Q: How to check and ensure that the freezer maintains a temperature of -18°C?

The VALBERG UF NF 240 C S180C freezer has a digital display on the control panel that allows you to check the set temperature at any time. To check the current temperature: Check the digital screen of the freezer - it displays the programmed temperature in real time The recommended and optimal temperature for freezing food is -18°C To set or adjust to -18°C: Use the Set Temp button to scroll through the temperatures (available range: -14°C to -24°C) Each press of the button changes the setting by 1°C Press until the display shows -18°C Important: The digital display indicates the programmed temperature , but the actual temperature inside may vary slightly depending on the amount of food stored and its position. For a reliable check of the actual internal temperature, you can use a freezer thermometer placed in a glass or a small container. When first starting the freezer, set it to -18°C for optimal food preparation.

Q: How to activate the super freezing mode (freezing+) on the VALBERG CF 418 D?

The freezing+ mode is also called super mode on your VALBERG CF 418 D freezer. To activate it, simply press the button ⑦ marked "super" . If the buttons do not respond to your press, they are probably automatically locked at the start of the device. To unlock the controls, hold down button ⑦ for 3 seconds - the indicator will show that the buttons are now active. Once the super mode is activated: The temperature drops to -30°C for rapid freezing The mode operates for up to 24 hours maximum It stops automatically after 24h, in case of a power outage, or if you press the button again This mode is particularly useful when you want to freeze a large quantity of fresh food at once.

Q: What does the error code A45 F mean on the VALBERG CF 198 E W625C refrigerator and how can it be resolved?

The error code A45 F displayed on your VALBERG CF 198 E W625C refrigerator generally indicates a problem related to the operation of the appliance, often associated with a malfunction of the cooling system or an anomaly detected by the internal sensors. Possible meaning of code A45 F This code may signal: A temperature fault, for example, a temperature that is too high or a defective temperature sensor. A problem with the automatic defrosting system, such as excessive frost buildup. An electrical anomaly or an internal connection issue. What to do to resolve this issue? Check the temperature: Ensure that the temperature is set correctly, usually between 0 and 4 °C for the refrigerator section. Check the power supply: Make sure the appliance is properly plugged in and that the outlet is functioning correctly. Inspect the defrosting: If your model has automatic defrosting, check for excessive ice buildup that could hinder operation. Clean the ventilation grilles: Ensure they are not blocked by dust or objects. Restart: Unplug the appliance for a few minutes and then plug it back in to see if the code disappears. If after these checks the error code persists, it is recommended to contact a qualified technical service for a thorough diagnosis and possible repair.

Question 1

How to check and ensure that the freezer maintains a temperature of -18°C?

Accepted Answer

The VALBERG UF NF 240 C S180C freezer has a digital display on the control panel that allows you to check the set temperature at any time.

To check the current temperature:

Check the digital screen of the freezer - it displays the programmed temperature in real time
The recommended and optimal temperature for freezing food is -18°C

To set or adjust to -18°C:

Use the Set Temp button to scroll through the temperatures (available range: -14°C to -24°C)
Each press of the button changes the setting by 1°C
Press until the display shows -18°C

Important:

The digital display indicates the programmed temperature, but the actual temperature inside may vary slightly depending on the amount of food stored and its position. For a reliable check of the actual internal temperature, you can use a freezer thermometer placed in a glass or a small container.

When first starting the freezer, set it to -18°C for optimal food preparation.

Question 2

How do I set the freezing temperature on the VALBERG CF 198 E W625C?

Accepted Answer

The VALBERG CF 198 E W625C freezer has a temperature setting button (button 8), not a dial.

Adjustment procedure:

Press the temperature setting button (button 8) to adjust the temperature
With each press, the temperature changes by one degree Celsius or Fahrenheit
The numeric display shows the current temperature

Temperature range:

Minimum: -30°C (or -22°F)
Maximum: +10°C (or +50°F)
Default starting temperature: -18°C

Change the temperature scale:

Hold down button 8 for 3 seconds to switch between Celsius and Fahrenheit display.

Indicator lights on the panel show the active scale (Celsius or Fahrenheit).

Question 3

How to activate the super freezing mode (freezing+) on the VALBERG CF 418 D?

Accepted Answer

The freezing+ mode is also called super mode on your VALBERG CF 418 D freezer. To activate it, simply press the button ⑦ marked "super".

If the buttons do not respond to your press, they are probably automatically locked at the start of the device. To unlock the controls, hold down button ⑦ for 3 seconds - the indicator will show that the buttons are now active.

Once the super mode is activated:

The temperature drops to -30°C for rapid freezing
The mode operates for up to 24 hours maximum
It stops automatically after 24h, in case of a power outage, or if you press the button again

This mode is particularly useful when you want to freeze a large quantity of fresh food at once.

Question 4

What is the purpose of the button 7 marked 'super' on the VALBERG CF 418 D freezer?

Accepted Answer

The button ⑦ marked 'super' on your VALBERG CF 418 D W625C freezer is the Fast Freeze button. It is NOT the button to set the temperature normally.

Function of button ⑦ (Fast Freeze)

When you press this button, it activates the quick freezing mode, which forces the temperature to -30°C continuously for up to 24 hours. This is useful when you have just frozen large quantities of food or need maximum temporary freezing.

To set the temperature normally

You need to use the button ⑧ (temperature setting). Here’s how:

Press the button ⑧ to display the current temperature on the screen
Press again to change the temperature by 1°C with each press
The available range is from -16°C to -30°C
By default, the appliance starts at -18°C

If the buttons do not respond

The controls are locked by default when powered on. To unlock them, press and hold the button ⑦ for 3 seconds without releasing it. The buttons will then function normally.

Question 5

Why does the freezer temperature stay stuck at -18°C when I press the button?

Accepted Answer

If you press the temperature setting button (⑧) and the display remains stuck at -18°C, the controls on your device are likely locked by default.

To unlock the controls:

Press and hold the Freeze+ button for 3 seconds
Once unlocked, the buttons will become operational

After unlocking, you can adjust the temperature:

Press the temperature setting button once to display the current freezer temperature
Press this button again to change the temperature by 1 degree Celsius with each press
The adjustable range is from -16°C to -30°C

The default temperature at startup is -18°C. If you want a different temperature, you can adjust it according to your needs after unlocking.

Question 6

Why do the outer walls of the VALBERG UF NF 254 F S180C freezer get very hot?

Accepted Answer

If the outer walls of your VALBERG UF NF 254 F S180C freezer become very hot, it may indicate several situations:

Most common cause: Normal heating of the condenser

The condenser (thermal coil) is often located on the sides or at the back of the freezer. It naturally dissipates the heat extracted from the inside to maintain the temperature at -18°C (or your custom setting via the "temp" button). A slight heating is normal and expected. However, if it is excessive (too hot to keep your hand there for more than a few seconds), check the following points.

Possible issues

Dirty condenser: Dust and dirt reduce heat exchange. Regularly clean the rear and side grilles with a vacuum cleaner or a damp cloth (appliance turned off).
Overloaded freezer: An excessive amount of food reduces the circulation of cold air and forces the compressor to work harder, generating more external heat.
Room too hot: This VALBERG UF NF 254 F S180C model is rated multi-class (SN, N, ST, T). If your room exceeds 32°C-38°C according to your class, the freezer is working in overload. Ensure that the ambient temperature remains compliant with your usage (class N: 16-32°C by default).
Improperly closed door or damaged seal: A defective door seal or imperfect closure allows cold air leaks, forcing the compressor to run continuously and heating the walls further.
Cooling system failure (rare): If the heating is extreme and accompanied by poor internal freezing, a compressor or circuit issue may be the cause. Contact VALBERG support or a technician.

Practical recommendations

Set the temperature to -20°C via the "temp" button (recommended for normal daily use).
Leave 10 cm of free space around the freezer for proper ventilation of the walls.
Check that the condensation tray (automatic frost-free system) is not blocked.
If the problem persists after these checks, consult your documentation or contact an authorized VALBERG repairer.

Question 7

Why is my VALBERG UF NF 254 freezer heating up and stopping?

Accepted Answer

If your VALBERG UF NF 254 F S180C freezer is heating up and stopping, first check these points:

Set the thermostat correctly - Using the temp button on the control panel, set the temperature to -20°C for normal operation. A setting that is too high causes the appliance to work excessively.
Close the door properly - Ensure that the door is completely closed and that the seals are in good condition. If the door remains slightly open, an alarm will activate after 2 minutes, and the appliance will gradually warm up.
Do not put hot food in - Wait for food to cool to room temperature before placing it in the freezer. Hot food overloads the cooling system.
Check the ambient temperature - Your freezer operates optimally between 10°C and 43°C (depending on the climate class, visible on the technical data sheet). If the room is too cold or too hot, adjust the appliance accordingly.
Do not overload - An internal overload slows down the circulation of cold air. Avoid blocking the internal air outlets.

If the problem persists after these checks, it may be a malfunction of the compressor or thermostat that requires technical intervention.

Question 8

How to change the opening direction of the door of the VALBERG UF NF 254 F S180C freezer?

Accepted Answer

To change the opening direction of the door of your VALBERG UF NF 254 F S180C freezer, follow these precise steps:

1. Preparation

Unplug the appliance to ensure your safety.
Completely empty the freezer to facilitate door handling.

2. Removing the door

Identify the hinges usually located at the top and bottom of the current side of the door.
Using a suitable screwdriver, unscrew the hinge screws.
Gently lift the door to remove it.

3. Installing hinges on the other side

Locate the designated spots for the hinges on the opposite side of the freezer. These holes are often pre-drilled.
If no holes are present, you will need to carefully drill while respecting the dimensions of the screws.
Attach the hinges on this new side using the screws.

4. Reassembling the door

Align the door with the new hinges.
Tighten the hinges securely to ensure a good fit.
Check that the door opens and closes without resistance.

5. Final check

Plug the freezer back in.
Ensure that the door is properly sealed and that the appliance is functioning normally.

This operation allows you to adapt the door opening according to your layout needs. If you encounter difficulties, it may be helpful to seek assistance from a professional to avoid damaging the appliance.

Question 9

What is the purpose of the freezing position button on the VALBERG CF 198 E W625C freezer and how do I use it?

Accepted Answer

The freezing position button on the VALBERG CF 198 E W625C activates the Super Freezing function, designed to quickly freeze a large quantity of food while preserving its nutritional qualities. This function lowers the temperature to -30°C (or -22°F) and increases the compressor's operating speed.

How to use the Super Freezing function:

Press the Super Freezing/Lock/Unlock button (button 7 on the control panel). The Super Freezing indicator light will turn on to confirm that the mode is activated.
The temperature display will show -30°C when the compressor is running continuously.
If you need to freeze a large quantity of food, it is recommended to activate this function 5 hours in advance so that the freezer reaches the optimal temperature.

Deactivating the Super Freezing function: The function automatically stops after 24 hours of continuous compressor operation, or you can press the button again to deactivate it manually. It also stops in the event of a power failure.

Practical tip: Use the Super Freezing function only when you actually need to quickly freeze a large quantity of food. This function consumes more energy, so it is recommended not to use it continuously but to deactivate it once the food is well frozen.

Question 10

What does the error code A45 F mean on the VALBERG CF 198 E W625C refrigerator and how can it be resolved?

Accepted Answer

The error code A45 F displayed on your VALBERG CF 198 E W625C refrigerator generally indicates a problem related to the operation of the appliance, often associated with a malfunction of the cooling system or an anomaly detected by the internal sensors.

Possible meaning of code A45 F

This code may signal:

A temperature fault, for example, a temperature that is too high or a defective temperature sensor.
A problem with the automatic defrosting system, such as excessive frost buildup.
An electrical anomaly or an internal connection issue.

What to do to resolve this issue?

Check the temperature: Ensure that the temperature is set correctly, usually between 0 and 4 °C for the refrigerator section.
Check the power supply: Make sure the appliance is properly plugged in and that the outlet is functioning correctly.
Inspect the defrosting: If your model has automatic defrosting, check for excessive ice buildup that could hinder operation.
Clean the ventilation grilles: Ensure they are not blocked by dust or objects.
Restart: Unplug the appliance for a few minutes and then plug it back in to see if the code disappears.

If after these checks the error code persists, it is recommended to contact a qualified technical service for a thorough diagnosis and possible repair.

User manual VALBERG Freezer : user manuals and guides in PDF

Models VALBERG Freezer most viewed

Other categories VALBERG

Recent questions about Freezer VALBERG