Q: What is the exact cutting height at position 5 on the WORX WG743E mower?

The WORX WG743E offers 7 height adjustment positions ranging from 20 mm to 80 mm . The adjustment is made progressively across the entire available range. However, the technical manual does not specify the exact values in millimeters for each individual position (including position 5). The 7 positions are evenly distributed across the 20-80 mm range, suggesting a step of about 10 mm between each position. For reference, position 5 would therefore be around 60 mm , but this value is not officially confirmed by WORX in the provided documentation. To know the precise height of position 5, please refer to the adjustment diagram illustrated (Fig. I) in your paper manual, or contact WORX customer service directly, who can provide you with this detailed technical information.

Q: What is the recommended sharpening frequency for the blade of the WORX WG743E mower?

According to the documentation for the WORX WG743E, sharpening the blade twice per mowing season is generally sufficient under normal conditions. However, if your lawn has sandy or rocky soil, more frequent sharpening may be necessary as sand wears down the sharp edges more quickly. Blade Replacement The blade should be replaced after 50 hours of mowing or every 2 years , whichever comes first. Immediately replace any bent or damaged blade. Key Points for Sharpening Maintain the balance of the blade Respect the original cutting angle Sharpen both ends by removing equal amounts of material Keep the blade sharp for better mowing performance

Question 1

How to replace the front wheels of the WORX Landlord WG798E?

Accepted Answer

The manual for the WORX Landlord WG798E does not provide a detailed procedure for replacing the front wheels. However, here is what you need to know:

Wheel Maintenance

The manual recommends regularly cleaning the front wheels and rear drive wheels with a damp cloth or a soft-bristle brush to ensure their proper functioning.

Wheel Replacement

To obtain compatible replacement wheels for your robotic mower, you need to contact an authorized WORX dealer. They will be able to provide you with genuine spare parts and advise you on installation if necessary.

You can also contact WORX customer service directly to find out the exact references for the front wheels (part 18 in the technical documentation) to facilitate your order.

Question 2

What is the exact cutting height at position 5 on the WORX WG743E mower?

Accepted Answer

The WORX WG743E offers 7 height adjustment positions ranging from 20 mm to 80 mm. The adjustment is made progressively across the entire available range.

However, the technical manual does not specify the exact values in millimeters for each individual position (including position 5). The 7 positions are evenly distributed across the 20-80 mm range, suggesting a step of about 10 mm between each position. For reference, position 5 would therefore be around 60 mm, but this value is not officially confirmed by WORX in the provided documentation.

To know the precise height of position 5, please refer to the adjustment diagram illustrated (Fig. I) in your paper manual, or contact WORX customer service directly, who can provide you with this detailed technical information.

Question 3

What is the recommended sharpening frequency for the blade of the WORX WG743E mower?

Accepted Answer

According to the documentation for the WORX WG743E, sharpening the blade twice per mowing season is generally sufficient under normal conditions.

However, if your lawn has sandy or rocky soil, more frequent sharpening may be necessary as sand wears down the sharp edges more quickly.

Blade Replacement

The blade should be replaced after 50 hours of mowing or every 2 years, whichever comes first. Immediately replace any bent or damaged blade.

Key Points for Sharpening

Maintain the balance of the blade
Respect the original cutting angle
Sharpen both ends by removing equal amounts of material
Keep the blade sharp for better mowing performance

Question 4

Where is the USB port on the WORX Landroid L WR155E mower?

Accepted Answer

The USB port of the WORX Landroid L WR155E is located inside the battery cover, accessible at the back of the device.

How to access it

Open the battery cover located at the back of the mower
The USB port is directly visible and accessible in this space

What is this USB port used for?

This port is used to perform manual firmware updates for the device. You can update your Landroid L WR155E in two ways:

OTA (Over-The-Air) update: Connect the device to the 2.4 GHz WiFi via the app to receive automatic updates
USB stick update: Insert a USB stick formatted in FAT32 into the USB port to force a manual update

Question 5

How to install the side discharge cover?

Accepted Answer

The side discharge cover is one of the essential parts of the initial assembly kit for your WORX WG751.3 mower. This part, included in the box, directs the cut grass to the side of the device.

Installation Procedure

Detailed installation instructions for the side discharge cover are provided in the ASSEMBLY & OPERATION section of your manual, in figures E1 and E2. These illustrations show step by step:

The exact location to attach the cover to the chassis
The correct orientation of the cover
The attachment and locking points

Before use, ensure that the cover is completely locked and securely attached. A poorly installed cover could detach during use.

Refer to figures E1 and E2 of the PDF manual above for precise visual details, or download the complete guide if you need further clarifications.

User manual WORX Lawn mower : user manuals and guides in PDF

Models WORX Lawn mower most viewed

Other categories WORX

Recent questions about Lawn mower WORX