Q: How to set the WORX WX121 drill for drilling aluminum?

Operating mode: Use the standard drilling mode (mode 2), without activating the hammer function. The hammer function is not suitable for aluminum. Torque setting: Set the torque ring to a position between 14 and 20 . These positions are specifically designed for hard materials like aluminum. Rotation speed: Set to the low range (0-450 rpm). This prevents overheating and maintains drilling quality in aluminum. Type and size of drill bit: Use standard metal drill bits with a diameter of 1.5 to 13 mm . Your WX121 accepts chucks up to 10 mm. For aluminum, prefer high-speed steel or carbide bits for better longevity. Practical tip: Progress gradually without forcing. Apply steady and consistent pressure for clean drilling without damaging the material.

Q: How to change the drill bit on a WORX WX318 drill?

Your WORX WX318 drill is equipped with a keyless chuck that can accept drill bits up to 13 mm in diameter. Changing the drill bit is a simple operation that requires no additional tools. Before you begin: Always unplug the drill from the wall socket before proceeding to change the drill bit. This step is imperative for your safety. To remove the old drill bit: Hold the drill firmly with one hand. With the other hand, grasp the chuck (the front part that holds the drill bit) and turn it counterclockwise until it opens completely. The drill bit will come out easily. If the drill bit is stuck, you can use the reverse rotation function of your WX318: set the selector to reverse, briefly press the trigger to rotate the chuck in the opposite direction, then return to normal mode. To insert the new drill bit: Ensure that the drill bit does not exceed 13 mm in diameter. Insert the drill bit into the chuck, making sure it is centered properly. Ensure that the pointed end of the drill bit is facing forward. To tighten the chuck: Always hold the body of the drill firmly with one hand. With the other hand, grasp the chuck and turn it clockwise until it is securely tightened. Do not use excessive force: the chuck only needs to be tight enough to hold the drill bit in place. Check that the drill bit does not move by trying to pull it slightly. Once the drill bit is correctly installed and tightened, plug the drill back in and you are ready to use it. To switch from simple drilling to hammering (or vice versa), use the hammer/drill selector located on the body of the tool.

Question 1

How to set the WORX WX121 drill for drilling aluminum?

Accepted Answer

Operating mode: Use the standard drilling mode (mode 2), without activating the hammer function. The hammer function is not suitable for aluminum.

Torque setting: Set the torque ring to a position between 14 and 20. These positions are specifically designed for hard materials like aluminum.

Rotation speed: Set to the low range (0-450 rpm). This prevents overheating and maintains drilling quality in aluminum.

Type and size of drill bit: Use standard metal drill bits with a diameter of 1.5 to 13 mm. Your WX121 accepts chucks up to 10 mm. For aluminum, prefer high-speed steel or carbide bits for better longevity.

Practical tip: Progress gradually without forcing. Apply steady and consistent pressure for clean drilling without damaging the material.

Question 2

How to set the WORX WX121 drill to drill drywall?

Accepted Answer

To drill drywall with your WORX WX121 drill, you first need to select the hammer mode (percussion drilling) using the mode selector provided on the tool. This mode is specifically designed for work on masonry and similar materials like drywall.

Next, use the speed adjustment ring to set the speed: for drywall, a medium to low speed (around 0-900 RPM) is recommended to avoid damaging the material. The drill offers a range of 0-1700 RPM, giving you good flexibility.

Important: the maximum drilling diameter in masonry is 8 mm according to the specifications of this tool. Make sure to use a suitable bit for the desired diameter, compatible with the 10 mm chuck. Wear safety glasses and hold the tool firmly while drilling.

Question 3

How do I turn off the built-in LED light on the WORX WX175.9 drill?

Accepted Answer

The WORX WX175.9 drill is equipped with a built-in LED light that automatically turns on when you press the power switch.

To turn off this light, there is no specific button. In fact, the LED turns off automatically about 20 seconds after you release the switch. Therefore, you do not need to take any additional action to turn off the light.

In summary:

The LED light turns on when you hold the switch down.
It turns off automatically 20 seconds after you release the switch.
No manual control to turn off the light is necessary.

Question 4

How to change the drill bit on a WORX WX318 drill?

Accepted Answer

Your WORX WX318 drill is equipped with a keyless chuck that can accept drill bits up to 13 mm in diameter. Changing the drill bit is a simple operation that requires no additional tools.

Before you begin: Always unplug the drill from the wall socket before proceeding to change the drill bit. This step is imperative for your safety.

To remove the old drill bit: Hold the drill firmly with one hand. With the other hand, grasp the chuck (the front part that holds the drill bit) and turn it counterclockwise until it opens completely. The drill bit will come out easily. If the drill bit is stuck, you can use the reverse rotation function of your WX318: set the selector to reverse, briefly press the trigger to rotate the chuck in the opposite direction, then return to normal mode.

To insert the new drill bit: Ensure that the drill bit does not exceed 13 mm in diameter. Insert the drill bit into the chuck, making sure it is centered properly. Ensure that the pointed end of the drill bit is facing forward.

To tighten the chuck: Always hold the body of the drill firmly with one hand. With the other hand, grasp the chuck and turn it clockwise until it is securely tightened. Do not use excessive force: the chuck only needs to be tight enough to hold the drill bit in place. Check that the drill bit does not move by trying to pull it slightly.

Once the drill bit is correctly installed and tightened, plug the drill back in and you are ready to use it. To switch from simple drilling to hammering (or vice versa), use the hammer/drill selector located on the body of the tool.

User manual WORX Drill : user manuals and guides in PDF

Models WORX Drill most viewed

Other categories WORX

Recent questions about Drill WORX