WX390.31 - Drill WORX - Free user manual and instructions

Frequently Asked Questions - WX390.31 WORX

USER MANUAL WX390.31 WORX

Original instructions EN

1. DUST PROTECTION CAP
2. TOOL HOLDER LOCKING SLEEVE
3. FORWARD AND REVERSE ROTATION CONTROL
4. ON/OFF SWITCH
5. BATTERY PACK*
6. HAMMER DRILL /DRILL SELECTOR DIAL
7. BATTERY PACK RELEASE CLIP
8. LED LIGHT
9. SDS KEYLESS CHUCK ADAPTOR*
10. PH2 SCREWDRIVER BIT*
11. HSS METAL DRILL BIT (5mm,6mm)*

12. SDS PLUS DRILL BITS (6mm,8mm)*

13. Not all the accessories illustrated or described are included in standard delivery.

TECHNICAL DATA

Type WX390 WX390.1 WX390.31 WX390.9(3- designation of machinery, representative of Hammer Drill)

		WX390 WX390.1 Wx390.31		WX390.9
Voltage 20V Max**		---
No load speed 0-900/min
Impact rate 0-5000bpm
Impact energy 1.2J
Battery capacity		2.0Ah Li-lon 3.0Ah	i-lon 2.0Ah Li-lon
Max. drilling capacity	Steel	10mm
	Wood	13mm
	Concrete	13mm
	Brickwork	13mm
Machine weight 1.6kg				1.2kg

**Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts.

NOISE INFORMATION

A weighted sound pressure L	pA: 84dB(A)
A weighted sound power	LWA: 95dB(A)
KpA & KwA	3.0dB(A)
Wear ear protection when sound pressure is over	80dB(A)

VIBRATION INFORMATION

Vibration total values (triax vector sum) determined according to EN 60745:
Hammer drilling into concrete	Vibration emission value ah,HD=8.51m/s2
	Uncertainty K=1.5m/s2

The declared vibration total value may be used for comparing one tool with another, and may also be used in a preliminary assessment of exposure.

WARNING: The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used dependant on following examples and other variations on how the tool is used:

How the tool is used and the materials being cut or drilled.

The tool being in good condition and well maintained.

The use the correct accessory for the tool and ensuring it is sharp and in good condition.

The tightness of the grip on the handles and if any anti vibration accessories are used.

And the tool is being used as intended by its design and these instructions.

This tool may cause hand-arm vibration syndrome if its use is not adequately managed.

WARNING: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when

the tool is switched off and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period.

Helping to minimize your vibration exposure risk.

ALWAYS use sharp chisels, drills and blades.

Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate).

If the tool is to be used regularly then invest in anti vibration accessories.

Avoid using tools in temperatures of 10^ or less.

Plan your work schedule to spread any high vibration tool use across a number of days.

ACCESSIONS

	WX390 Wx390.1 WX390.31 WX390.9
Battery charger	1			/
Battery pack	1 2 1 /
Keyless chuck with adaptor	1
HSS drill bits 2 (5mm,6mm)
Screwdriver bits	4(PH2*50mm,PZ1*50mm,PZ2*50mm, Slotted*5.5mm*50mm)
SDS drill bits	2 (6mm,8mm)

We recommend that you purchase your accessories from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.

HAMMER SAFETY WARNINGS

1. Wear ear protectors. Exposure to noise can cause hearing loss.
2. Use auxiliary handles, If supplied with the tool. Loss of control can cause personal injury.
3. Hold power tools by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a 'live' wire may make exposed metal parts of the power tool 'live' and could give the operator an electric shock.

SAFETY WARNINGS FOR BATTERY PACK

a) Do not dismantle, open or shred cells or battery pack.
b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by conductive materials. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
c) Do not expose battery pack to heat or fire. Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
f) Seek medical advice immediately if a cell or battery pack has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with

a clean dry cloth if they become dirty.

i) Battery pack needs to be charged before use. Always refer to this instruction and use the correct charging procedure.
j) Do not maintain battery pack on charge when not in use.
k) After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance.
I) Battery pack gives its best performance when it is operated at normal room temperature (20^ ± 5^) .
m) When disposing of battery packs, keep battery packs of different electrochemical systems separate from each other.
n) Recharge only with the charger specified by WORK. Do not use any charger other than that specifically provided for use with the equipment. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
o) Do not use any battery pack which is not designed for use with the equipment.
p) Keep battery pack out of the reach of children.
q) Retain the original product literature for future reference.
r) Remove the battery from the equipment when not in use.
s) Disposc of properly.

SYMBOLS

10	To reduce the risk of injury, user must read instruction manual	Concrete
	Warning	Brickwork
	Wear ear protection	High speed
	Wear eye protection	Low speed
	Wear dust mask	Tool holder
	Do not expose to rain or water
	Do not burn
	Do not dispose of batteries.	Make sure the battery is removed prior to changing accessories.
	Return exhausted batteries to your local collection or recycling point	Drilling without impact
	Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.	Hammer Drilling
		Screwdriving
	Wear protective gloves
	Wood
	Steel

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the instruction book carefully.

INTENDED USE

The machine is intended for hammer drilling in concrete, brick and stone. It is also suitable for drilling without impact in wood, metal, ceramic and plastic. Machines with electronic control and right/left rotation are also suitable for screwdriving.

OPERATION

ACTION FIGURE
Removing The Battery	See Fig. A1
Inserting The Battery See Fig.	A2
Selecting The Operating Mode	See Fig. B
HAMMER DRILLING
Inserting Drill Bits See Fig. C1
Removing Drill Bits See Fig. C2
DRILLING & SCREWDRIVING
Inserting Adaptors See Fig. D1
Inserting Bits into Chuck See Fig. D2
Removing Adaptors See Fig. D3
Removing Bits from Chuck See Fig. D4
On/Off Switch See Fig. E
Switch Lock NOTE: The SwitchTrigger Can Be Locked In The Off Position.	See Fig. F
Forward Rotation Control	See Fig. G
Reverse Rotation Control	See Fig. H
LED Light	See Fig. I
Temperature Dependent Overload Protection	/
Protection Against Deep Discharging	/

WORKING HINTS FOR YOUR TOOL

If your power tool becomes over heated, set the speed to maximum and run no load for 2-3 minutes to cool the motor. SDS-plus tungsten carbide drill bits should always be used for concrete and masonry.

When drilling in metal, only use HSS drill bits in good condition. Where possible use a pilot hole before drilling a large diameter hole.

PROBLEM SOLUTION

1. REASONS FOR DIFFERENT BATTERY PACK WORKING TIMES

Charging time problems, having not used a battery pack for a prolonged time will reduce the battery pack working time. This can be corrected after several charge and discharge operations by charging & working with your tool. Heavy working conditions such as large screws into hard wood will use up the battery pack energy faster than lighter working conditions. Do not re-charge your battery pack below 0^ and above 30^ as this will affect performance.

MAINTENANCE

Remove the battery pack from the tool before carrying out any adjustment, servicing or maintenance.

Your power tool requires no additional lubrication or maintenance, except for the cleaning & lubrication of the SDS bits and adaptors before inserting into the chuck. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.

ENVIRONMENTAL PROTECTION

Waste electrical products must not be disposed of with household waste.

Please recycle where facilities exist.

Check with your local authorities or retailer for recycling advice.

DISPOSAL OF AN EXHAUSTED BATTERY PACK

To preserve natural resources, please recycle or dispose of the battery pack

Li-ion properly. This battery pack contains Li-ion batteries. Consult your local waste authority for information regarding available recycling and/or disposal options. Discharge your battery pack by operating your tool, then remove the battery pack from the tool housing and cover the battery pack connections with heavy-duty adhesive tape to prevent short circuit and energy discharge. Do not attempt to open or remove any of the components.

DECLARATION OF CONFORMITY

We,

POSITEC Germany GmbH

Declare that the product,

Description WORX Cordless Rotary Hammer

Type WX390 WX390.1 WX390.31

WX390.9 (3- designation of machinery, representative of Hammer Drill)

Function Hammering various materials

Complies with the following directives,

2006/42/EC

2011/65/EU

2014/30/EU

Standards conform to

EN 55014-1

EN 55014-2

EN 60745-1

EN 60745-2-6

The person authorized to compile the technical file,

Name Russell Nicholson

Address Positec Power Tools (Europe)

Ltd, PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Deputy Chief Engineer, Testing & Certification

Model WX390 WX390.1 WX390.31 WX390.9 (3- designations des pieces, illustration de la Perceuse percussion)

INFORMATIONS RELATIVES AU BRUIT

INFORMATIONS RELATIVES AUX VIBRATIONS

Modèle WX390 WX390.1 WX390.31

Ltd, PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Modelo WX390WX390.1WX390.31

(Europe) Ltd, PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Typ WX390 WX390.1 WX390.31

PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Tip WX390 WX390.1 WX390.31 WX390.9(3- denumire masina, reprezentand Ciocanul perforator)

		WX390 WX390.1 WX390.31		WX390.9
Tensiune nominalã 20V Max**		---
Turapie nominalã fãrã sarcinã 0-900/min
Numãr lovituri 0-5000bpm
Energie lovituri 1.2J
Capacitatea bateriei		2.0Ah Li-lon 3.0Ah Li-lon 2.0Ah Li-lon
Capacitate max. tãiere	Oțel	10mm
	Lemn	13mm
	Beton	13mm
	Zidărie	13mm
Greunate ma°inã		1.6kg		1.2kg

SOLUTIONI LA PROBLEM

1. MOTIVE PENTRU TIMPI DE LUCRU DIFERITI AI ACUMULATORULUI

Tip WX390 WX390.1 WX390.31

WX390.9(3- denumire maşina,

(representand Ciocanul perforator)

Ltd, PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Adjunct Inginer sef, Testare si certificare

1. PROTIPRACHOVÉ VÍČKO
2. ZAJISTOVACI POUZDRO DRŽAKU NASTROJE
3. OVLADÁNÍ OTÁČEK DOPřEDU A DOZADU
4. VYPÍNAC
5. BATERIE*
6. VOLIC REŽIMU VRTÁNÍ/PRÍKLEPOVÉ VRTÁNÍ
7. UVOLNOVACI TLACITKO BATERIE
8. SVETLO LED
9. ADAPTER RYCHLOUPINACIHO SKLICIDLA SDS*
10. SROUBOVACI NASTAVEC PH2*
11. VRTÁK HSS DO KOVU (5mm,6mm)*

12. VRTÁKY SDS (6mm,8mm)*

13. Standardni dodávka nemusi obsahovat veškeré vyobrazené ā popsané príslušenstvi.

TECHNICKE UDAJE

Typ WX390 WX390.1 WX390.31 WX390.9(3- označeni stroje, zastupce Priklepopá vrtačka)

Ltd, PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Typ WX390 WX390.1 WX390.31 WX390.9

(3 - označenie zariadenia, zastupca Vrtacie kladivo)

Ltd, PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Cumpre as seguintes Directivas, 2006/42/EC 2011/65/EU 2014/30/EU

	WX390 WDX390.1 WX390.31 WX390.9
laddning	1			/
Batteripaket	1 2 1 /
Snabbchuck med adapter	1
HSS -borrbits 2 (5mm,6mm)
skruvmejselbits	4(PH2*50mm,PZ1*50mm,PZ2*50mm, Slitsade*5.5mm*50mm)
SDS -borrbits	2 (6mm,8mm)

Typ WX390 WX390.1 WX390.9

WX390.31(3- beteckning for maskin, representant for hammarborr)

Funktion Slagboring i oika material

Uppfyller foljande direktiv,

2006/42/EC

2011/65/EU

2014/30/EU

Standarder overensstammer med

EN 55014-1

EN 55014-2

EN 60745-1

EN 60745-2-6

Ltd, PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Vrsta izdelka WX390 WX390.1 WX390.31

WX390.9(3-zasnova naprave, predstavnik udarnih vrtalnikov)

Ime: Russell Nicholson

Naslov: Positec Power Tools (Europe)

Ltd, PO Box 6242, Newbury, RG14 9LT, UK

Suzhou 2016/06/12

Allen Ding

Pooblasceni glavni inzenir za testiranje in certificiranje

WORX

you've got the power

www.worx.com

Copyright © 2015, Positec. All Rights Reserved.

AR01005701