Q: What is the exact cutting height at position 5 on the WORX WG743E mower?

The WORX WG743E offers 7 height adjustment positions ranging from 20 mm to 80 mm . The adjustment is made progressively across the entire available range. However, the technical manual does not specify the exact values in millimeters for each individual position (including position 5). The 7 positions are evenly distributed across the 20-80 mm range, suggesting a step of about 10 mm between each position. For reference, position 5 would therefore be around 60 mm , but this value is not officially confirmed by WORX in the provided documentation. To know the precise height of position 5, please refer to the adjustment diagram illustrated (Fig. I) in your paper manual, or contact WORX customer service directly, who can provide you with this detailed technical information.

Q: What is the recommended sharpening frequency for the blade of the WORX WG743E mower?

According to the documentation for the WORX WG743E, sharpening the blade twice per mowing season is generally sufficient under normal conditions. However, if your lawn has sandy or rocky soil, more frequent sharpening may be necessary as sand wears down the sharp edges more quickly. Blade Replacement The blade should be replaced after 50 hours of mowing or every 2 years , whichever comes first. Immediately replace any bent or damaged blade. Key Points for Sharpening Maintain the balance of the blade Respect the original cutting angle Sharpen both ends by removing equal amounts of material Keep the blade sharp for better mowing performance

Q: How to disassemble and reassemble the cutting head of the WORX WG186E.92?

To disassemble the cutting head: First, remove the battery Use the provided hex key to unlock the cutting head Remove the empty spool from its housing To reassemble with new line: Use a line with a diameter of 2.4 mm (available length: 4 m) Wrap the line following the clockwise direction Leave about 19 cm of line extending on each side Replace the spool and lock the head with the hex key Note: The hex key and the cutting head manipulation key are provided with the device.

Q: What should I do if the boundary wire is missing with my Landroid WG799E?

The Landroid WG799E uses a boundary wire which is an essential element for defining the mowing area of the robotic mower. If the wire is missing, here’s what you need to know: Role of the boundary wire This wire creates a virtual barrier that indicates to the robot the limits of the area to be mowed. Without this wire, the robot cannot function properly. Installing the wire During installation, the wire must be: Secured with the provided metal pegs At least 35 cm away from the edge of the lawn (use the provided distance gauge) Initially anchored to the grass before being buried permanently If another Landroid robot is nearby, leave a space of at least 0.5 m between the wire and the neighboring property Extending the wire The wire can be extended by splicing the ends together and securing the joint with appropriate adhesive. If your wire is damaged or truly missing, contact WORX support or an authorized dealer to obtain an original replacement wire to ensure compatibility and safety of your device.

Q: How to change or modify the PIN code of the Landroid L1000?

According to the Landroid L1000 manual, the PIN code is set during the first startup of the mower: you choose a four-digit PIN code at that moment. Regarding the modification of the PIN code after its creation , the Landroid L1000 manual does not provide a detailed procedure integrated into the mower's physical menu. However, it mentions that in case of an input error, you have the option to reset your PIN . Two recommended approaches: Check the WORX mobile app - It is usually in the app (WiFi compatible on the L1000) that the security settings and the option to modify the PIN can be found. If you can't find it in the app , you can reset the PIN via the mower itself during the next

Q: How to set the WORX WX121 drill for drilling aluminum?

Operating mode: Use the standard drilling mode (mode 2), without activating the hammer function. The hammer function is not suitable for aluminum. Torque setting: Set the torque ring to a position between 14 and 20 . These positions are specifically designed for hard materials like aluminum. Rotation speed: Set to the low range (0-450 rpm). This prevents overheating and maintains drilling quality in aluminum. Type and size of drill bit: Use standard metal drill bits with a diameter of 1.5 to 13 mm . Your WX121 accepts chucks up to 10 mm. For aluminum, prefer high-speed steel or carbide bits for better longevity. Practical tip: Progress gradually without forcing. Apply steady and consistent pressure for clean drilling without damaging the material.

Question 1

What does the yellow LED mean that lights up when I connect the battery to my WORX WG325E saw?

Accepted Answer

The manual for the WORX WG325E does not document the LED indicators of the product itself. However, the yellow (or orange) LED that you see lighting up when connecting the battery comes from the recommended WA3880 charger or the battery itself, not from the saw.

If you are using the WA3880 charger: The LED indicators of this charger mean:

Flashing green LED: the battery is charging (this state lasts about 1 to 2 hours depending on capacity)
Solid green LED (no flashing): the battery is fully charged and charging is complete
Flashing red LED: the battery is too hot or too cold. The charger automatically activates a protection circuit and suspends charging until the battery reaches the correct temperature. Let it cool down or warm up before trying again

An orange or yellow LED may be perceived as flashing red if you see it partially or under certain lighting angles. If you see an unusual color, refer to the LED indicator guide that may be printed under the charger.

Important: Only charge your WA3551 or WA3639 battery with the specifically recommended WA3880 charger. Do not use other chargers, as WORX 20V Li-ion batteries are designed to work in synergy with this charger. If your battery refuses to charge or shows a persistent problem, contact WORX customer service or the retailer.

Question 2

What is the exact cutting height at position 5 on the WORX WG743E mower?

Accepted Answer

The WORX WG743E offers 7 height adjustment positions ranging from 20 mm to 80 mm. The adjustment is made progressively across the entire available range.

However, the technical manual does not specify the exact values in millimeters for each individual position (including position 5). The 7 positions are evenly distributed across the 20-80 mm range, suggesting a step of about 10 mm between each position. For reference, position 5 would therefore be around 60 mm, but this value is not officially confirmed by WORX in the provided documentation.

To know the precise height of position 5, please refer to the adjustment diagram illustrated (Fig. I) in your paper manual, or contact WORX customer service directly, who can provide you with this detailed technical information.

Question 3

What is the recommended sharpening frequency for the blade of the WORX WG743E mower?

Accepted Answer

According to the documentation for the WORX WG743E, sharpening the blade twice per mowing season is generally sufficient under normal conditions.

However, if your lawn has sandy or rocky soil, more frequent sharpening may be necessary as sand wears down the sharp edges more quickly.

Blade Replacement

The blade should be replaced after 50 hours of mowing or every 2 years, whichever comes first. Immediately replace any bent or damaged blade.

Key Points for Sharpening

Maintain the balance of the blade
Respect the original cutting angle
Sharpen both ends by removing equal amounts of material
Keep the blade sharp for better mowing performance

Question 4

How to disassemble and reassemble the cutting head of the WORX WG186E.92?

Accepted Answer

To disassemble the cutting head:

First, remove the battery
Use the provided hex key to unlock the cutting head
Remove the empty spool from its housing

To reassemble with new line:

Use a line with a diameter of 2.4 mm (available length: 4 m)
Wrap the line following the clockwise direction
Leave about 19 cm of line extending on each side
Replace the spool and lock the head with the hex key

Note: The hex key and the cutting head manipulation key are provided with the device.

Question 5

What should I do if the boundary wire is missing with my Landroid WG799E?

Accepted Answer

The Landroid WG799E uses a boundary wire which is an essential element for defining the mowing area of the robotic mower. If the wire is missing, here’s what you need to know:

Role of the boundary wire

This wire creates a virtual barrier that indicates to the robot the limits of the area to be mowed. Without this wire, the robot cannot function properly.

Installing the wire

During installation, the wire must be:

Secured with the provided metal pegs
At least 35 cm away from the edge of the lawn (use the provided distance gauge)
Initially anchored to the grass before being buried permanently
If another Landroid robot is nearby, leave a space of at least 0.5 m between the wire and the neighboring property

Extending the wire

The wire can be extended by splicing the ends together and securing the joint with appropriate adhesive.

If your wire is damaged or truly missing, contact WORX support or an authorized dealer to obtain an original replacement wire to ensure compatibility and safety of your device.

Question 6

How to charge the battery of the WORX WG929.1?

Accepted Answer

To charge the battery of your WORX WG929.1, use only the WA3742 charger provided with the device. The charger and the battery have been specifically designed to work together.

Charging Steps

Connect the WA3742 charger to a 120V~60Hz outlet
Insert the WA3525 (2.0Ah) battery into the charger
The charging indicator turns red during charging
Wait for the indicator to turn green to indicate that the battery is full

Charging Time

A full charge takes approximately 5 hours with the WA3742 charger.

Important Conditions

Charge only at an ambient temperature between 0°C and 40°C
Do not charge outside of this temperature range
Never insert metallic objects into the connectors of the charger or battery
Use only the WA3742 charger - any other charger may damage the battery

Tip: To extend the life of your battery, do not leave it charging indefinitely once it is full. Unplug the charger as soon as the indicator turns green.

Question 7

How to change or modify the PIN code of the Landroid L1000?

Accepted Answer

According to the Landroid L1000 manual, the PIN code is set during the first startup of the mower: you choose a four-digit PIN code at that moment.

Regarding the modification of the PIN code after its creation, the Landroid L1000 manual does not provide a detailed procedure integrated into the mower's physical menu. However, it mentions that in case of an input error, you have the option to reset your PIN.

Two recommended approaches:

Check the WORX mobile app - It is usually in the app (WiFi compatible on the L1000) that the security settings and the option to modify the PIN can be found.
If you can't find it in the app, you can reset the PIN via the mower itself during the next

Question 8

How to set the WORX WX121 drill for drilling aluminum?

Accepted Answer

Operating mode: Use the standard drilling mode (mode 2), without activating the hammer function. The hammer function is not suitable for aluminum.

Torque setting: Set the torque ring to a position between 14 and 20. These positions are specifically designed for hard materials like aluminum.

Rotation speed: Set to the low range (0-450 rpm). This prevents overheating and maintains drilling quality in aluminum.

Type and size of drill bit: Use standard metal drill bits with a diameter of 1.5 to 13 mm. Your WX121 accepts chucks up to 10 mm. For aluminum, prefer high-speed steel or carbide bits for better longevity.

Practical tip: Progress gradually without forcing. Apply steady and consistent pressure for clean drilling without damaging the material.

Question 9

How to set the WORX WX121 drill to drill drywall?

Accepted Answer

To drill drywall with your WORX WX121 drill, you first need to select the hammer mode (percussion drilling) using the mode selector provided on the tool. This mode is specifically designed for work on masonry and similar materials like drywall.

Next, use the speed adjustment ring to set the speed: for drywall, a medium to low speed (around 0-900 RPM) is recommended to avoid damaging the material. The drill offers a range of 0-1700 RPM, giving you good flexibility.

Important: the maximum drilling diameter in masonry is 8 mm according to the specifications of this tool. Make sure to use a suitable bit for the desired diameter, compatible with the 10 mm chuck. Wear safety glasses and hold the tool firmly while drilling.

Question 10

How to install the side discharge cover?

Accepted Answer

The side discharge cover is one of the essential parts of the initial assembly kit for your WORX WG751.3 mower. This part, included in the box, directs the cut grass to the side of the device.

Installation Procedure

Detailed installation instructions for the side discharge cover are provided in the ASSEMBLY & OPERATION section of your manual, in figures E1 and E2. These illustrations show step by step:

The exact location to attach the cover to the chassis
The correct orientation of the cover
The attachment and locking points

Before use, ensure that the cover is completely locked and securely attached. A poorly installed cover could detach during use.

Refer to figures E1 and E2 of the PDF manual above for precise visual details, or download the complete guide if you need further clarifications.

User manual WORX : user manuals and guides in PDF

Models WORX most viewed

Browse manuals WORX by appliance type

Recent questions about devices WORX