Q: What does error code E1 mean on the VALBERG 14S42 D WAD929C dishwasher?

The error code E1 on your VALBERG 14S42 D WAD929C means "Extended filling time" . This indicates that the appliance is having difficulty filling with water during the wash cycle. Possible causes: The water tap is not fully open The water supply (inlet hose) is blocked or pinched The water pressure in your installation is too low An inlet water filter is clogged What to do: Start by checking that the water tap is fully open and inspect the inlet hose to ensure it is not bent, crushed, or blocked. Also, clean the inlet water filter if necessary. If the problem persists after these checks, contact a qualified technician, as the malfunction may be related to the internal hydraulic system of the appliance.

Q: How to access and use the self-cleaning program on the VALBERG 14S40 B WAD929C dishwasher?

The VALBERG 14S40 B WAD929C dishwasher indeed has a Self-Cleaning program among its 9 available programs. This program is intended for the automatic maintenance of the appliance's tub. According to the technical documentation for this model, the Self-Cleaning program is part of the standard list of cycles offered (Auto, Economic, Quick, 58 min, 90 min, Hygiene, Glass, Prewash, and Self-Cleaning). However, the PDF manual does not specify exactly which button or key to press on the control panel to specifically access this program . As a general rule, on this type of dishwasher: Programs are accessible via a rotary button or a program selector located on the front panel. You should find "Self-Cleaning" or "Auto Clean" in the list displayed when you turn the selector. Once the program is selected, press the start/on button to initiate the cycle. We recommend checking the

Q: What should I do if the VALBERG 14S42 C XAD929C dishwasher displays the salt and rinse aid symbols with dashes and refuses to restart?

This symptom indicates that the machine detects a lack of regenerating salt and rinse aid . The display of the symbols with dashes means that these two levels are too low to allow the start of a cycle. Here’s how to resolve the issue: Fill the salt compartment - located at the bottom of the machine, under the lower basket. Pour in the special dishwasher salt until it is full. Fill the rinse aid reservoir - located inside the door, usually at the bottom left. Use a dedicated rinse aid product or a combined dishwasher product. Close the covers of both compartments. Turn the machine on and start a short cycle. The machine should restart normally. If you had opened the door during a wash, know that this simply paused the cycle without damaging the appliance. Once the salt and rinse aid are replenished, the machine will resume its standard operation. Tip : After each salt refill, immediately run a short program to avoid internal corrosion, as indicated in the manual.

Q: How to start a wash cycle on the VALBERG 14S42 D WAD929C dishwasher?

To start a wash cycle on your VALBERG 14S42 D WAD929C , follow these steps: Load the bottom basket first, then the top basket Pour the detergent into the designated compartment Check that the water supply is open Press the Power button to turn the appliance on Select a program using the control buttons (ECO, Auto, Intensive, Universal, Glasses, 90 min, Quick, or Soak) - the program indicator will light up Press the Start/Pause button to begin the cycle Tip: If you want to delay the start, the Delay Start button allows you to schedule the launch up to 24 hours later. The available programs range from Soak (15 min) to the Intensive program (205 min), depending on the soiling of your dishes.

Question 1

What does error code E1 mean on the VALBERG 14S42 D WAD929C dishwasher?

Accepted Answer

The error code E1 on your VALBERG 14S42 D WAD929C means "Extended filling time". This indicates that the appliance is having difficulty filling with water during the wash cycle.

Possible causes:

The water tap is not fully open
The water supply (inlet hose) is blocked or pinched
The water pressure in your installation is too low
An inlet water filter is clogged

What to do:

Start by checking that the water tap is fully open and inspect the inlet hose to ensure it is not bent, crushed, or blocked. Also, clean the inlet water filter if necessary. If the problem persists after these checks, contact a qualified technician, as the malfunction may be related to the internal hydraulic system of the appliance.

Question 2

How to access and use the self-cleaning program on the VALBERG 14S40 B WAD929C dishwasher?

Accepted Answer

The VALBERG 14S40 B WAD929C dishwasher indeed has a Self-Cleaning program among its 9 available programs. This program is intended for the automatic maintenance of the appliance's tub.

According to the technical documentation for this model, the Self-Cleaning program is part of the standard list of cycles offered (Auto, Economic, Quick, 58 min, 90 min, Hygiene, Glass, Prewash, and Self-Cleaning). However, the PDF manual does not specify exactly which button or key to press on the control panel to specifically access this program.

As a general rule, on this type of dishwasher:

Programs are accessible via a rotary button or a program selector located on the front panel.
You should find "Self-Cleaning" or "Auto Clean" in the list displayed when you turn the selector.
Once the program is selected, press the start/on button to initiate the cycle.

We recommend checking the

Question 3

What should I do if the VALBERG 14S42 C XAD929C dishwasher displays the salt and rinse aid symbols with dashes and refuses to restart?

Accepted Answer

This symptom indicates that the machine detects a lack of regenerating salt and rinse aid. The display of the symbols with dashes means that these two levels are too low to allow the start of a cycle.

Here’s how to resolve the issue:

Fill the salt compartment - located at the bottom of the machine, under the lower basket. Pour in the special dishwasher salt until it is full.
Fill the rinse aid reservoir - located inside the door, usually at the bottom left. Use a dedicated rinse aid product or a combined dishwasher product.
Close the covers of both compartments.
Turn the machine on and start a short cycle.

The machine should restart normally. If you had opened the door during a wash, know that this simply paused the cycle without damaging the appliance. Once the salt and rinse aid are replenished, the machine will resume its standard operation.

Tip: After each salt refill, immediately run a short program to avoid internal corrosion, as indicated in the manual.

Question 4

How to start a wash cycle on the VALBERG 14S42 D WAD929C dishwasher?

Accepted Answer

To start a wash cycle on your VALBERG 14S42 D WAD929C, follow these steps:

Load the bottom basket first, then the top basket
Pour the detergent into the designated compartment
Check that the water supply is open
Press the Power button to turn the appliance on
Select a program using the control buttons (ECO, Auto, Intensive, Universal, Glasses, 90 min, Quick, or Soak) - the program indicator will light up
Press the Start/Pause button to begin the cycle

Tip: If you want to delay the start, the Delay Start button allows you to schedule the launch up to 24 hours later.

The available programs range from Soak (15 min) to the Intensive program (205 min), depending on the soiling of your dishes.

Question 5

What is water hardness and how to determine it for this dishwasher?

Accepted Answer

Water hardness measures its concentration of minerals, particularly calcium and magnesium. This information is crucial for properly setting up the softener of your VALBERG 10S44 D SAD929C dishwasher, in order to optimize the consumption of regenerating salt and the quality of washing.

Hardness levels of the VALBERG 10S44 D SAD929C

Your dishwasher offers 6 hardness levels (H1 to H6):

H1 (0-5°fH): very soft water, no regeneration required
H3 (12-17°fH): factory default level
H6 (35-55°fH): very hard water, maximum salt consumption

How to know the hardness of your water

Contact your local water service to find out the hardness of the water in your area. You can also check your local water authority's website or ask directly at your town hall. Once this information is obtained, set the corresponding softener level by accessing the setting mode (open the door, turn on the device, then press the Program button for at least 5 seconds within 60 seconds of powering on).

Salt consumption according to hardness

The harder the water, the higher the salt consumption: about 12 g per cycle for H3, up to 60 g per cycle for H6. Make sure to keep the salt compartment filled (about 1.5 kg of salt for dishwasher).

Question 6

How to adjust the door tension of the VALBERG FBI 10S44 D dishwasher?

Accepted Answer

Adjusting the door tension is not an authorized intervention for the user on the VALBERG FBI 10S44 D. The manufacturer's manual does not provide any procedure for adjusting the hinges or the closing tension by the user.

If the door has a closing issue, here’s what you can check before contacting a technician:

The door alignment - Ensure that the door closes without excessive effort and that the seal does not get stuck
The condition of the sealing gasket - Regularly clean the gasket with a damp cloth to remove food residues that may hinder closing
The hinges - Visually inspect them for signs of wear, especially if the door slightly opens by itself or slams too hard

Contact a technician: Any adjustment of the hinges or tension should be entrusted to a qualified professional. This intervention requires specialized tools and exceeds the scope of user maintenance on this model. Please contact VALBERG customer service or an authorized technician.

Question 7

How to adjust or repair the door closure of the VALBERG FBI 10S44 D dishwasher?

Accepted Answer

The manual for the VALBERG FBI 10S44 D dishwasher does not contain a procedure for adjusting the door tension. This type of adjustment is generally not a user intervention on this model.

However, if your door does not close properly, first check:

The alignment of the door - Make sure it closes without excessive resistance and that the sealing gasket (or 'seal') is not pinched. The manual recommends regularly cleaning the gaskets with a damp cloth to avoid residue buildup.
The condition of the hinges - If the door 'wobbles', partially opens by itself, or slams shut, the hinges may be worn or loose.
The Activ'door function - This model has an automatic opening at the end of the cycle for drying. Check that this function does not interfere with your manual closure.

Recommended solution: Contact VALBERG customer service (via Electro Dépôt, the distributor of the model) or a certified technician. The adjustment or replacement of closure parts (springs, hinges) should be carried out by a professional.

Question 8

Can I use the VALBERG 14S42 D WAD929C dishwasher with cold water only?

Accepted Answer

Yes, the VALBERG 14S42 D WAD929C dishwasher operates exclusively with cold water.

This appliance must be connected to a cold water supply hose only, with a filtered connection of 1.9 cm. The dishwasher does not require a connection to the hot water supply of the household.

Internal Heating Operation

The appliance has a built-in heating element that automatically heats the incoming cold water to reach the required temperature according to the selected program:

Quick Program: 45°C
Universal Program: 55°C
Intensive Program: 65°C
Eco Program: 50°C

If the heating does not work properly, the error code E3 will be displayed, indicating that the required temperature is not reached. In this case, check the heating element or contact customer service.

Question 9

What do the buttons and indicators on the control panel of the VALBERG 14S40 B WAD929C dishwasher mean?

Accepted Answer

The control panel of the VALBERG 14S40 B WAD929C, located on the door of the appliance, includes the following elements:

Program Selector

A selector allows you to choose from 9 washing programs:

Auto: adaptive program
Economical: reduces water and energy consumption
Quick: short cycle
58 min and 90 min: fixed duration cycles
Hygiene: intensive washing at high temperature
Glass: delicate program
Pre-wash: initial rinsing
Self-cleaning: cleaning of the tub

Buttons and Indicators

Start Button: starts the selected cycle
Delayed Start: schedules a delay of 1 to 24 hours before starting
Half Load: reduces consumption for a lightly loaded dishwasher
Salt Indicator: lights up when the regenerating salt tank is empty
Activ'Door Function: the door automatically opens at the end of the cycle to facilitate drying

The online manual does not contain a detailed annotated diagram of all the symbols on the panel. The information above covers the main elements and their functions. For specific symbols of each indicator light, refer to the paper manual provided with the appliance or the labels attached inside the door.

Question 10

What is the weight of the VALBERG 14S42 C XAD929C dishwasher?

Accepted Answer

The weight of your VALBERG 14S42 C XAD929C dishwasher is approximately 45 kg.

This information is useful if you need to arrange its transport, installation, or check the capacity of your countertop. The dishwasher has the following dimensions:

Width: 600 mm
Depth: 600 mm
Height without countertop: 815 mm
Height with countertop: 845 mm

User manual VALBERG Dishwasher : user manuals and guides in PDF

Models VALBERG Dishwasher most viewed

Other categories VALBERG

Recent questions about Dishwasher VALBERG