Q: How to disassemble and reassemble the cutting head of the WORX WG186E.92?

To disassemble the cutting head: First, remove the battery Use the provided hex key to unlock the cutting head Remove the empty spool from its housing To reassemble with new line: Use a line with a diameter of 2.4 mm (available length: 4 m) Wrap the line following the clockwise direction Leave about 19 cm of line extending on each side Replace the spool and lock the head with the hex key Note: The hex key and the cutting head manipulation key are provided with the device.

Question 1

How to disassemble and reassemble the cutting head of the WORX WG186E.92?

Accepted Answer

To disassemble the cutting head:

First, remove the battery
Use the provided hex key to unlock the cutting head
Remove the empty spool from its housing

To reassemble with new line:

Use a line with a diameter of 2.4 mm (available length: 4 m)
Wrap the line following the clockwise direction
Leave about 19 cm of line extending on each side
Replace the spool and lock the head with the hex key

Note: The hex key and the cutting head manipulation key are provided with the device.

Question 2

How to charge the battery of the WORX WG929.1?

Accepted Answer

To charge the battery of your WORX WG929.1, use only the WA3742 charger provided with the device. The charger and the battery have been specifically designed to work together.

Charging Steps

Connect the WA3742 charger to a 120V~60Hz outlet
Insert the WA3525 (2.0Ah) battery into the charger
The charging indicator turns red during charging
Wait for the indicator to turn green to indicate that the battery is full

Charging Time

A full charge takes approximately 5 hours with the WA3742 charger.

Important Conditions

Charge only at an ambient temperature between 0°C and 40°C
Do not charge outside of this temperature range
Never insert metallic objects into the connectors of the charger or battery
Use only the WA3742 charger - any other charger may damage the battery

Tip: To extend the life of your battery, do not leave it charging indefinitely once it is full. Unplug the charger as soon as the indicator turns green.

Question 3

How do I disassemble the WORX WG157E.9 trimmer to replace the cutting line?

Accepted Answer

To replace the cutting line on your WORX WG157E.9 trimmer, you first need to access the cutting head by following these steps. Safety first: unplug the device or remove the battery before proceeding.

Disassembly steps:

Remove the protective cap by pressing the release latch (see figures I1 and I2 in the manual). This cap protects access to the cutting head.
Remove the cover of the cutting head by pressing the release buttons located on each side of the cover (see figure J). The cover should detach easily.
Remove the spool of line from the cutting head. It usually comes off by pulling straight towards you after opening the cover.

Replacing the line: Remove the old line from the spool by completely unwinding it. Insert a new line with a diameter of exactly 1.65 mm - this is a critical dimension: lines of other diameters will not fit properly and will damage the cutting head. Manually wind the new line evenly and tightly onto the spool, following the guiding notches (see figures K1 to K4 in the manual). Ensure that the line is taut and securely fixed at the starting point on the spool.

Reassembly: Reinsert the filled spool into the cutting head by clicking it into place. Pass both ends of the line through the exit eyelets located on the cover. Replace the cover by snapping it firmly until you hear a safety click. Replace the protective cap and secure it.

Important points: Use only a compatible WORX line with a diameter of 1.65 mm to ensure optimal operation. If the line stretches too much during operation, unplug the device, remove the cover, and turn the spool counterclockwise to shorten it. Check that the line is properly wound and that no mesh is stuck before putting the device back into service.

Question 4

How to solve a line feed problem on the WORX WG168E.9 trimmer?

Accepted Answer

If you are experiencing a line feed problem with your WORX WG168E.9 trimmer, here are several steps to identify and resolve the issue:

1. Check the line

Make sure the line is not tangled or broken.
Remove any debris or obstruction that may be blocking the line.

2. Inspect the spool

Open the cutting head to access the spool.
Check that the line is properly wound and that there is enough line left.
If the line is too short or worn, replace it with a compatible line.

3. Check the automatic feed mechanism

Test if the automatic feed mechanism is working properly by gently tapping the cutting head on the ground (depending on the model).
If the line does not come out automatically, try pulling a bit of line manually.

4. Check the mounting of the cutting head

Ensure that the cutting head is securely attached and aligned.
An incorrect mounting can prevent the line from feeding properly.

5. Usage technique

Hold the trimmer at the angle recommended by the manufacturer.
Avoid pressing too hard on the cutting head, as this may block the line.

By following these tips, you should be able to resolve most line feed problems with your WORX WG168E.9 trimmer.

Question 5

Is there an instructional video to learn how to use the WORX WG160E trimmer?

Accepted Answer

Yes, there are several instructional videos available online that show how to effectively use the WORX WG160E trimmer. These videos provide practical demonstrations, safety tips, and advice on how to properly maintain your device.

Where to find these videos?

YouTube: By searching for "WORX WG160E trimmer tutorial" or "how to use WORX WG160E", you will find many videos made by users or by the brand itself.
Official WORX website: The manufacturer's website sometimes offers video guides and tutorials for its products.

Tips for using your WORX WG160E trimmer effectively

Make sure the battery is fully charged before use.
Always wear protective equipment (gloves, safety glasses).
Follow the assembly and starting instructions to avoid any damage.
Regularly clean the cutting head to maintain optimal performance.

These video resources will help you better understand the operation and maintenance of your WORX WG160E trimmer.

User manual WORX Grass trimmer : user manuals and guides in PDF

Models WORX Grass trimmer most viewed

Other categories WORX

Recent questions about Grass trimmer WORX