GDR 10 8LI - Screwdriver BOSCH - Free user manual and instructions

USER MANUAL GDR 10 8LI BOSCH

OBJ_DOKU-18832-004.fm Page 1 Tuesday, June 18, 2013 10:15 AM2 |

OBJ_BUCH-1066-004.book Page 2 Tuesday, June 18, 2013 10:16 AM3 |

OBJ_BUCH-1066-004.book Page 3 Tuesday, June 18, 2013 10:16 AM4 |

OBJ_BUCH-1066-004.book Page 4 Tuesday, June 18, 2013 10:16 AM5 |

OBJ_BUCH-1066-004.book Page 5 Tuesday, June 18, 2013 10:16 AM6 | Deutsch 1 609 92A 0BV | (18.6.13) Bosch Power Tools Deutsch

WARNUNG OBJ_BUCH-1066-004.book Page 6 Tuesday, June 18, 2013 10:16 AMDeutsch | 7

2004/108/EG, 2006/42/EG.

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 8 Tuesday, June 18, 2013 10:16 AMDeutsch | 9

OBJ_BUCH-1066-004.book Page 9 Tuesday, June 18, 2013 10:16 AM10 | Deutsch

OBJ_BUCH-1066-004.book Page 10 Tuesday, June 18, 2013 10:16 AMEnglish | 11 Bosch Power Tools 1 609 92A 0BV | (18.6.13) Transport

General Power Tool Safety Warnings

Read all safety warnings and all in-

structions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or seri-

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

 Keep work area clean and well lit. Cluttered or dark areas

 Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust

 Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

 Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

 Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

 Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

 Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges and moving parts. Damaged

or entangled cords increase the risk of electric shock.

 When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suitable

for outdoor use reduces the risk of electric shock.

 If operating a power tool in a damp location is unavoid-

able, use a residual current device (RCD) protected

supply. Use of an RCD reduces the risk of electric shock.

 Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while op-

erating power tools may result in serious personal injury.

 Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

WARNING OBJ_BUCH-1066-004.book Page 11 Tuesday, June 18, 2013 10:16 AM12 | English

1 609 92A 0BV | (18.6.13) Bosch Power Tools

 Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or en-

ergising power tools that have the switch on invites acci-

 Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a ro-

tating part of the power tool may result in personal injury.

 Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

 Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or long hair can be

caught in moving parts.

 If devices are provided for the connection of dust ex-

traction and collection facilities, ensure these are con-

nected and properly used. Use of dust collection can re-

duce dust-related hazards.

Power tool use and care

 Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

 Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

 Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

 Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

 Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power

 Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

 Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

Battery tool use and care

 Recharge only with the charger specified by the manu-

facturer. A charger that is suitable for one type of battery

pack may create a risk of fire when used with another bat-

 Use power tools only with specifically designated bat-

tery packs. Use of any other battery packs may create a

risk of injury and fire.

 When battery pack is not in use, keep it away from oth-

er metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

 Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally oc-

curs, flush with water. If liquid contacts eyes, addition-

ally seek medical help. Liquid ejected from the battery

may cause irritation or burns.

 Have your power tool serviced by a qualified repair per-

son using only identical replacement parts. This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Screwdrivers

 Hold power tool by insulated gripping surfaces, when

performing an operation where the fastener may con-

tact hidden wiring. Fasteners contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

 Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

 Always wait until the machine has come to a complete

stop before placing it down. The tool insert can jam and

lead to loss of control over the power tool.

 Do not open the battery. Danger of short-circuiting.

Protect the battery against heat, e. g., against

continuous intense sunlight, fire, water, and

moisture. Danger of explosion.

 In case of damage and improper use of the battery, va-

pours may be emitted. Ventilate the area and seek

medical help in case of complaints. The vapours can irri-

tate the respiratory system.

 Use the battery only in conjunction with your Bosch

power tool. This measure alone protects the battery

against dangerous overload.

 Use only original Bosch batteries with the voltage list-

ed on the nameplate of your power tool. When using oth-

er batteries, e.g. imitations, reconditioned batteries or

other brands, there is danger of injury as well as property

damage through exploding batteries.

Product Description and Specifica-

Read all safety warnings and all instruc-

tions. Failure to follow the warnings and in-

structions may result in electric shock, fire

and/or serious injury.

While reading the operating instructions, unfold the graphics

page for the machine and leave it open.

OBJ_BUCH-1066-004.book Page 12 Tuesday, June 18, 2013 10:16 AMEnglish | 13 Bosch Power Tools 1 609 92A 0BV | (18.6.13) Intended Use

The machine is intended for driving in and loosening screws

and bolts as well as for tightening and loosening nuts within

the respective range of dimension.

The light of this power tool is intended to illuminate the power

tool’s direct area of working operation and is not suitable for

household room illumination.

The numbering of the product features refers to the illustra-

tion of the machine on the graphics page.

1 Screwdriver bit with ball catch*

5 Fixture for carrying strap

10 Battery charge-control indicator

11 Handle (insulated gripping surface)

12 Universal bit holder*

*Accessories shown or described are not part of the standard de-

livery scope of the product. A complete overview of accessories

can be found in our accessories program.

Noise/Vibration Information

Measured sound values determined according to EN 60745.

Typically the A-weighted noise levels of the product are:

Sound pressure level 87 dB(A); Sound power level 98 dB(A).

(triax vector sum) and uncertainty K

determined according to EN 60745:

Impact tightening of fasteners of the maximum capacity of the

The vibration emission level given in this information sheet has

been measured in accordance with a standardised test given

in EN 60745 and may be used to compare one tool with anoth-

er. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main ap-

plications of the tool. However if the tool is used for different

applications, with different accessories or poorly maintained,

the vibration emission may differ. This may significantly in-

crease the exposure level over the total working period.

An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may signif-

icantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep hands warm, organise work patterns.

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with the fol-

lowing standards or standardisation documents: EN 60745

according to the provisions of the directives 2009/125/EC

(Regulation 1194/2012), 2011/65/EU, 2004/108/EC,

D-70745 Leinfelden-Echterdingen Robert Bosch GmbH, Power Tools DivisionD-70745 Leinfelden-Echterdingen08.04.2013 Assembly

Battery Charging (see figure A)

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The Lithium-Ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Cordless Impact Screwdriver GDR 10,8-LI Article number

Maximum torque, hard screw-

driving application according

EPTA-Procedure 01/2003

kg 1.0 Technical data determined with battery from delivery scope. Henk Becker

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 13 Tuesday, June 18, 2013 10:16 AM14 | English

1 609 92A 0BV | (18.6.13) Bosch Power Tools

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

To remove the battery 7 press the unlocking buttons 6 and

pull out the battery downwards. Do not exert any force.

The battery is equipped with a NTC temperature control

which allows charging only within a temperature range of be-

tween 0 °C and 45 °C. A long battery service life is achieved

Observe the notes for disposal.

Changing the Tool (see figure B)

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

Pull the locking sleeve 3 forward, push the insert tool to the

stop into the tool holder 2 and release the locking sleeve 3 to

lock the insert tool.

Use only screwdriver bits with ball catch 1 (DIN 3126-E6.3).

Other screwdriver bits 13 can be used with a universal bit

holder with ball catch 12.

Pull the locking sleeve 3 forward and remove the insert tool.

The tool holder 2 with the tool is driven by an electric motor

via a gear and impact mechanism.

The working procedure is divided into two phases:

Screwing in and tightening (impact mechanism in action).

The impact mechanism is activated as soon as the screwed

connection runs tight and thus load is put on the motor. In this

instance, the impact mechanism converts the power of the

motor to steady rotary impacts. When loosening screws or

nuts, the process is reversed.

Inserting the battery

 Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Us-

ing other batteries can lead to injuries and pose a fire haz-

Note: Use of batteries not suitable for the machine can lead to

malfunctions of or cause damage to the power tool.

Set the rotational direction switch 8 to the centre position in

order to avoid unintentional starting. Insert the charged bat-

tery 7 into the handle so that it can be felt to engage and faces

flush against the handle.

Reversing the rotational direction (see figure C)

The rotational direction switch 8 is used to reverse the rota-

tional direction of the machine. However, this is not possible

with the On/Off switch 9 actuated.

Right rotation: For driving in screws and tightening nuts,

press the rotational direction switch 8 through to the left stop.

Left Rotation: For loosening and unscrewing screws and

nuts, press the rotational direction switch 8 through to the

Switching On and Off

To start the machine, press the On/Off switch 9 and keep it

The power light 4 lights up when the On/Off switch 9 is slightly

or completely pressed, and allows the work area to be illumi-

nated when lighting conditions are insufficient.

To switch off the machine, release the On/Off switch 9.

To save energy, only switch the power tool on when using it.

The speed of the switched on power tool can be variably ad-

justed, depending on how far the On/Off switch 9 is pressed.

Light pressure on the On/Off switch 9 results in a low rotation-

al speed. Further pressure on the switch results in an increase

Battery Charge-control Indication

The battery charge-control indicator 10 consists of three

green LEDs, and indicates the charge condition of the battery

for a few seconds when the On/Off switch 9 is pressed half-

Temperature Dependent Overload Protection

When using as intended for, the power tool cannot be subject

to overload. When the load is too high or the allowable battery

temperature range of 0–70 °C is exceeded, the speed is re-

duced. The power tool will not run at full speed until reaching

the allowable battery temperature.

Protection Against Deep Discharging

The Lithium-Ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Apply the power tool to the screw/nut only when it is

switched off. Rotating tool inserts can slip off.

The torque depends on the impact duration. The maximum

achieved torque results from the sum of all individual torques

achieved through impact. The maximum torque is achieved

after an impact duration of 6–10 seconds. After this dura-

tion, the tightening torque is increased only minimally.

Continuous lighting 3 x green ≥ 2/3

Continuous lighting 2 x green ≥1/3

Continuous lighting 1 x green < 1/3

Flashing light 1 x green Reserve

OBJ_BUCH-1066-004.book Page 14 Tuesday, June 18, 2013 10:16 AMEnglish | 15

Bosch Power Tools 1 609 92A 0BV | (18.6.13)

The impact duration is to be determined for each required

tightening torque. The actually achieved tightening torque is

always to be checked with a torque wrench.

Screw Applications with Hard, Spring-loaded or Soft Seat

When in a test, the achieved torques in an impact series are

measured and transferred into a diagram, resulting in the

curve of a torque characteristic. The height of the curve corre-

sponds with the maximum reachable torque, and the steep-

ness indicates the duration in which this is achieved.

A torque gradient depends on the following factors:

– Strength properties of the screws/nuts

– Type of backing (washer, disc spring, seal)

– Strength properties of the material being screwed/bolted

– Lubrication conditions at the screw/bolt connection

The following application cases result accordingly:

– A hard seat is given for metal-to-metal screw applications

with the use of washers. After a relatively short impact du-

ration, the maximum torque is reached (steep characteris-

tic curve). Unnecessary long impact duration only causes

damage to the machine.

– A spring-loaded seat is given for metal-to-metal screw ap-

plications, however with the use of spring washers, disc

springs, studs or screws/nuts with conical seat as well as

when using extensions.

– A soft seat is given for screw applications, e. g., metal on

wood or when using lead washers or fibre washers as back-

For a spring-loaded seat as well as for a soft seat, the maxi-

mum tightening torque is lower than for a hard seat. Also, a

clearly longer impact duration is required.

Reference Values for Maximum Screw/Bolt Tightening Torques

Calculated from the tensional cross-section; utilization of the yield point 90 % (with friction coefficient μ total = 0.12). As a control

measure, always check the tightening torque with a torque wrench.

Before screwing larger, longer screws into hard materials, it is

advisable to predrill a pilot hole with the core diameter of the

of the screw length.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

 For safe and proper working, always keep the machine

and ventilation slots clean.

When the battery is no longer operative, please refer to an au-

thorised after-sales service agent for Bosch power tools.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can al-

Bosch’s application service team will gladly answer questions

concerning our products and their accessories.

In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of

Robert Bosch Ltd. (B.S.C.)

Property Classes accord-

Standard Screws/Bolts High-strength Bolts

22.6 30 37.6 40 45 50 60 67 80 113 135

OBJ_BUCH-1066-004.book Page 15 Tuesday, June 18, 2013 10:16 AM16 | Français 1 609 92A 0BV | (18.6.13) Bosch Power Tools Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Customer Contact Center

Republic of South Africa

Hotline: (011) 6519600

35 Roper Street, New Centre

E-Mail: bsctools@icon.co.za

KZN – BSC Service Centre

Unit E, Almar Centre

E-Mail: bsc.dur@za.bosch.com

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

The contained lithium ion batteries are subject to the Danger-

ous Goods Legislation requirements. The user can transport

the batteries by road without further requirements.

When being transported by third parties (e.g.: air transport or

forwarding agency), special requirements on packaging and

labelling must be observed. For preparation of the item being

shipped, consulting an expert for hazardous material is re-

Dispatch batteries only when the housing is undamaged.

Tape or mask off open contacts and pack up the battery in

such a manner that it cannot move around in the packaging.

Please also observe possibly more detailed national regula-

The machine, rechargeable batteries, accessories

and packaging should be sorted for environmental-

Do not dispose of power tools and batteries/rechargeable

batteries into household waste!

Only for EC countries:

According to the European Guideline

2012/19/EU, power tools that are no long-

er usable, and according to the European

Guideline 2006/66/EC, defective or used

battery packs/batteries, must be collected

separately and disposed of in an environ-

mentally correct manner.

Batteries no longer suitable for use can be directly returned

Robert Bosch Ltd. (B.S.C.)

Battery packs/batteries:

Please observe the instructions in sec-

AVERTISSEMENT OBJ_BUCH-1066-004.book Page 16 Tuesday, June 18, 2013 10:16 AMFrançais | 17

2004/108/CE, 2006/42/CE.

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 19 Tuesday, June 18, 2013 10:16 AM20 | Français

OBJ_BUCH-1066-004.book Page 20 Tuesday, June 18, 2013 10:16 AMFrançais | 21

ADVERTENCIA OBJ_BUCH-1066-004.book Page 22 Tuesday, June 18, 2013 10:16 AMEspañol | 23

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 25 Tuesday, June 18, 2013 10:16 AM26 | Español

OBJ_BUCH-1066-004.book Page 26 Tuesday, June 18, 2013 10:16 AMEspañol | 27

2004/108/CE, 2006/42/CE.

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 30 Tuesday, June 18, 2013 10:16 AMPortuguês | 31

OBJ_BUCH-1066-004.book Page 31 Tuesday, June 18, 2013 10:16 AM32 | Português

Conforme as Directivas Europeias

AVVERTENZA OBJ_BUCH-1066-004.book Page 33 Tuesday, June 18, 2013 10:16 AM34 | Italiano

OBJ_BUCH-1066-004.book Page 34 Tuesday, June 18, 2013 10:16 AMItaliano | 35 Bosch Power Tools 1 609 92A 0BV | (18.6.13) Assistenza

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 36 Tuesday, June 18, 2013 10:16 AMItaliano | 37

OBJ_BUCH-1066-004.book Page 37 Tuesday, June 18, 2013 10:16 AM38 | Italiano

WAARSCHUWING OBJ_BUCH-1066-004.book Page 39 Tuesday, June 18, 2013 10:16 AM40 | Nederlands

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 41 Tuesday, June 18, 2013 10:16 AM42 | Nederlands

OBJ_BUCH-1066-004.book Page 42 Tuesday, June 18, 2013 10:16 AMNederlands | 43

ADVARSEL OBJ_BUCH-1066-004.book Page 44 Tuesday, June 18, 2013 10:16 AMDansk | 45

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 46 Tuesday, June 18, 2013 10:16 AMDansk | 47

OBJ_BUCH-1066-004.book Page 47 Tuesday, June 18, 2013 10:16 AM48 | Dansk

Bosch Service Center

OBJ_BUCH-1066-004.book Page 50 Tuesday, June 18, 2013 10:16 AMSvenska | 51

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 51 Tuesday, June 18, 2013 10:16 AM52 | Svenska

Bosch Service Center

ADVARSEL OBJ_BUCH-1066-004.book Page 53 Tuesday, June 18, 2013 10:16 AM54 | Norsk

OBJ_BUCH-1066-004.book Page 54 Tuesday, June 18, 2013 10:16 AMNorsk | 55 Bosch Power Tools 1 609 92A 0BV | (18.6.13) Service

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 56 Tuesday, June 18, 2013 10:16 AMNorsk | 57

VAROITUS OBJ_BUCH-1066-004.book Page 58 Tuesday, June 18, 2013 10:16 AMSuomi | 59

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 60 Tuesday, June 18, 2013 10:16 AMSuomi | 61

OBJ_BUCH-1066-004.book Page 61 Tuesday, June 18, 2013 10:16 AM62 | Suomi

OBJ_BUCH-1066-004.book Page 63 Tuesday, June 18, 2013 10:16 AM64 | Ελληνικά

OBJ_BUCH-1066-004.book Page 65 Tuesday, June 18, 2013 10:16 AM66 | Ελληνικά

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 66 Tuesday, June 18, 2013 10:16 AMΕλληνικά | 67

Executive Vice President

Head of Product Certification

Akülü darbeli tork anahtarı GDR 10,8-LI Teknik veriler teslimat kapsamındaki akü ile tespit edilmiştir.

OBJ_BUCH-1066-004.book Page 71 Tuesday, June 18, 2013 10:16 AM72 | Türkçe

OBJ_BUCH-1066-004.book Page 72 Tuesday, June 18, 2013 10:16 AMTürkçe | 73

OBJ_BUCH-1066-004.book Page 73 Tuesday, June 18, 2013 10:16 AM74 | Polski 1 609 92A 0BV | (18.6.13) Bosch Power Tools Aygem

2004/108/WE, 2006/42/WE.

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 77 Tuesday, June 18, 2013 10:16 AM78 | Polski

OBJ_BUCH-1066-004.book Page 78 Tuesday, June 18, 2013 10:16 AMPolski | 79

Robert Bosch Sp. z o.o.

OBJ_BUCH-1066-004.book Page 79 Tuesday, June 18, 2013 10:16 AM80 | Česky 1 609 92A 0BV | (18.6.13) Bosch Power Tools Akumulatory/Baterie:

OBJ_BUCH-1066-004.book Page 81 Tuesday, June 18, 2013 10:16 AM82 | Česky

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 82 Tuesday, June 18, 2013 10:16 AMČesky | 83

POZOR OBJ_BUCH-1066-004.book Page 84 Tuesday, June 18, 2013 10:16 AMSlovensky | 85

OBJ_BUCH-1066-004.book Page 85 Tuesday, June 18, 2013 10:16 AM86 | Slovensky

OBJ_BUCH-1066-004.book Page 86 Tuesday, June 18, 2013 10:16 AMSlovensky | 87 Bosch Power Tools 1 609 92A 0BV | (18.6.13) 9 Vypínač

2011/65/EÚ, 2004/108/ES, 2006/42/ES.

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 87 Tuesday, June 18, 2013 10:16 AM88 | Slovensky

OBJ_BUCH-1066-004.book Page 88 Tuesday, June 18, 2013 10:16 AMSlovensky | 89

FIGYELMEZTETÉS OBJ_BUCH-1066-004.book Page 90 Tuesday, June 18, 2013 10:16 AMMagyar | 91

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 93 Tuesday, June 18, 2013 10:16 AM94 | Magyar

OBJ_BUCH-1066-004.book Page 94 Tuesday, June 18, 2013 10:16 AMРусский | 95 Bosch Power Tools 1 609 92A 0BV | (19.6.13) Tippek

No. C-DE.АЯ46.B.46459

OBJ_DOKU-27585-003.fm Page 95 Wednesday, June 19, 2013 8:40 AM96 | Русский

OBJ_BUCH-1066-004.book Page 96 Tuesday, June 18, 2013 10:16 AMРусский | 97

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 98 Tuesday, June 18, 2013 10:16 AMРусский | 99

OBJ_BUCH-1066-004.book Page 99 Tuesday, June 18, 2013 10:16 AM100 | Русский

OBJ_BUCH-1066-004.book Page 100 Tuesday, June 18, 2013 10:16 AMРусский | 101

Executive Vice President

Head of Product Certification

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 110 Tuesday, June 18, 2013 10:16 AMҚaзақша | 111

OBJ_BUCH-1066-004.book Page 111 Tuesday, June 18, 2013 10:16 AM112 | Қaзақша

AVERTISMENT OBJ_BUCH-1066-004.book Page 113 Tuesday, June 18, 2013 10:16 AM114 | Română

2011/65/UE, 2004/108/CE, 2006/42/CE.

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 115 Tuesday, June 18, 2013 10:16 AM116 | Română

OBJ_BUCH-1066-004.book Page 116 Tuesday, June 18, 2013 10:16 AMRomână | 117

OBJ_BUCH-1066-004.book Page 117 Tuesday, June 18, 2013 10:16 AM118 | Български 1 609 92A 0BV | (18.6.13) Bosch Power Tools Sfaturi utile

Directivei Europene 2006/66/CE, acumu-

OBJ_BUCH-1066-004.book Page 118 Tuesday, June 18, 2013 10:16 AMБългарски | 119

OBJ_BUCH-1066-004.book Page 119 Tuesday, June 18, 2013 10:16 AM120 | Български

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 121 Tuesday, June 18, 2013 10:16 AM122 | Български

OBJ_BUCH-1066-004.book Page 122 Tuesday, June 18, 2013 10:16 AMБългарски | 123

Executive Vice President

Head of Product Certification

UPOZORENJE OBJ_BUCH-1066-004.book Page 130 Tuesday, June 18, 2013 10:16 AMSrpski | 131

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 132 Tuesday, June 18, 2013 10:16 AMSrpski | 133

OBJ_BUCH-1066-004.book Page 133 Tuesday, June 18, 2013 10:16 AM134 | Srpski

OPOZORILO OBJ_BUCH-1066-004.book Page 135 Tuesday, June 18, 2013 10:16 AM136 | Slovensko

2004/108/ES, 2006/42/ES.

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 137 Tuesday, June 18, 2013 10:16 AM138 | Slovensko

OBJ_BUCH-1066-004.book Page 138 Tuesday, June 18, 2013 10:16 AMSlovensko | 139

UPOZORENJE OBJ_BUCH-1066-004.book Page 140 Tuesday, June 18, 2013 10:16 AMHrvatski | 141

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 142 Tuesday, June 18, 2013 10:16 AMHrvatski | 143

OBJ_BUCH-1066-004.book Page 143 Tuesday, June 18, 2013 10:16 AM144 | Hrvatski

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 147 Tuesday, June 18, 2013 10:16 AM148 | Eesti

OBJ_BUCH-1066-004.book Page 151 Tuesday, June 18, 2013 10:16 AM152 | Latviešu

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 152 Tuesday, June 18, 2013 10:16 AMLatviešu | 153

OBJ_BUCH-1066-004.book Page 153 Tuesday, June 18, 2013 10:16 AM154 | Latviešu

OBJ_BUCH-1066-004.book Page 155 Tuesday, June 18, 2013 10:16 AM156 | Lietuviškai

Executive Vice President

Head of Product Certification

OBJ_BUCH-1066-004.book Page 157 Tuesday, June 18, 2013 10:16 AM158 | Lietuviškai

OBJ_BUCH-1066-004.book Page 158 Tuesday, June 18, 2013 10:16 AMLietuviškai | 159

OBJ_BUCH-1066-004.book Page 159 Tuesday, June 18, 2013 10:16 AM160 | Lietuviškai

M 62.713.614.524.85.426.027.228.139.713.616.2

Head of Product Certification

Executive Vice President

M 62.713.614.524.85.426.027.228.139.713.616.2

Head of Product Certification

Executive Vice President