by a dealer or retailer.

A faulty product must be returned to the point of purchase in order to claim for warranty, together with the proof of purchase (receipt).

8 EC DECLARATION OF CONFORMITY

Name and address of the manufacturer:

Name: GLOBGRO AB

Globe Group Europe

Address: Riggaregatan 53, 211 13 Malmö, Sweden

Name and address of the person authorised to compile the technical file:

Name: Peter Söderström

Address: Riggaregatan 53, 211 13 Malmö, Sweden

Herewith we declare that the product

Category: Circular saw

Model: CRD401

Serial number: See product rating label

Year of Construction: See product rating label

- is in conformity with the relevant provisions of the Machinery Directive 2006/42/EC.

- is in conformity with the provisions of the following other EC-Directives:

• 2011/65/EU & (EU)2015/863

2014/30/EU

Furthermore, we declare that the following parts, clauses of European harmonised standards have been used:

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Place, date: Malmö, 02.02.2020

Signature: Ted Qu, Quality Director

Ted Qu

Deutsch

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Luogo, data: Malmö, 02.02.2020

8 DÉCLARATION DE CONFORMITÉ CE

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Français

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Local, data: Malmö, 02.02.2020

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

- EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Ort, datum: Malmö, 02.02.2020

Signatur: Ted Qu, Kvalitetschef

Ted Qu

Norsk

1 Beskrivelse.... 50

1.1 Formål....50
1.2 Oversikt.... 50
1.3 Pakkeliste....50

2 Sikkerhet.... 50

3.4 SETT PÅ KNIVBLADET

Figur 3.

i MERK

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Sted, dato: Malmö, 02.02.2020

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Sted, dato: Malmö, 02.02.2020

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Místo, datum: Malmö, 02.02.2020

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Miesto, dátum: Malmö, 02.02.2020

Podpis: Ted Qu, riaditel' pre kvalitu

Ted Qu

Slovenščina

1 Opis....71

1.1 Namen....71
1.2 Pregled....71
1.3 Seznam delov....71

2 Varnost.... 71

3 Namestitev....71

3.1 Razpakiranje naprave.... 71
3.2 Namestitev akumulatorja....71
3.3 Odstranite akumulator.... 71
3.4 Nameščanje rezila....71
3.5 Odstranite rezilo.... 71

4 Delovanje....72

4.1 Zagon naprave.... 72
4.2 Zaustavitev naprave....72
4.3 Nastavitev kota rezanja....72
4.4 Nastavitev globine rezanja....72
4.5 Prilagoditev širine košnje.... 72
4.6 Upravljanje orodja.... 72

- EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Mjesto, datum Malmö, 02.02.2020

Potpis: Ted Qu, direktor za kvalitetu

Ted Qu

Magyar

1 Leírás....79

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Hely, dátum: Malmö, 02.02.2020

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Locul, data: Malmö, 02.02.2020

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

98.... retirement membership巴黎

IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC

62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

- EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Yer, tarih: Malmö, 02.02.2020

.הכלההוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָה

EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Luogo, data: Malmö, 02.02.2020

4.2 MAŠINAS APTURŠANA

Attels Nr. 5.

4.6 DARBMAŠINAS LIETOŠANA

Attēls Nr. 9.

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8

Vieta, datums: Malmö, 02.02.2020

• EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2; IEC 62321-3-1; IEC 62321-4; IEC 62321-5; IEC 62321-6; IEC 62321-7-1; IEC 62321-7-2; IEC 62321-8