KREA LX IX F/60 - Range hood ELICA - Free user manual and instructions
Find the device manual for free KREA LX IX F/60 ELICA in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Wall-mounted chimney range hood |
| Brand | Elica |
| Model | KREA LX IX F/60 |
| Mounting Type | Wall-mounted chimney hood |
| Width | 60 cm |
| Depth | Approximately 30 cm |
| Height (Chimney) | Adjustable, approximately 70–110 cm |
| Material | Stainless steel |
| Finish | Brushed stainless steel |
| Power Supply | 230 V / 50 Hz |
| Motor Power | Typical 220 W |
| Max Extraction Capacity | Around 600 m³/h |
| Number of Motors | 1 |
| Noise Level | Approximately 55–65 dB |
| Number of Speeds | 3 speeds |
| Controls | Electronic push buttons |
| Lighting | 2 × LED lamps (typical 3 W each) |
| Grease Filter | Aluminum mesh filter, washable |
| Charcoal Filter | Optional, for recirculation mode |
| Ducting Diameter | 150 mm |
| Energy Class | B (typical) |
| Installation Height | Min. 65 cm above electric hob, 75 cm above gas hob |
| Maintenance | Clean grease filter monthly; wipe surfaces with mild detergent |
| Safety Features | Thermal cutoff protection, motor overload safeguard |
Frequently Asked Questions - KREA LX IX F/60 ELICA
How to install the ELICA KREA LX IX F/60 range hood?
Ensure the wall is load-bearing and the installation height is at least 65 cm above an electric hob or 75 cm above a gas hob. Mark the mounting holes, drill, and secure the mounting bracket. Hang the hood, connect the ducting (diameter 150 mm) to the exhaust outlet, and wire the electrical supply to a 230 V socket. For recirculation mode, add charcoal filters and close the outlet.
How to clean the aluminum grease filters?
Remove the grease filters by pressing the release clip and pulling them down. Wash them in warm soapy water or in a dishwasher at a low temperature. Rinse and dry thoroughly before reinstalling. Clean them at least once a month to maintain extraction performance and reduce fire risk.
How to change the charcoal filter (recirculation mode)?
When using recirculation mode, the charcoal filter must be replaced every 3–6 months. To change it, release the grease filters, then unlock and slide out the charcoal filter. Install the new filter by aligning it with the slots and clicking it into place. Reattach the grease filters.
How to operate the touch controls?
The electronic push buttons allow you to toggle the fan between the available speeds (usually 2–3 levels) and switch the LED lights on or off. Press the speed button repeatedly to cycle through power settings. Some models feature an auto-stop timer; refer to the manual for exact control behavior.
What is the minimum installation height above a gas hob?
For gas hobs, ELICA recommends a minimum distance of 75 cm between the hob surface and the lowest part of the range hood. For electric hobs, the minimum is 65 cm. Always consult local building codes and the specific installation guide for your model.
Why is the hood not extracting effectively?
Check if the grease filters are clogged and clean them if necessary. Verify that the ducting is not blocked or excessively long/bent. Ensure that the room is sufficiently ventilated if using extraction mode. Also confirm that the fan speed is set to the appropriate level for the cooking activity.
Can the hood be used in recirculation mode?
Yes, the KREA LX IX F/60 can be used in recirculation mode with charcoal filters installed. In this configuration, the air is cleaned by the grease and charcoal filters, then returned to the kitchen. The charcoal filter is not supplied with the hood and must be purchased separately.
How to replace the LED lights?
Turn off the hood and disconnect power. Gently pry out the LED lamp holder using a small flat-head screwdriver, disconnect the wiring, and replace with a new LED module of the same type and rating. Reconnect the wires and push the holder back into place. If unsure, contact a qualified technician.
How to reset the filter saturation alarm?
Many Elica hoods have a filter alarm that lights up when the grease filter needs cleaning. After cleaning and reinstalling the filter, press and hold the lighting button (or speed button, depending on model) for about 3 seconds until the alarm light turns off. This resets the counter.
What maintenance is required for optimal performance?
Clean the grease filters monthly with mild detergent or in the dishwasher. Wipe the stainless steel surfaces with a soft, damp cloth and a non-abrasive cleaner. Replace charcoal filters regularly if used in recirculation mode. Inspect ducting for blockages and ensure the motor and fan are free of dust. This keeps the hood efficient and safe.
User questions about KREA LX IX F/60 ELICA
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Range hood in PDF format for free! Find your manual KREA LX IX F/60 - ELICA and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. KREA LX IX F/60 by ELICA.
USER MANUAL KREA LX IX F/60 ELICA
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ELICA
Model : KREA LX IX F/60
Category : Range hood