Q: How does the air flow inversion work?

The ELICA SHEENS hood does not have an inversion function to change the direction of ventilation. However, it offers two distinct operating modes : Extraction mode : vapors are expelled directly to the outside (requires a duct for evacuation) Filtering mode : the sucked air is degreased and deodorized before being returned to the kitchen (without external evacuation) The choice between these two modes is made during installation according to your configuration (possibility of external evacuation or not). Once installed, the hood operates in the intended mode. The hood also has 3 suction speeds (T1, T2, T3) and a Booster mode (5 minutes at maximum power) to adapt the ventilation to your needs.

Q: How to install the grease and charcoal filters of the ELICA APLOMB hood?

Before proceeding, turn off the hood. Metal grease filter The grease filter captures cooking particles. To install it: Position it in place and push until it clicks into place To remove it, pull on the release spring lever Maintenance: Clean it every month with a mild detergent, by hand or in the dishwasher (short cycle, low temperature). The manual indicates an alert every 40 hours of use. Active charcoal filter This filter eliminates bad cooking odors. It is exclusive to filtering versions (air recycling). Place one filter on each side on the two protective grids of the motor arms Turn clockwise to secure Turn counterclockwise to remove Important: The charcoal filter cannot be cleaned or regenerated . It must be replaced every 4 months at most. The actual duration depends on your frequency of use. The manual indicates an alert every 160 hours of use.

Q: What is the minimum distance that must be maintained between this extractor hood and the rear wall during installation?

Distance above the cooktop: For a gas cooktop like yours, the FOLD BL MAT/A/52 requires a minimum of 65 cm between the cooking surface and the bottom of the hood. With your height of 75 cm, you are above this limit - it is compliant. ✓ Distance from the rear wall: The manual for the FOLD BL MAT/A/52 does not specify a specific minimum distance to maintain between the hood and the rear wall. In practice, for this type of extractor hood, you should leave enough space to: Easily access the control panel (usually a few centimeters) Ensure good air circulation behind the hood (at least 5-10 cm) Allow for the connection of the duct (check the diameter of your extraction connection) To know the exact distance from the rear wall specific to your configuration and type of duct, refer to the installation diagram in the PDF, or contact ELICA support with your model and type of extraction (wall-mounted or ducted).

Q: At what height should the electrical outlet be installed for an Elica Thin P 60 X hood?

The manual for the Elica Thin P 60 X hood specifies that the electrical outlet must remain accessible after the installation of the hood. There is no fixed height recommended by the manufacturer. In practice, the outlet should be: Accessible and not obscured by the hood once installed Out of direct reach of the exhaust duct (if external venting) or the charcoal filter (if recirculating) Compliant with local electrical standards of your country or region The standard height is generally between 1.5 m and 2 m above the floor, according to current NF standards. For a safe installation, consult local electrical regulations or a qualified electrician. Technical note: The hood operates at 220-240 V / 50 Hz with 3 speeds plus Boost mode.

Question 1

How does the air flow inversion work?

Accepted Answer

The ELICA SHEENS hood does not have an inversion function to change the direction of ventilation. However, it offers two distinct operating modes:

Extraction mode: vapors are expelled directly to the outside (requires a duct for evacuation)
Filtering mode: the sucked air is degreased and deodorized before being returned to the kitchen (without external evacuation)

The choice between these two modes is made during installation according to your configuration (possibility of external evacuation or not). Once installed, the hood operates in the intended mode.

The hood also has 3 suction speeds (T1, T2, T3) and a Booster mode (5 minutes at maximum power) to adapt the ventilation to your needs.

Question 2

How to install the grease and charcoal filters of the ELICA APLOMB hood?

Accepted Answer

Before proceeding, turn off the hood.

Metal grease filter

The grease filter captures cooking particles. To install it:

Position it in place and push until it clicks into place
To remove it, pull on the release spring lever

Maintenance: Clean it every month with a mild detergent, by hand or in the dishwasher (short cycle, low temperature). The manual indicates an alert every 40 hours of use.

Active charcoal filter

This filter eliminates bad cooking odors. It is exclusive to filtering versions (air recycling).

Place one filter on each side on the two protective grids of the motor arms
Turn clockwise to secure
Turn counterclockwise to remove

Important: The charcoal filter cannot be cleaned or regenerated. It must be replaced every 4 months at most. The actual duration depends on your frequency of use. The manual indicates an alert every 160 hours of use.

Question 3

What does error code E2 mean on an ELICA NikolaTesla FIT XL cooktop?

Accepted Answer

Error E2 indicates an internal overheating of the electronics of your ELICA NikolaTesla FIT XL PRF0186750 cooktop. This means that the temperature of the electronic components has exceeded the safety threshold.

Possible causes

Prolonged operation at maximum power (high power levels or booster activated)
Insufficient ventilation around the cooktop or obstruction of the air vents
Accumulation of dust or debris blocking air circulation to the integrated hood
Ambient temperature too high in the kitchen

What to do immediately

Turn off the cooktop immediately by pressing the stop button
Allow it to cool completely for at least 30-45 minutes before any reuse
Do not use the appliance while it is cooling

How to prevent this from happening again

Check that the ventilation grilles (front and back) are not obstructed
Ensure there is sufficient space (at least 5 cm) around your cooktop for air circulation
Limit the use of booster modes (5 min and 15 min) to short durations
Regularly clean the suction area of the integrated hood to prevent accumulation

If error E2 reappears after complete cooling and you have checked the ventilation, contact the authorized ELICA technical service for an inspection of the internal cooling system.

Question 4

What does the code "L" displayed on my ELICA NikolaTesla Prime+ cooktop mean?

Accepted Answer

The code "L" is not listed in the official documentation for the ELICA NikolaTesla Prime+ cooktop.

According to the provided manual, the documented error codes are:

E2: Overheating - "The control zone turns off due to too high a temperature"
E3: Incompatible container
E5: Communication issues between the user interface

If the code "L" appears upon startup, it may represent:

A functioning indicator (like "H" for residual heat or "R" for automatic preheating)
An undocumented error code requiring technical intervention

Solutions:

Check that the lock button is not activated (safety feature against accidental activation)
Turn off the cooktop and turn it back on after 30 seconds
If the message persists, contact ELICA technical service to accurately identify this code specific to your device

Question 5

What is the minimum distance that must be maintained between this extractor hood and the rear wall during installation?

Accepted Answer

Distance above the cooktop: For a gas cooktop like yours, the FOLD BL MAT/A/52 requires a minimum of 65 cm between the cooking surface and the bottom of the hood. With your height of 75 cm, you are above this limit - it is compliant. ✓

Distance from the rear wall: The manual for the FOLD BL MAT/A/52 does not specify a specific minimum distance to maintain between the hood and the rear wall. In practice, for this type of extractor hood, you should leave enough space to:

Easily access the control panel (usually a few centimeters)
Ensure good air circulation behind the hood (at least 5-10 cm)
Allow for the connection of the duct (check the diameter of your extraction connection)

To know the exact distance from the rear wall specific to your configuration and type of duct, refer to the installation diagram in the PDF, or contact ELICA support with your model and type of extraction (wall-mounted or ducted).

Question 6

How to install the charcoal filters in the ELICA FOLD BL MAT/A/52 vacuum cleaner?

Accepted Answer

Here’s how to install the charcoal filters in your ELICA FOLD BL MAT/A/52:

Installation Steps

Remove the grease filters from the suction unit.
Place one charcoal filter on each side of the device.
Hang the charcoal filters onto the product by securing them properly.
Replace the grease filters over the charcoal filters.

Activating the Filtering Mode

Once the charcoal filters are installed, you need to activate the charcoal filter indicator for the hood to operate in filtering mode (internal recycling):

Set the device to OFF mode.
Press and hold the T1 and T4 buttons simultaneously for 3 seconds.
The L1 and L2 indicators will blink for 5 seconds to confirm activation.

Important: Charcoal filters are only necessary if you use the hood in filtering mode. In standard configuration (external discharge), these filters are not required.

Question 7

How to reset the carbon filters of the ELICA SHEENS hood?

Accepted Answer

The procedure for resetting the carbon filters depends on the type of filter maintained:

Grease filter

This filter must be reset every 40 hours of use.

Procedure: When the hood is off and the indicators T1+T2 are flashing, press and hold this button combination for 10 seconds. The indicators will flash quickly twice to confirm the reset.

Odor filter (activated carbon)

This filter must be reset every 160 hours of use.

Procedure: When the hood is off and the indicators T1+T3 are flashing, press and hold this button combination for 10 seconds. The indicators will flash quickly twice to confirm the reset.

Maintenance of the washable carbon filter

In addition to the reset, the washable activated carbon filter can be regenerated every 2 months: wash it with hot water and appropriate detergents, then let it dry. The internal pad should be replaced every 3 years.

Question 8

At what height should the electrical outlet be installed for an Elica Thin P 60 X hood?

Accepted Answer

The manual for the Elica Thin P 60 X hood specifies that the electrical outlet must remain accessible after the installation of the hood. There is no fixed height recommended by the manufacturer.

In practice, the outlet should be:

Accessible and not obscured by the hood once installed
Out of direct reach of the exhaust duct (if external venting) or the charcoal filter (if recirculating)
Compliant with local electrical standards of your country or region

The standard height is generally between 1.5 m and 2 m above the floor, according to current NF standards. For a safe installation, consult local electrical regulations or a qualified electrician.

Technical note: The hood operates at 220-240 V / 50 Hz with 3 speeds plus Boost mode.

Question 9

What is the sound signal (beep signal) of the ELICA WISE hood and when does it activate?

Accepted Answer

The sound signal (beep) of the ELICA WISE hood activates in two situations:

After cleaning or replacing the filters

Once the filter maintenance is complete, press and hold the OFF button until the sound signal. This confirms that the maintenance alarm reset has been recorded by the device. The flashing LED indicator will turn off automatically.

Managing the charcoal filter alarm (6-button models)

For models equipped with 6 buttons, you can activate or deactivate the charcoal alarm. Sound signals accompany each step:

Press and hold the OFF button for 3 seconds to access the settings
Simultaneously press buttons 1 and 2 for 3 seconds to activate or deactivate the alarm
The sound signal confirms that the setting has been acknowledged

These acoustic signals are simply confirmations that the device has recorded your maintenance actions or settings.

Question 10

What does the flashing anti-drip indicator on my ELICA BOXIN NO DRIP mean?

Accepted Answer

The flashing indicator is not "anti-drip" in the strict sense. It is the active charcoal filter saturation indicator that signals it is time to replace it.

What does this flashing mean?

According to the manual for your ELICA BOXIN NO DRIP:

Fixed LED = the metal grease filter needs maintenance (cleaning at least once a month)
Flashing LED = the active charcoal filter needs to be replaced (every 4 months maximum)

How to remedy?

Since your indicator is flashing, you need to replace the charcoal filter. It is the recycling filter, not washable or regenerable.

About the "No Drip" system

The real anti-drip system of your hood is different: it uses invisible resistors that heat the lower surfaces to prevent condensation. The resulting condensation tray must be emptied at least once a week via the purge tab.

After replacing the charcoal filter, reset the indicator by pressing and holding the button (hood off).

User manual ELICA : user manuals and guides in PDF

Models ELICA most viewed

Browse manuals ELICA by appliance type

Recent questions about devices ELICA